Specifications

70
www.shopsmith.com
All Shopsmith Shaper Cutters may be used on any
shaper that accepts 1/2˝ bored Cutters. For safety
reasons, we recommend that these cutters always
be used with a Shaper Fence
See Page 69 when
straight-line shaping.
All Shaper Cutters are $18.95,
unless otherwise specified.
3/16˝ Cove & Bead
555009
(Mirror image of
505618)
Bead & Bevel
505613
1/4˝ & 1/2˝
Combination
Quarter Round
505608
Crown
505606
2.
Bead
505605
1.
Bead & Quarter
Round
505607
3. 4. 5.
Flute & Quarter
Round
505934
6.
Glue Joint
555095
9.
1˝ Jointer
505611
7.
Quarter Round
& Cove
505614
10.
Cabinet Door
Lip
555589
8.
Drop-Leaf Cove
515326
(Mirror image of
515327)
21.
Drop Leaf Bead
515327
(Mirror image of
515326)
22.
3/16˝ Bead & Cove
505618
(Mirror image of 555009)
23. 24.
Cloverleaf
505616
12.
Groove
505609
(Mirror image of
505610)
14.
Tongue
505610
(Mirror image of
505609)
13.
3-Bead Edge
555011
(For use on 3/4
˝
stock)
11.
1/4˝ Groove
505612
15.
Ogee
505932
16.
Vee Groove
505935
19.
3/4˝ Flute
555048 (Mirror
image of 555049)
17.
3/4˝ Nosing
555049 (Mirror
image of 555048)
18.
1/2˝ Radius
555010
20.
1/2˝ Groove
505938
25.
3-Bead
505933 (Mirror
image of 555012)
27.
3-Flute
555012 (Mirror
image of 505933)
26.
Complete Cabinet Set
505937 Performs comparably
to the Sash and Door Cutter Kit
(6 cutters total).
$104.15
28.
Make beautiful cabinet doors with the
Door Panel Cutter and Door-Rail Coper
with your shaper
Use the Door Panel Cutter to cut the panel grooves
in the edge of the rails and stiles. Cut the ends of
the rails with the matching Door-Rail Coper Knife.
555078 Door Panel Shaper Cutter (Mirror image of 555079) $18.95
555079 Door-Rail Coper Shaper Cutter (Mirror image of 555078) $18.95
Oscillating Drum Sander extends Drum
Sleeve life, produces smoother results
and eliminates workpiece burning
This work-saving accessory attaches to your
MARK V (in Drill Press mode) and is powered
solely by its Auxiliary Spindle. Once installed, it
will provide an unassisted, continuous up-down
oscillating action that’s always exposing fresh
abrasives to the wood and cleaning the Sleeve
while you work.
As a result, you’ll spend a lot less time
sanding and produce much smoother results
without having to worry about unsightly abrasive
marking or burning the edges of your stock.
It’s easy ...
Just set your MARK V up for Drill Press opera-
tion as you normally would for Drum Sanding.
Clamp the Gearbox Mount around your MARK
V’s Way Tubes, install the Power Coupler,
replace the Quill Handle with the Sander Lever
Arm and attach the Cable.
In less than five minutes, you’ll be ready
to start sanding faster, smoother and more
economically than ever before.
Works with any Shopsmith Drum Sander from
our smallest 1/2˝ by 2˝ Drum to our all-new
2
1
/4˝by 6˝ Drum.
555754 Oscillating Drum $148.58
Sander
Enjoy added sanding control with our
Drum Sander/Shaper Fence Kits.
See Page 72 for more information
Shaper Cutters
A full complement of premium Shopsmith Shaper
Cutters for decorative edging, joinery and more