Specifications
61
1-800-543-7586
Parts Price List
BELT SANDER
Ref. Price
No. Part No. Description Qty. Each
11 503024 Tinnerman Clip 4 $0.80
12 5030049 Shaft Cap 1 4.34
— 513061 Table Tilt Assembly (incl. 13-15) 16.25
13 † Table Tilt Lock 1
14 † Retaining Ring 1
15 † Locknut 1
16 502999 Indicator 1 5.82
17 502998 Indicator Washer 1 3.43
18 448309 Self-Tapping Screw, #8-32 x 1/4˝ 1 0.80
19 51485402 Dust Chute 1 8.87
19A 514521 Elbow, 2-1/2˝ Diameter 1 7.39
19B 124818 Hex Jam Nut, 1/4˝-20 2 0.80
20 502698 Trunnion Nut, 3/8˝-24 1 0.80
21 502988 Cup 1 1.96
22 120388 Flat Washer, 3/8˝ 1 0.80
— 503402 Base Assembly (incl. 23-25) 51.78
23 † Base Casting 1
24 † Drive Stud 2
25 † Trunnion Guide 1
— 515565 Inner Frame Assembly (incl. 26-28) 73.51
26 † Rollpin, 1/4˝ x 5/8˝ 2
27 † Trunnion 1
28 † Right Frame Side 1
30 5029639 Backup Plate 1 28.27
31 514050 Slotted Flathead Screw 6 0.80
32 51553801 Left Outer Frame 1 53.38
33 445446 Tinnerman Clip 6 1.46
34 502985 Trunnion Washer 1 0.88
35 502974 Trunnion Stud 1 11.57
36 502989 Trunnion Lock 1 14.57
IDLER DRUM
— 502934 Idler Drum Assembly (incl. 37-47) 105.69
37 513732 Split Pin, 3/16˝ x 7/8˝ 1 0.80
38 502945 Guide Bushing 2 7.14
39 † Tension Cam 2
40 † Bearing 2
41 † Idler Drum 1
42 † Spring Plug 2
43 504553 Washer, 5/8˝ 2 0.93
43A 515619 Curved Washer 1 1.95
44 502937 Thrust Washer 2 0.80
45 † Idler Shaft 1
46 † Torsion Spring 1
47 † Rollpin 1
TENSION KNOB
— 502874 Tension Knob Assembly (incl. 48-54) 15.62
48 † Retaining Ring 1
49 † Lock Washer 1
50 † Latch Spring 1
51 † Tension Knob 1
52 † Drive Screw 1
53 † Washer, 1/8˝ 1
54 † Knob Latch 1
55 501027 Retaining Ring 1 0.80
56 502923 Medallion 1 0.80
DRIVE DRUM
— 502789 Drive Drum Assembly (incl. 57-62) 107.01
57 † Ball Bearing 2
58 † Bushing 2
59 † Drive Drum 1
60 † Rollpin 1
61 † Drive Shaft 1
Ref. Price
No. Part No. Description Qty. Each
62 † Drive Sleeve 1
63 502961 Finger Washer 2 $1.52
64 513191 Socket Head Cap Screw, 1/4˝-20 x 1˝ 2 0.80
TABLE
— 503406 Table Assembly (incl. 65-71) 158.65
65 † Rollpin, 1/4˝ x 7/8˝ 2
66 120388 Flat Washer, 3/8˝ 1 0.80
67 518307 Table Lock Bolt 1 2.82
67A 502318 Special Washer 1 2.98
68 † Table 1
69 502992 Support Spacer 1 7.28
70 † Tilt Slide 2
71 † Drive Stud 2
— 503407 Support Assembly (incl. 72, 73) 49.84
72 † Mounting Rod 2
73 † Table Support 1
MISCELLANEOUS
74 5137779 Eccentric Mounting Tube 2 17.72
75 115321 Setscrew, 5/16˝-18 x 5/16˝ 2 0.80
76 120377 Hex Nut, 3/8˝-16 1 0.80
77 120394 Washer, 3/8˝ 2 0.80
78 122181 Hex Head Cap Screw, 3/8˝-16 x 2˝ 1 0.80
79 5035769 Drive Hub 1 2.58
80 222458 Setscrew 1 0.80
— 51368601 Allen Wrench, 5/32˝ 1 1.74
† Not available as a service part.
Tips & Techniques
• For the safety and well-being of the built-in motor,
it is always preferable to have the MARK V
connected to an independent line without an
extension cord. If it is necessary in your situation
to use an extension cord, it must be of heavy
enough gauge cord to provide the proper current.
For extension cords up to 20 feet, use no less
than a 14-gauge, three-conductor cord. For
20-100 feet, use no less than a 10-gauge,
three-conductor extension cord.
• Please remember that the cord and plug should be
replaced immediately if they become damaged.
No matter how long you’ve owned your MARK V,
it needs a little tender care after every 10 hours of
operation. This will guarantee trouble-free wood-
working year after year:
• Run your MARK V up to high speed, turn off and
unplug it. Remove the screws holding the belt
cover and slide it away from the headstock. Also,
remove the nameplate with a screwdriver (this
plate can’t be removed on 1953 and 1954
models – drop the motor instead).
• Clean the sawdust out of the headstock with an air
compressor, vacuum cleaner or tire pump. Check
the belts for wear, then lubricate the motor shaft
and sheave with two drops of 3-in-1 oil.