Specifications

73
1-800-543-7586
Cut your sanding time in half and
achieve smoother surfaces with
these versatile Hand Scrapers
Hand Scrapers will remove materials much
faster than sandpaper and, at the same time,
eliminate uneven spots that abrasive materials
will only tend to magnify. In addition to their
superior smoothing qualities, they will also
prove most useful in removing old finishes and
glue with incredible ease and precision.
This complete set includes a rectangular
scraper, a concave/convex scraper, and a
“goose-neck” scraper for moldings and shaped
edges of all types.
518666
Set of 3 Hand Scrapers
$14.39
Inflatable Sander uses your MARK V
Lathe to shape or smooth contours
and profiles
Just mount this 2
1
/
4
˝
diameter x 8
˝˝
long sander
between the centers of your MARK V’s Lathe
(Tailstock Live Center, 505602 required for use,
see Page 78
and inflate it to the pressure you
want (up to 15# psi) with a bicycle pump. Sands
flat surfaces (at max inflation) or contoured
shapes (at low pressure) with equal ease.
High-quality construction with metal ends and
canvas-over-rubber drum. Includes one 100-
grit/medium aluminum oxide sleeve.
754200
Contour Sanding Drum
$75.17
Aluminum Oxide Replacement Sanding
Sleeves
(5 sleeves per pack)
754201
Coarse – 80-grit
754202
Medium – 100-grit
521760 Fine – 120-grit
754203
Ultra-Fine – 150-grit
$22.34 Each
Astonishing results on
surfaces up to 4˝ wide
• Joint highly figured woods without
tearing or chipping
• Produce glue-quality edges on
sheet goods
• Shave end grains to length with
glass-smooth results
• Achieve precision-ground surfaces
on edged tools
A few years back during an annual inventory, a
Shopsmith engineer pulled a box out of a dark,
neglected corner of the warehouse ... opened it,
and discovered a Conical Sanding Disc made by
Magna Engineering (the original manufacturer of
Shopsmith equipment).
Lucky for all of us, he had used a Disc just
like this at a woodworking company where he
had been employed several years earlier, recalled
its incredible capabilities and set out on a
“mission” to bring this extremely versatile
product back to the market.
Since then, we’ve sold thousands of these
amazing Discs and all who use them continue
to sing their praises.
How does it work?
The heavy steel Disc is made with a precise,
4° tapered, cone-like shape. When using it, the
MARK V’s Table is tilted to that same 4° angle
and a Rip Fence or Miter Gauge used as a guide
to keep the stock moving in a straight line.
As the stock is moved past the Disc, a narrow
band (less than 1/4˝ wide) is created where the
full workpiece edge (up to 4˝ tall) is in contact
with the abrasives.
Within this band, all of the abrasive materi-
als and the workpiece edge move parallel with
one another and in opposing directions. This
is straight-line abrasion in its purest sense. No
wonder there are no swirl marks. It’s magic!
Puts a glass-smooth, glue quality
finish on even the most difficult edges
No edge is too uneven or tough. Unlike your
Jointer, the Conical Disc will shave the edges
of highly figured birdseye or BURL woods with-
out tearing or chipping. Where materials such
as plywoods, particleboard, MDF and plastic
laminate-covered composites will eat up Jointer
knives, they’re no problem for the Conical Disc.
Remove up to 1/8˝ in a single pass!
A 1/8˝ pass across the edge of composites
and highly figured woods is almost certain
to produce undesirable results. NOT with the
Conical Sanding Disc. Grab a 2˝ x 2˝ piece of
figured wood or composite, make your set-up
for a 1/8˝ pass according to your Disc Manual,
follow all operational and safety instructions and
shove it through. WOW!
555477
Conical Disc Sanding
$69.39
Pkg. (Includes Disc and Assorted Disc Pack)
YOU SAVE $7.59
555435
Conical Sanding
$58.09
Disc (only)
Conical Sandpaper Discs
Pressure-sensitive aluminum
oxide Discs. Three per
package. Assorted Pack
includes one each 50, 80
and 150-grit Discs.
555430
50-Grit
555431
80-Grit
555433
150-Grit
555434
Assorted (One Ea. – 50, 80 & 150-Grit A/O Discs)
$18.89 Each
High-tech design, high-quality results
The infeed side of the Disc – NOT THE OUTFEED
SIDE – contacts the workpiece’s surface at a
90° angle, parallel to the grain.
The 4° taper begins 1
1
/
4
˝ from the center of the
disc and continues to its outside edge. This taper
gives the disc its cone-like shape.
TOP VIEWFRONT VIEW
4°
Conical Sanding
Achieve super-smooth, swirl-free sanding results on even
the most troublesome workpiece edges and surfaces with
the remarkable Shopsmith Conical Sanding Disc