M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5645LCM-CT 4x4 HDMI OVER CAT6 MATRIX SWITCHER 4x4 HDMI OVER CAT6 MATRIX SWITCHER HDMI Over CAT6 Matrix Switcher Series Thank you for purchasing the SB-5645LCM-CT 4x4 HDMI Over CAT6 Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this 4x4 HDMI Over CAT6 Matrix switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ............................................................... 1 FEATURES & CONTENTS ................................................ 2 SPECIFICATIONS .............................................................3 FRONT PANEL ..................................................................4 REAR PANEL ....................................................................7 REMOTE CONTROL ........................................................
FEATURES Based on HDBaseT; bi-directional IR, RS-232, Multi format Audio, Ethernet and full resolution HD Video all, signals over CAT5e/6/7 cable. FEATURES • 4x HDMI source devices matrix switched to 4x HDMI and 4x CAT5e/6/7 Extender output devices. • Application IR enabled by products designed using HDBaseT Specifications, RS-232, Multi Audio Format and HD Video Signals over CAT5 e/6/7 Cable • HDMI digital Video with embedded Audio, DVI format and CEC/HDCP 2.
SPECIFICATIONS SPECIFICATIONS • • • • • • • • • • • • • • • • • • • • • • Type of Switcher: 4x HDMI inputs To 4x HDMI and 8x CAT5e/6/7 Outputs Matrix Switcher HDMI Support: HD 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4a formats HDCP / CEC Support: HDCP 2.0 Compliant, CEC Compliant Video Bandwidth: Double Data Rates: 225Mhz, Total 6.75Gbps bandwidth Digital Video Support: HD: 480i / 480p / 720p / 1080i / 1080p up to 36bit deep color Digital Audio Support: • Multi Audio Formats 5.1 / 7.
FRONT PANEL FRONT PANEL 1. POWER SWITCH The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 4 LCM illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 4. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9. FUNCTION KEY - OFF Disables (mute) video to selected channels.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - RECALL The system will show previously stored presets, up to a total of 8. Presets are stored in local memory using Source keys 1 thru 4 or Destination keys 1 thru 4 as the memory preset location. - Configure desired matrices.. - Press RECALL button. - Press 1 thru 4 on either Source or Destination row. - Press ENTER The pre-set configuration will execute. Operation completes. Note : Operation will abort if no keys are pressed within 5 seconds. 13.
REAR PANEL REAR PANEL 1. DC POWER INLET The Switcher is fitted with a DC power plug input connector. Ensure that the outlet type is approved and sufficient to carry current connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive). Power Jack: DC Jack - Inner OD ᴓ 2.1mm (+ ) Outside OD ᴓ 5.5mm (GND) Power input - 12VDC, 5A 2. IR EXTERNAL IN (EXT. IR TO CONTROL SWITCHER) Supports one of IR Extender. Extend distance maximum 300 M / ~1000 ft.
REAR PANEL REAR PANEL 6. RS-232- 1,2,3 & 4 CONNECTION TO CONTROL ROOM 4x RS-232 control port to allow for interfacing to a PC. Such as a computer or touch panel control, to the switcher via this DB-9pin female connector for serial RS-232 control. Remote port : DB-9pin Female connector 7. OUTPUT - 1,2,3 & 4 CAT CATx Transmitter extends a signal link of HDMI / RS-232 / IR Remote to this RJ-45 female connector via CAT5e/6 cable.
REMOTE CONTROL Before making any connections to the SB-5645LCM-CT. Observe the following: > Ensure the main voltage supply matches the label on the supplied plug- Pack (+/- 10%) > Connect all audio video sources and destination equipment > Ensure that the power switch is OFF > For each destination output select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote control. Or through the RS-232 serial communications port.
