EGNR V2 USER GUIDE VERSION 1.0 Shoof Technologies Inc.
TABLE OF CONTENTS 1. Introduction ................................................................................................................. 3 2. Antenna connections ................................................................................................... 4 3. Power Connection ........................................................................................................ 6 4. Labeling ..........................................................................................
1. INTRODUCTION The EGNR V2 an FCC part 15.247compliant device that enables communication to the Shoof Technologies data network. The EGNR module communicates using the 2.4GHz ISM band. Figure 1 – EGNR module Shoof Technologies Inc.
2. ANTENNA CONNECTIONS EGNR V2 has two antenna connections: 1. 2. Main antenna – MMCX connector Diversity Antenna – MMCX connector Main Antenna Diversity Antenna Figure 2 – Antenna connector positions Shoof Technologies Inc.
Port Connector Type Antenna type Maximum gain Main Antenna MMCX Omni 4dBi Diversity antenna MMCX Patch 8dBi Table 1 - External Antennas Shoof Technologies Inc.
3. POWER CONNECTION Power connection can be applied to the EGNR V2 via the USB connector. Standard USB wiring and voltage apply. Power port is identified in following figure: Power connector X800 (USB) Figure 3 - power connector VOLTAGE LIMITATION: Function Maximum Supply voltage @ USB 5.2V Typ (Recommended) 5V Shoof Technologies Inc. Proprietary and Confidential © 2019 Minimum 4.
4. LABELING Below is an example of the FCC ID label that can be found in the location indicated in Figure 5. FCC ID: 2AR28-EGN22 IC: 24759-EGN22 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
5. MODULE SPECIFICATION i. ii. iii. iv. Physical specification Parameter Value Size (mm) 84x66x19 Weight (g) 39 Electrical Specification Parameter Value Operating Frequencies 2.4GHz Max output power +20dBm Voltage Supply 5V Notes 2.4GHz Environmental Specification Parameter Value Storage Temp -40 – +125°C Operating Temp -40 – +85°C External antenna maximum gain Frequency Maximum gain Type 2.4GHz 4dBi Omni 2.4GHz 8dBi Patch Shoof Technologies Inc.
6. FCC AND INDUSTRY CANADA GOVERNMENT GUIDELINES FCC ID: 2AR28-EGN22 IC: 24759-EGN22 Modifications (15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Part 15 Certification Notice (15.19(a)(3)) and RSS-GEN This device complies with Part 15 of the FCC Rules and ISED license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. L’antenne de cet émetteur ne doit pas se trouver à proximité de ou fonctionner en association avec une autre antenne ou un autre émetteur. L′appareil doit être installé de telle sorte que les gens ne viendront pas au sein de 20 cm (8 in.) de l′antenne.
L’extrait suivant provient du Cahier des charges sur les normes radioélectriques (CNR); exigences générales et information relatives à la certification des appareils radio, section 3.2.1, et décrit les exigences en matière d’étiquetage pour un dispositif hôte intégrant un module radio. Le dispositif hôte doit être correctement étiqueté afin d’identifier les modules qu’il comprend.
7. REGULATORY APPROVALS Japanese Type Approval EGNR V2 complies with the Japanese radio law and is certified according to ARIB STD-T108. When the product is placed on the Japanese market, it must carry the Specified Radio Equipment marking as shown below: If the certification label cannot be recognized from outside (e.g. installation in a host) appropriate information must be referenced in the user manual.
