Troubleshooting guide

ENGLISH
48
SETTING THE SYSTEM
• AMP (AMP ASSIGN) : To assign the surround back channels' power amplifier correctly depending on how to use the speakers.
• TONE : To adjust the tone (bass and treble) as desired.
• PWR-M (POWER MANAGER) : To set the POWER MANAGER mode depending on how to use the VuNow for power saving.
■When selecting the AMP ASSIGN
• The surround back channels' power amplifier can drive the surround back speakers or the ROOM 2 speakers. Depending on
how to use the speakers, you should assign the power amplifier correctly. (For details, refer to “CONNECTING SPEAKERS” on
page 8 and “CONNECTING ROOM2 SPEAKERS” on page 9.)
BACK (SURROUND BACK) : To drive the surround back speakers when connecting the SURROUND BACK/ROOM2 channels
to them.
R2 (ROOM2) : To drive the ROOM2 speakers when connecting the SURROUND BACK/ROOM2 channels to them.
■When selecting the TONE
OFF : To listen to a program source without the tone effect. (“DIR” lights up.)
↕
ON : To adjust the tone for your taste. (“DIR” goes off.)
◆When the TONE CONTROL is set to ON to adjust the tone (bass and treble)
①. Press the ENTER button to enter the tone adjustment mode.
• Then “TRE ~” will be displayed.
②. Press the CURSOR UP/DOWN buttons to select the desired tone mode.
③. Press the CURSOR LEFT/RIGHT buttons to adjust the selected tone as desired.
• The tone level can be adjusted within the range of -10 ~ +10 dB.
• In general, we recommend the bass and treble to be adjusted to 0 dB (flat level).
• Extreme settings at high volume may damage your speakers.
• To complete tone adjustment, repeat the above steps ② and ③.
■When selecting the POWER MANAGER
→ OFF : To turn on the VuNow circuitry constantly when this unit is turned on.
↕
60 / 30 / 10 : If the specified period of time elapses after selecting the input source other than VuNow, the VuNow circuitry will
↕ be turned off.
→ ON : To turn on the VuNow circuitry when the VuNow is selected as an input source.
1. Press the CURSOR UP/DOWN buttons to select the desired item.
2. Press the CURSOR LEFT/RIGHT buttons to set the selected item as desired.
SET RMEQ
MLT ROOM
AMP : BACK / R2
TONE : OFF / ON
PWR-M : OFF / 60 / 30 / 10 / ON
F : LARGE / SMALL
C : LARGE / SMALL / NO
S : LARGE / SMALL / NO
SB : LX2 / LX1 / SX2 / SX1 / NO
SW : YES / PLUS / NO
TRE : 0 / -10 ~ +10
BASS : 0 / -10 ~ +10
ROOM2 : OFF / ON
R2 : TUNER / CD / AUX / F.AUX / VIDEO 1/ V2/IPD
R2VOL : 40 / MIN(0) ~ MAX(80)
SPK CFG
X.OVER X.OVER : 50 / 80 / 100 / 150 / 200
CH LEVEL
DISTANCE
T. TONE : M / A
L : 0 dB / -15 ~ +15
C : 0 dB / -15 ~ +15
R : 0 dB / -15 ~ +15
SR : 0 dB / -15 ~ +15
SBR : 0 dB / -15 ~ +15
SBL : 0 dB / -15 ~ +15
SL : 0 dB / -15 ~ +15
SW : 0 dB / -15 ~ +15
L : 10.0 FT / 0.1 ~ 30.0
C : 10.0 FT / 0.1 ~ 30.0
R : 10.0 FT / 0.1 ~ 30.0
SR : 10.0 FT / 0.1 ~ 30.0
SBR : 10.0 FT / 0.1 ~ 30.0
SBL : 10.0 FT / 0.1 ~ 30.0
SL : 10.0 FT / 0.1 ~ 30.0
SW : 10.0 FT / 0.1 ~ 30.0
↕
R-904N(A)_ENG_091007:R-904N(A) 2009-10-14 오후 1:53 페이지 48
Meijer.com