Specifications

31
1-800-543-7586
Practically nothing will affect the eventual quality of your woodworking projects more than the accuracy of your measurements and set-
ups. If you fail to “measure twice/cut once,” all bets are off ... and if the tools you’re using to make your cuts are out of whack, your
results will probably be likewise. The devices presented on this page will help you achieve the quality results you want.
Set-up or tune-up your tools and
operations with precision, using
this Dial Gauge
This Gauge will help you align your MARK V’s
Work Table, Rip Fence or Miter Gauge pre-sets
for precise cuts, time-after-time.
Align your Miter Gauge to an exact 45° or
90° setting. Achieve the smoothest edges and
surfaces by match-setting your Jointer Knives.
Micro-adjust the offset of Shaper and Router
Table Fences. Set the depth-of-cut for saw
blades, dado blades, router bits and more with
amazing accuracy. Measure the depths of holes
or dadoes ... the list goes on.
You get a large 2
1
/4˝ diameter Dial Indicator,
graduated in 1/1000 (.001˝) with a full 1˝ range;
a set of 22 interchangeable Indicator Points for
tackling the toughest measuring jobs; a special
Mounting Block with adjustable Bracket; a 5˝
long Miter Bar and easy-to-follow illustrated
instructions for use.
555884
Dial Set-Up Gauge
$69.99
Set your Saw’s depth-of-cut in an
instant with this Gauge
Just set the Gauge on your work table, move
your blade into position with a tooth touching
the appropriate step on the Gauge ... and lock
the blade into position.
Gauge provides 16 steps from 1/8˝ to 2˝ in
1/8˝ increments. Also works for setting Router
Bit depths and rip cut widths on Table Saws
and Bandsaws.
739990
Aluminum Step Gauge
$8.39
Get the right speed
setting for every
operation with this
handy Speed Chart
Matches rpm’s with MARK V
Speed Dial settings and
provides ideal speed for doz-
ens of operations.
791500
MARK V Speed Chart
$4.55
Measuring or transfer odd angles
with the Mite-R-Gauge Protractor/
Bevel
The measuring and setting of precise angles is
extremely important in woodworking. Triangles
are ideal for most applications, but they will not
do for many “odd” angles.
The Mite-R-Gauge Protractor/Bevel features
long legs with direct-reading protractor scales
that make easy work of this otherwise difficult
job and allows you to measure and read the
angle in a single step ... within 1/2 degree.
Once the angle is set, a quick twist of the
knob locks the gauge in position for transferring
to your table saw or other machine.
730342
Mite-R-Gauge
$21.99
Protractor/Bevel
Set Miter Gauge Angles with 1/2°
accuracy using this Precision
Protractor
This 21st century Marking Protractor has micro-
fine guide holes at every 45°, 30° 22.5°, 5°, 1°
and 0.5° interval to plot any angle with ease and
absolute accuracy. A metal T-Bar and see-through
crosshairs provide exact alignment against the
edge of your workpiece. Remove the T-Bar to work
on flat surfaces. Contains four angle scales: 0°
left to 180° right, 180° left to 0° right, 0° top to
90° left and right, and 90° top to 0° left and right
suits every need. It’s easy on the eyes, incredibly
accurate, and just plain fun to use!
522172 6˝ Incra Precision
$31.39
Marking Protractor
(Calibrated to 1/2° & 1/32 ˝)
Special Gauge helps you verify
accurate router bit depths
Set-Up & Alignment
Tool Set-Up & Alignment Aids
The quality of your results cannot exceed the accuracy of your set-ups
A dado or groove that’s too deep can jeopardize
the strength and ruin the appearance of a joint.
This handy gauge eliminates these problems by
providing accurate settings in an instant.
Just rest the gauge’s feet on your router’s
base or your router table insert and move the
appropriate notch over the tip of your bit to make
your setting. Graduated in 1/16˝ increments
from 1/8˝ to 1˝. Can also be used to set saw
blade depths up to 1˝.
521939
Router Bit Depth Gauge
$8.39