MANUAL ENGLISH Single WDP-1 V1 Ordercode: 50756 Highlite International B.V.
Single WDP-1 Table of contents Warning ...............................................................................................................................................................................2 Safety Instructions .........................................................................................................................................................2 Operating Determinations ................................................................................................
Single WDP-1 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
Single WDP-1 IMPORTANT! The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device. • • • • • • • • • • • • • • • • • • • • • • Never let the power cord come into contact with other cables! Handle the power cord and all connections with the mains with particular caution! Never remove warning or informative labels from the unit. Never leave any cables lying around. Do not insert objects into air vents.
Single WDP-1 Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued. Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility. Call Highlite 0031-455667723 or mail aftersales@highlite.nl and request an RMA prior to shipping the fixture.
Single WDP-1 Description of the device Features The Showtec Single WDP-1 is a 1-channel DMX dimmer/switch with a built-in wireless DMX receiver. It is possible to mount the Single WDP-1 to any wall, truss or a fixture which makes it suitable for any location.
Single WDP-1 HTP (Highest Takes Precedence) If the DMX input value is higher than the fader (03/10) value, then the DMX input will take precedence over the fader input. Similarly, if the fader (03/10) value is higher than the DMX input value, then the fader input will take precedence over the DMX input. Installation Remove all packing materials from the Single WDP-1. Check if all foam and plastic padding is removed. Connect all cables.
Single WDP-1 Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode. Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa. Connect the device to the main power supply. The Single WDP-1 is equipped with the power failure memory.
Single WDP-1 Control Panel A) B) C) D) E) F) LED display DMX LED indicator MENU button UP button DOWN button Wireless DMX LED indicator Fig. 04 Control Mode The Single WDP-1 is individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address, next time.
Single WDP-1 Main Menu Options 1. Remote control/Manual control 2. DMX Addressing (Fun1) 3. Dimmer/Switch (Fun1) 4. Dimmer Limit (Fun1) 5. WDP Control (Fun1) 6. Dimmer Preset (Fun2) 7. Full On (Fun2) 1. Remote Control/Manual Control 01) Press the MENU button until the display shows or 02) Press the UP/DOWN buttons to choose between . (DMX/wireless DMX receiver enabled) and (manual mode). Note: If you have chosen , please read sections 2-5. If you have chosen , please read sections 6-7. 2.
Single WDP-1 7. Full On (Fun2) 01) Once you have set the device to (see section 1), press the MENU button until the display shows . 02) The dimmer is now set to its maximum value (full on). It is not possible to adjust any settings. DMX Channels 1 channel Channel 1 – Dimmer intensity 0-255 From dark to brightest Maintenance The operator has to make sure that safety-related and machine-technical installations are to be inspected by an expert after every year in the course of an acceptance test.
Single WDP-1 Product Specification Model: Input voltage: Fuse: Dimensions: Weight: Showtec Single WDP-1 230V AC, 50Hz F10L/250V 100 x 95 x 273 mm (LxWxH) 1,4 kg Operation Signal input: Signal output: Output: 3-pin DMX IN 3-pin DMX OUT 10A Schuko Electro-mechanical effects Housing: Color: Control: Voltage and amperage indication: Metal & flame retardant plastic Grey 50 mm dimming fader LED display Max. ambient temperature t a : Max.
Single WDP-1 Notes Ordercode: 50756 12
Single WDP-1 Ordercode: 50756 13
Single WDP-1 Ordercode: 50756 14
©2016 Showtec