REMOTE CONTROL IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES CUSTOM CODE : 1CE3 DATA CODE : POWER ON : 1CE3 POWER OFF : 1CE3 ALL : 1CE3 OFF : 1CE3 EDID : 1CE3 LOCK : 1CE3 RECALL : 1CE3 MEMORY : 1CE3 ENTER : 1CE3 A15E A25D B04F B14E B748 B54A B24D B44B B34C PRESS TV DESTINATION - # then PRES AV SOURCE - # DESTINATION #1 : 1CE3 10EF DESTINATION #2 : 1CE3 20DF DESTINATION #1 : 1CE3 30EF DESTINATION #2 : 1CE3 40DF SOURCE #1 : 1CE3 SOURCE #2 : 1CE3 SOURCE #3 : 1CE3 SOURCE #4 : 1CE3 01FE
REMOTE CONTROL ROOM REMOTE CONTROL #1 ~ #4 CUSTOM CODE AND DATA CODES IR CUSTOM AND DATA CODES (NEC Standard) PRESS Number To Select SOURCE CUSTOM CODE : 1CE3 IR-01 DATA CODE: SOURCE #1 : 1CE3 SOURCE #2 : 1CE3 SOURCE #3 : 1CE3 SOURCE #4 : 1CE3 11EE 12ED 13EC 14EB IR-03 DATA CODE: SOURCE #1 : 1CE3 SOURCE #2 : 1CE3 SOURCE #3 : 1CE3 SOURCE #4 : 1CE3 31CE 32CD 33CC 34CB 11 IR-02 DATA CODE: SOURCE #1 : 1CE3 SOURCE #2 : 1CE3 SOURCE #3 : 1CE3 SOURCE #4 : 1CE3 21DE 22DD 23DC 24DB IR-04 DATA CODE: SOURCE #1
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 RS-232 SERIAL INTERFACE Pin RS-232 Definition 1 -------- Not used 2 TX Transmitter 3 RX Receiver 4 -------- Not used 5 GND Ground 6 -------- Not used 7 -------- Not used 8 -------- Not used 9 -------- Not used RS-232 PROTOCOL COMMANDS ( RS-232 Control driver V2.
EDID FUNCTION EDID FUNCTION SETUP EDID Setup To change the EDID setup Step 1 . Press the EDID button The display will show the currently selected EDID mode Step 2 . Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. Step 3 . Press the ENTER button To set EDID mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID. For example; When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the EDID data cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you want to remove the learning EDID memory from EPRPM. EDID FUNCTION : 8X EMBEDDED EDID MODES EDID Function 8x Embedded EDID Modes Mode 1.
EDID FUNCTION EDID FUNCTION FOR HDMI MATRIX SWITCHER Learning EDID Single to Single Example : Learn Destination #4 EDID To Source #2. Step 1 . Press EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2 . Press the Destination #4 button row Copy the Destination #8 Display EDID. Step 3 . Press the Source #2 button row Learning the Destination #4 EDID To Source # 2. Step 4 . Press ENTER button To confirm entries.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335T & SB-6335R to control a projector. NOTE: 1. Control Projector Over CAT5e/6/7 Extender: SB-6335T HDMI CAT5e/6/7 Transmitter SB-6335R HDMI CAT5e/6/7 Receiver 2. Projector RS-232 Control by a PC. 3. Projector IR via CAT6 Transmitter (To projector). 4. IR Extender Transmitter : SB-101 IR Extender Transmitter 5.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using SB-6335T HDBaseT IR Transmitters (SB-101) and SB-6335R HDBaseT IR Receiver to control a Satellite Receiver IR Remote. NOTE : 1. IR Control Satellite Receiver Over HDBaseT CAT5e/6/7 Extender from room: SB-6335T HDBaseT CAT5e/6/7 Transmitter SB-6335R HDBaseT CAT5e/6/7 Receiver 2. Destination DEVICE RS-232 Control: Via SB-6335T RS-232 in 3. IR Extender Transmitter: SB-101 IR Extender Transmitter 4.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using Audio Extractor To Re-code Audio (SB-5609) or to control ARC (SB-5610) and Extend the HDMI signal via HDBaseT Transmitter to IR Receivers (SB-6335R) with SB-5645LCM-CT to extend 100M distance between switcher and destination. NOTE : 1. Audio Extractor To Re-code Audio: SB-5609 HDMI Audio Extractor 2. Control HDMI ARC: SB-5610 ARC Control Box 3. RS-232 Control Via a PC. 4. Switcher IR External port: Via SB-100 IR Extender Receiver 5.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
