M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5688LCM 8x8 HDMI MATRIX SWITCHER 8x8 HDMI Matrix Switcher HDMI Matrix Switcher Series Thank you for purchasing the SB-5688LCM HDMI Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMI Matrix switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION & CONTENTS ................................................. 1 FEATURES & SPECIFICATIONS .............................................. 2 FRONT PANEL ........................................................................... 3 REAR PANEL ............................................................................ 6 REMOTE CONTROL ...................................................................7 EDID FUNCTIONS ..................................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • • • • 8x HDMI with DVI-Audio source devices matrix switched to 8x HDMI output devices. HDMI digital Video w/ embedded HDCP, DVI format and CEC/HDCP 2.0 compliant Worldwide control EDID modes for HD Video resolutions. Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a 3D formats.
FRONT PANEL FRONT PANEL 1. POWER SWITCH The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9. FUNCTION KEY - LOCK Disables (mute) video to selected channels.
FRONT PANEL FRONT PANEL 12 FUNCTION KEY - MEMORY The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Configure desired matrices. - Press MEMORY button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER to ready memory location. - Or press MEMORY again to cancel operation. Operation completes. Note : Operation will abort if no keys are pressed within 5 seconds.
REAR PANEL REAR PANEL 1. DC POWER INLET The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 5A Max (Center pin positive). 2. IR EXTENDER CONTROL Support one of IR Extender (IR input) Extend distance maximum 984 ft (300M) Note: DO NOT install or remote this connection with the power ON. Power Jack: DC Jack - Inner OD O 2.
REMOTE CONTROL Before making any connections to the switcher. Observe the following: > Ensure the mains voltage supply matches the label on the supplied plug-pack (+/- 10%) > Connect all audio video sources and destination equipment > Ensure that the power switch is OFF > For each destination output select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote control. Or through the RS 232 serial communications port.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : ALL OFF EDID LOCK RECALL MEMORY ENTER CUSTOM CODE : 09F6 POWER ON : 09F6 A15E POWER OFF : 09F6 A25D : 09F6 B04F : 09F6 B14E : 09F6 B748 : 09F6 B54A : 09F6 B24D : 09F6 B44B : 09F6 B34C PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 09F6 DESTINATION #2 : 09F6 DESTINATION #3 : 09F6 DESTINATION #4 : 09F6 DESTINATION #5 : 09F6 DESTINATION #6 : 09F6 DESTINATION #7 : 09F6 DESTINATION #8 : 09F6 SOURCE #
EDID FUNCTION EDID FUNCTION SETUP EDID Setup To Change the EDID Setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION EDID FUNCTION : 8X EMBEDDED EDID MODES Mode 1. FSS (Fast Speed Start) Mode 5. H36-3D-M (1080p-36 bits) Fast Speed Start mode shortens the startup time of the switcher. Selecting this Video Support : All resolutions up to and including 1080p. mode does not force the EDID setup to be cancelled. Users may first select Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 one EDID mode from mode 2 to 3, and then select mode 1 for fast speed start. 5.1CH, DTS 5.1CH, PCM 7.
EDID FUNCTION EDID FUNCTION FOR HDMI MATRIX SWITCHER EDID Status To view the current EDID status. Step 1. Press EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2. Press EDID button To exit. How to setup FSS Function Fast Speed Start Step 1. Press the Destination #1~8 button row Then Press the Source #1~8 button row To setup and Install all devices. Step 2. Press EDID button Select a optimum status of Embedded EDID mode. Step 3.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR Transmitters (SB-101) and IR Receiver (SB-100) with SB-6335T & SB-6335R to control a projector. NOTE: 1. IR Control Projector Over HDBaseT Extender: SB-6335 HDBaseT Transmitter SB-6335R HDBaseT Receiver 2. Preview Output : Picture as same OUTPUT-1 3. RS-232 Control 4. External IR Remote. 5. IR Extender Transmitter : SB-101 IR Extender Transmitter. 6. IR Extender Receiver : SB-100 IR Extender Receiver.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using IR Transmitters (SB-101) and IR Receivers (SB-100) with SB-6335T and SB-6335R to control a Satellite Receiver. NOTE: 1. IR Control Satellite Receiver Over HDBaseT CAT5e/6/7 Extender from room: SB-6335 HDBaseT CAT5e/6/7 Transmitter SB-6335R HDBaseT CAT5e/6/7 Receiver 2. Audio Extractor To Recode Audio : SB-5609 HDMI Audio Extractor. 3. Control HDMI ARC: SB-5610 ARC Control Box. 4. IR Extender Transmitter : SB-101 IR Extender Transmitter. 5.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION -2.0 COMPATIBLE RS-232 SERIAL INTERFACE Pin RS-232 Definition 1 -------- Not used 2 TX Transmitter 3 RX Receiver 4 -------- Not used 5 GND Ground 6 -------- Not used 7 -------- Not used 8 -------- Not used 9 -------- Not used RS-232 PROTOCOL COMMANDS (RS-232 Control driver V2.0.
ETHERNET SERIAL INTERFACE ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
