M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5669K 16x16 HDMI MATRIX ROUTING SWITCHER 16x16 HDMI Matrix Routing Switcher w/ Full EDID Management/Learning 4k2k Capable HDMI Matrix Routing Switcher Series Thank you for purchasing the SB-5669K16x16 HDMI Matrix Routing Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 16x16 HDMI Matrix Routing Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: FEATURES ....................................................................... 2 SPECIFICATIONS ............................................................ 3 FRONT PANEL ...
FEATURES FEATURES • • • • • • • • • • • • • • Enables switching of 16x HDMI digital source devices to 16x HDMI devices. HDMI digital video w/ embedded audio, DVI format, 4K2K/60Hz-HDCP V2.2 and HDCP V1.3. Seven (7) function button control and worldwide (7) EDID modes for HDTV 4K2K resolutions. Link speeds of up to 10.2 Gbps (link clock rate of 340Mb Hz), support HDMI 1.4a 3D formats.
SPECIFICATIONS SPECIFICATIONS • • • • • • • • • • • • • • • • • • • Type of HDMI Switcher: 16x HDMI inputs to 16x HDMI outputs matrix switcher HDMI Support: HD 1080p-@60Hz, 4K2K, H36-bit deep color, 3D (1.4a) formats HDCP Support: 4K2K/60Hz-HDCP V2.2 and HDCP V1.3 Video Bandwidth: Double Data Rates:340 MHz, total 10.2 Gbps bandwidth Digital Video Support: Full HD resolution : 480i / 480p / 720p / 1080i / 1080p / 4K2K Digital Audio Support: • Multi Audio Formats 5.1 / 7.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving power. The switcher will remember the last setting during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input source 1 to 16 LED illuminate white to indicate a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR assign the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show ”0” to indicate none of the destinations are assigned a video source. Option 2 - Press ALL followed by Source 1 thru 16. The display will show the source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - MEMORY The system can save up to 16 sets of switching routes, which are stored in local memory using Source keys 1 thru 16 or Destination buttons 1 thru 16 as the memory location. - Configure desired matrices . - Press MEMORY button. - Press 1 thru 16 on either Source or Destination row. - Press ENTER to ready memory location. - Or press MEMORY again to cancel operation. Operation completes. Note: Operation will abort if no keys are dressed within 5 seconds. 13.
BACK PANEL BACK PANEL 1. DC POWER INLET: The switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. Power supply 100V~240VAC, 50/60Hz. Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power Input: 100-240VAC, 50-60Hz 1.2A 2. IR EXTENDER CONTROL: Support one of IR Extender Extend distance maximum 300m / ~1000 ft.
REMOTE CONTROL Before making any connections to the switcher, observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : POWER ON : 32CD A15E POWER OFF : 32CD A25D ALL : 32CD B04F OFF : 32CD B14E LOCK : 32CD B54A EDID : 32CD B748 RECALL : 32CD B24D ENTER : 32CD B34C MEMORY : 32CD B44B CUSTOM CODE : 32CD HOW TO GIVE IR COMMANDS: PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 32CD 01FE DESTINATION #2 : 32CD 11EF DESTINATION #3 : 32CD 12ED DESTINATION #4 : 32CD 13EC DESTINATION #5 : 32CD 14EB DESTINATION #6 : 32CD 15EA
EDID FUNCTION EDID FUNCTION SETUP EDID Setup ENTER EDID How to enter and exit EXIT 1. ENTER : After the switcher is turned on, the screen shows the main page. Press EDID to enter the EDID setup page. EDID 2. SELECT : When you enter, EDID mode selection will show on the top. DES is an abbreviation for destination while SRC for source. Pressing source keys 1 and 2 enable you to select the 8 EDID modes. (See page 11) Pressing destination keys will enter learning mode. (See page 12) 3.
EDID FUNCTION EDID function : 7x Embedded EDID Modes Mode 1. FSS (Fast Speed Start) Fast Speed Start mode shortens the startup time of the switcher. Selecting this mode does not force the EDID setup to be cancelled. Users may first select one EDID mode from mode 2 to 8, and then select mode 1 for fast speed start. Mode 2. H24-3D (1080p-24 bits) Audio Support: PCM 2CH Mode 3. H24-3D-M (1080p-24 bits) Audio Support: MAT(MLP) 7.1CH, PCM2CH, One Bit Audio 2CH, AC-3 5.1CH, DTS5.1CH, PCM7.
EDID FUNCTION EDID FUNCTION : LEARNING Learning EDID EDID Single Destination to Single Source Destination 1 thru 16 Source 1 thru 16 Enter Copy the EDID of a single destination device and pass it to a single source. The source device will output video and audio according to the EDID of the destination. 1. Enter EDID setup page. 2. Choose one destination Example: Select Destination 3 3.
EDID FUNCTION EDID FUNCTION FOR HDMI MATRIX SWITCHER Learning Auto Mode Definition Let the source(s) learn the EDID from a single source and output video/audio accordingly. Let all the sources output the highest common resolution of all the connected destination devices. Operation Select a destination first and then select the desired sources. Use source button 1 or 2 to switch between EDID modes and select mode number 8.
EDID FUNCTION Q&A Q. Must a destination device display video and sound based on its own EDID? No. A destination device does not have to display its native resolution. Through the EDID learning function, a destination device can display based on the EDID of another destination, assuming there is no capability issue. Take the following 8x8 switcher for example. Suppose all the destination and source ports are connected.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR transmitters (SB-101) and IR receiver (SB-100) with SB-6335T & SB-6335R to control a projector. NOTE: 1. IR Control Projector Over HDBaseT Extender: SB-6335 HDBaseT Transmitter SB-6335R HDBaseT Receiver 2. RS-232 Control 3. External IR Remote. 4. IR Extender Transmitter : SB-101 IR Transmitter(300M), SB-101C (2M). 5. IR Extender Receiver : SB-100 IR Receiver (300M), SB-100C (2M).
TYPICAL APPLICATION INSTALLING DIAGRAM Example connection using IR transmitters (SB-101) and IR receivers (SB-100) with SB-6335T and SB-6335R to control a satellite receiver. NOTE: 1. IR Control Satellite Receiver Over HDBaseT CAT6/6a/7 extender from room: SB-6335 HDBaseT CAT5e/6/7 Transmitter SB-6335R HDBaseT CAT5e/6/7 Receiver 2. Audio Extractor To Recode Audio : SB-5609 HDMI Audio Extractor. 3. Control HDMI ARC: SB-5610 ARC Control Box. 4. IR Extender Transmitter : SB-101 (300M) Transmitter, SB-101(2M).
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
ETHERNET SERIAL INTERFACE ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION -2.0 COMPATIBLE RS-232 SERIAL INTERFACE Pin RS-232 Definition 1 -------- Not used 2 TX Transmitter 3 RX Receiver 4 -------- Not used 5 GND Ground 6 -------- Not used 7 -------- Not used 8 -------- Not used 9 -------- Not used RS-232 PROTOCOL COMMANDS (RS-232 Control driver V2.0.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM EDIA AUDIO A ND V IS UA L 1399 Wildfire Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
