Specifications

37
1-800-543-7586
Auxiliary Table matches Cross-Cut Table height on
opposite side of Blade
Features a Miter Bar on the bottom that
locks into the Work Table slot on the
opposite side of the Blade when the
Cross-Cut Table is in use. Its purpose is
to match the height and thickness of the
Cross-Cut Table to keep scrap material
from falling into the Blade and causing
a dangerous kick-back. Works with all
MARK V Models.
555526 Auxiliary Cross-Cut Table $47.21
Non-Slip Strip keeps your stock from moving
as you use your Cross-Cut Table
1
1
/2˝
x 30
˝
adhesive-backed Strip
attaches to your Sliding Table’s Fence to
prevent workpiece creeping. Also works
with your Miter Gauge or any Miter
Gauge Extension Fence.
516913 Non-Slip Strip $6.46
This ingenious Sliding Table acts like a “sled” to support long or cumber-
some workpieces and help you guide them safely and precisely through
otherwise difficult crosscuts. Need to cut an inch or so off the end of an
8-foot 2
˝
x 12
˝
. No problem.
Its durable, laminated surface is a full 15
3
/4˝
x 31
3
/4˝
for plenty of
support. The Aluminum Fence adjusts quickly for 90°, 45°, 36°, 30°
and 22
1
/2
° angle cuts for making four, five, six or eight-sided projects.
Order it with your choice of MARK V Miter Bar ... or with none, for
mounting on competitive saws.
555502 Cross-Cut Sliding Table $107.30
(For Model 500 MARK V)
555535 Cross-Cut Sliding Table $107.30
(For Models 505, 510 & 520 MARK Vs)
516524 Cross-Cut Sliding Table $95.75
(No Miter Bar – Use with other brand saws)
Sawing
Shopsmith’s Support Table helps you handle long or wide boards
alone – even serves double duty as a Roller Stand!
Attaches to the infeed or outfeed end of
any model MARK V worktable in seconds.
The other end is supported by a leg that
telescopes to match the worktable height,
then locks at the twist of a knob. The
table then tilts in unison with your MARK
V’s worktable. A 14˝ wide roller top (also
included) converts the adjustable leg for
use as a Roller Stand, if desired.
The generous 24˝w x 32˝d x 1˝ thick
tabletop is covered with a low friction,
easy-to-clean laminate. Two built-in relief
slots in its surface allow your Miter
Gauge Bar to pass the worktable’s edge.
Extension Table Brackets let you use your
MARK V’s Floating Extension Tables as
Infeed/Outfeed Tables
These Brackets let you use
the Floating Extension Tables
that came with your MARK V
Model 510 or 520 as infeed/
outfeed supports when work-
ing with long or wide stock.
The System works with one of your MARK V’s 2
˝
Connector Tubes plus a special 18
˝
long Tube (with this kit)
to create a 30
˝
deep by up to 18
˝
wide surface, supported
on the opposite end by your Telescoping Legs.
Putting everything together takes less than 5 minutes
and gives you all the workpiece support and convenience
you could ask for. The Brackets will work either with a
Model 510 or 520 MARK V’* and feature a unique raising
and lowering system that lets you micro-adjust the heights
of the Floating Extension Table(s) for safe, smooth operation
using two Height Adjustment Setscrews.
The complete kit includes one 18
˝
Connector Tube, two aluminum Bracket
castings, and all necessary hardware for
assembly and operation.
555997 Extension Table Brackets $73.49
* These Brackets will also work with Model 505 MARK V’s, but require that you
purchase Floating Extension Tables (514446) and Connector Tubes (514439)
separately.
See Page 30
Accessories for handling long or wide boards more safely
Perfect for ripping long boards or large
panels, drilling, shaping, disc sanding or
performing almost any operation on difficult-
to-handle stock. Can also be used with
Model 505, 510 and 520 Floating Extension
Tables. Includes Roller Top, hardware and
instructions.
555306 Support Table $199.21
(Model 500)
555307 Support Table $199.21
(Models 505 & 510)
555784 Support Table $199.21
(Model 520/Pro Fence)
521651 Support
Table
$42.08
Conversion Kit
(Required if Support Table was
purchased prior to Model 520 upgrade)
Check It Out!
The Shopsmith Support Table
is now a Roller Stand, too!
Conversion Kit available for older
support tables – the perfect
companion when working with
long or wide workpieces.
See Page 30 for more information
Enjoy the cutoff convenience an accuracy of a radial arm saw
with Shopsmith’s Cross-Cut Sliding Table System