SB-8811 INSTRUCTION MANUAL 8x8 DVI HDTV Video Matrix Routing Switcher
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS FULL HD DVI Matrix Switcher Series Thank you for purchasing the SB-8811 DVI Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher. CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 FEATURES & SPECIFICATIONS...................................... 2 FRONT PANEL ..........................................................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • • • • • • 8x DVI digital source devices matrix switched to 8x DVI devices DVI digital video w/embedded audio, DVI format and CEC/HDCP 2.0 compliant (7) function key control and worldwide (4) EDID modes for HDTV resolutions Link speeds of up to 6.
FRONT PANEL FRONT PANEL 1. POWER SWITCH: The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY: Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL 9 FUNCTION KEY - OFF 10. FUNCTION KEY - RECALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - MEMORY 13. FUNCTION KEY - LOCK 14. FUNCTION KEY - EDID The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Configure desired matrices. - Press MEMORY button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER to ready memory location. - Or press MEMORY again to cancel operation. Operation completes.
BACK PANEL BACK PANEL 1. DC POWER INLET: The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive). Power Jack: 2. IR EXTENDER CONTROL: Support one of IR Extender Extend IR Extender Jack: 3.
REMOTE CONTROL Before making any connections to the SB-8811. Observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%) • Ensure that the power switch is OFF • Ensure that all system grounds (earth) are connected to a common point.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC Standard) HOW TO SETUP IR CODES : CUSTOM CODE : 33CC POWER ON : 33CC A15E POWER OFF : 33CC A25D ALL : 33CC B04F OFF : 33CC B14E LOCK : 33CC B54A RECALL : 33CC B24D MEMORY : 33CC B44B ENTER : 33CC B34C PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 33CC DESTINATION #2 : 33CC DESTINATION #3 : 33CC DESTINATION #4 : 33CC DESTINATION #5 : 33CC DESTINATION #6 : 33CC DESTINATION #7 : 33CC DESTINATION #8 : 33CC 10
EDID FUNCTION IR REMOTE CUSTOM AND DATA CODES (NEC Standard) EDID Setup To change the EDID setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION EDID function : 4x Embedded EDID Modes Mode 1. FSS (Fast Speed Start) Automatic capture most suitable EDID from Destination to Source. Mode 2. 1280x1024-60Hz (DVI-D) DVI Support : DVI-D 1280x1024 - 60Hz Mode 3. 1920x1200-60Hz (DVI-D) DVI Support : DVI-D 1920 x 1200 - 60Hz Mode 4. AUTO All Outputs will be set to the highest common resolution of all connected display devices.
EDID FUNCTION EDID function for DVI Matrix Switcher EDID status To view the current EDID status. Step 1. Press EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2. Press EDID button To exit. How to setup FSS Function Learning EDID from Destination to Source Step 1. Press the Destination #1~8 button row Then Press the Source #1~8 button row To setup and Install all devices. Step 2.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335T & SB-6335R to control a projector. NOTE: 1. IR Control Projector Over HDBaseT™ Extender: SB-6335T HDBaseT™ Transmitter SB-6335R HDBaseT™ Receiver 2. Preview Output : Picture as same OUTPUT-1 3. RS-232 Control 4. External IR Remote. 5. IR Extender Transmitter : SB-101 IR Extender Transmitter. 6.
TYPICAL APPLICATION INSTALLING DIAGRAM Example connection using IR transmitters (SB-101) and IR receivers (SB-100) with SB-6335T and SB-6335R to control a satellite receiver. NOTE: 1. IR Control Satellite Receiver Over HDBaseT™ CAT6/6a/7 extender from room: SB-6335 HDBaseT™ CAT5e/6/7 Transmitter SB-6335R HDBaseT™ CAT5e/6/7 Receiver 2. Audio Extractor To Recode Audio : SB-5609 DVI Audio Extractor. 3. Control HDMI ARC: SB-5610 ARC Control Box. 4. IR Extender Transmitter : SB-101 IR Extender Transmitter. 5.
IR EXTENDER 1. SB-100 IR 300M Receiver Switcher IR EXT. In Cable (3C) Distance: Max.300M IR Receiver (SB-100) IR PN#: SW-XXXX R oHS /95/E C IR E XT. in RS - 232 IR EXT .
IR EXTENDER 1. SB-101 IR 300M Transmitter Device DC 12V Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set SB-101 Maximum Distance ~ 984 feet (300M) 2.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION -2.0 COMPATIBLE RS-232 SERIAL CONNECT Pin RS-232 Definition 1 ------ Not used 2 TX Transmitter 3 RX Receiver 4 ------ Not used 5 GND Ground 6 ------ Not used 7 ------ Not used 8 ------ Not used 9 ------ Not used RS-232 PROTOCOL COMMANDS (RS-232 Control driver V2.0.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
