Instructions / Assembly
5-1. If you need to use voice control, please ensure that:
Voice converter is connected to the network.
Your Google assistant or Amazon alexa is connected to the network.
The USB power cable is connected as shown below
1
Specif ication
Package contents and specification Installation notes
INSTRUCTION MANUAL
VOICE COMMAND CONVERTER
1004325284
INPUT: 100-240V ~ 50/60Hz, 0.3A
OUTPU T: 5V 1000mA
OPER ATION: Indoor
OPER ATING TEMPER ATURE: -15° F TO 90° F (-26° C TO 32° C)
WARRANT Y: One Year Limited
www.ishowtree.com
Scan & See Me!
Installation notes
Instructions for use
Connect the power adapter to the power supply
2
3
1
3
1 2
3
7
6
10 118 9
2
Plug in USB to adapter
Plug in the other end(Micro USB)into the converter
You can fix the product on the wall as follows:
e. Fasten the top cover of the base and place the voice converter
on the base.As shown in Figure 3-e
Put into the hole
۲ރЯԤுԬӲYO`K 33
封面
封底
Installation notes
4
A
D
G
F
E
B
C
Voice command converter
Converter base
Set screws plastic parts
USB power cable
Adapter
Audio line
Audio splitter connector
Punch mark paper
A
B
C
D
E
F
G
H
1
1
3
1
1
1
1
1
PART DESCRIPTION QUANTITY
a. Insert a tool to remove the top cover of the base.
As shown in Figure 3-a
c.Fix the punch mark paper and use a drill or other tool to punch holes
in the corresponding three holes (please be safe, be careful not to hurt
your fingers).As shown in Figure 3-c
b.Place the punch mark paper on the wall you want to fix.
As shown in Figure 3-b
(Figure 3-a)
Audio
1.Put the audio input port into AUX as below shown
2.Connect the audio line between the audio
input interface and your phone(or other music player),
then the lights will flash follow the music beat.
Audio interface
Audio input: support connecting
earphones and other audio play device
AUX
Input
Input
AUX
Installation notes
5
Instructions for use
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide r
easonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipmen
t does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the i
nterference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Punch mark paper
Screw holes
Electrodrill
Note:The diameter of the hole is about
5mm, and the depth of the hole is about
35mm
Tighten
with a tool
(Figure 3-b)
(Figure 3-c)
d. Use a tool to insert the plastic expansion plug into the hole, then
place the base alignment hole on the wall, and finally lock the
thread into the hole.As shown in Figure 3-d
(Figure 3-d)
(Figure 3-e)
Lights
Button
Rainbow color rotation The device is in the state to be configured.
You can use the APP to configure it.
The blue light slowly dims after it lights up The device has
successfully connected to the network, and you can use it normally.
Red light rotation Disconnected from the network, please
confirm the network or press and hold the bottom RESET
button for 5 seconds to reset to the initial state.
The green light slowly dims after it lights up Prompt voice
command has been triggered.
Press the button at the bottom of the device and hold for more
than 5 seconds, you can reset the Wi-Fi.
The product can be connected to an external audio source. At this time,
the related Bluetooth products will follow the music, as follows:
1
3
2
The main state indicated by the lights as below:
Instructions for use Instructions for use
APP
a. Download the “Holiday Showhome” App from App Store(IOS) or Google Play(Android)
b. Open the “Holiday Showhome” App and sign in.
c. Click the Add Device button and select the Wi-Fi
d. Click the Quickly add button after the scan is complete
Notes:You can also click the Skip button to skip the login screen and use
the visitor mode, but you will not be able to use voice control at this time.
e. Return to the home interface and click on the device to enter the operation interface.
Voice
5-2. Voice control example for Google assistant:
Instructions for use Instructions for use
4
5
Bluetooth products
6
Or you can directly scan the QR code below to download:
User : Ok,google,ask Show Home (This is the brand name).
Google : You have voice converter and show tree and ultimate string,
which device do you wat to contorl ?
Google : Ok,voice converter is ready,which function you want to try ?
Google : Ok,the color has changed to red.
Google : Ok,the mode has changed to steady.
User : Voice converter ( This is the product name ).
User : Red ( Color name.Other colors and themes are shown as below ).
User : Steady (Mode name.Other modes are shown as below).
Mode :
Turn on, Turn off, Steady, Sparkle, Blink, Fade, Waves, Rolling,
Instead, Fireworks, Rainbow, Color Band, Show mode
Red, Green, Blue, White, Orange, Pink, Yellow, Gold, Cyan,
Magenta, Purple, Christmas Day, Valentines’ Day, Independence
Day, Halloween, ST Patrick’s Day, Thanksgiving, Multi-Color,
This device is used to control other Bluetooth products. The specific list is as follows:
Colors and themes :
Holiday Showhome C9 Lights(24L)
Holiday Showhome C9 Lights(48L)
Holiday Showhome Icicles(24L)
Holiday Showhome Icicles(48L)
Holiday Showhome Candy Canes
Holiday Showhome LED Light Strip(10ft)
Holiday Showhome LED Light Strip(20ft)
Holiday Showhome LED Spotlights
Holiday Showhome RGB Show Tree
(Android) (IOS)