LA vehicle land&air INSTRUCTIONS FOR USE A90 FORBIDDEN: Special design for indoor & outdoor, please keep it away from obstacle.
CONTENT 1.0 Disclaimer & Warnings 1 2.0 Safety Guidelines 2-4 3.0 Packing list 4 4.0 Drone’s Details 5 5.0 Transmitter Functions 6 6.0 Joystick Mode 6 7.0 Installation 7-9 8.0 Charging 9 9.0 Operation Guide 9.1 Pairing 10 9.2 Calibrating the Gyro 11 9.3 Taking-Off / Landing Method 12 10.0 Function Details 10.1 Emergency Stop 12 10.2 Trimming 13 10.3 Headless Mode 14 10.4 Speed Switch 15 10.5 360 Flips 16 10.6 LED ON/OFF 17 10.
1.0 DISCLAIMER & WARNINGS 1. Please read this disclaimer, warnings and safety guidelines carefully before using our product. This product is not recommended for people under the age of 14. By using this product, you hereby agree to this disclaimer and signify that you have read it fully. You agree that you are responsible for your own conduct and any damage caused while using this product, and its consequences.
2.0 SAFETY GUIDELINES 2.1 Check Before Use (1). This product is not a toy, but a high precision drone that integrates various electronic stability and control mechanisms. Please be sure to set up this drone carefully and correctly to ensure safe, accident-free operation. (2). Please be sure that the batteries of the drone and transmitter are clean, undamaged and have enough power. (3). Please be sure that all the propellers are undamaged and are installed in the right orientation. (4).
2.3 Use of Battery (1) Please ensure the batteries are fitted in the correct orientation as shown in the instruction manual. (2) Avoid short circuits by fitting the batteries incorrectly, and do not crush the batteries as this may cause the risk of an explosion. (3) Do not mix new and old batteries as this can lead to a poor performance of the product. (4) Dispose used batteries carefully. (5) Please keep dead batteries away from heat and fire.
2.4 Maintenance 1. Clean the product after each use with a clean, soft cloth. 2. Avoid prolonged exposure to direct sunlight and avoid the buildup of heat on the drone or batteries. 3. This device is not waterproof and must not be submerged or subjected to water under any circumstance. Failure to keep the device completely dry will result in failure and permanent damage to the unit.
4.0 DRONE’S DETAILS Propeller A Propeller B Propeller B Propeller A It is crucial that all the propellers are installed in the correct position WARNING (Pay attention to the letter A or B printed underneath each propeller).
5.0 TRANSMITTER FUNCTIONS Indicator Light Speed Switch Flip Trim Headless Left Joystick Right Joystick LED ON/OFF One Key Take-off One Key Land (Short Press) Emergency Stop (Long Press) Trim Power Switch Calibrating the Gyro (Short Press) 6.
7.0 INSTALLATION 7.1 Drone Battery Installation: Push down to open the battery compartment, align the battery plug with the drone plug and connect them. WARNING Pay attention to the positive and negative directions of the battery plug when connecting the battery. The plug in the wrong direction cannot be connected. After connecting the battery, place the battery in the drone battery compartment; close up the battery compartment cover and lock it.
7.2 Propellers HEAD Installation: As shown above, connect each propeller to its corresponding motor shaft, either position "A/B", then lock the propeller to the motor shaft. To remove the blades: insert the blade driver diagonally into the bottom of the blade with downward pressure. Find the corresponding type of blades (A to A, B to B), and press the blades vertically to the motor shaft until the blades are pressed to the level of the protection rings.
7.3 Transmitter Battery Battery Cover 3 x AAA batteries (not included) Always use alkaline batteries, never mix old and new batteries. WARNING 1. Unscrew the battery cover, press and slide the battery cover out, and insert 3 x AAA batteries(not included), make sure to insert them following the correct polarity as shown. 2. Re-attach the battery cover. 8.0 CHARGING 8.1 Drone Battery USB Adapter (5V@0.5-2.
1. Plug the USB charging cable into a USB charging port on the computer, power bank or USB adapter (5V @ 0.5 to 2.0A ). 2. Connect the wire of battery with USB charging cable. 3. Charging time: about 60-70 minutes. 4. The red indicator light on the USB charging cable will turn off when the battery is under charging; and will turn on when the battery is fully charged. Before charging, please read the instruction of the "2.3 Use of WARNING Battery" section of the "Safety Guidelines" carefully! 9.
HEAD (3). Place the drone on a flat and level surface with the head forward and the tail facing towards the operator. (4). Slowly push the left joystick of the transmitter up to the top and transmitter will beep once and then pull down to the bottom and transmitter will beep once again. After pairing, the power indicator of the remote control will be solid, and the LED lights of the drone will appear "flickering". Up Down 9.
9.3 Taking-Off / Landing Method 1.2m Short Press One Key Take-Off One Key Land Method 1: Short press the one key take-off/land button “ ”, the drone will automatically take off and hover at an altitude about 1.2 meter. Short press the one key take-off/land button “ ” again, the drone will land slowly until landing. Method 2: Push the left joystick up until the propellers of drone rotate without taking off and then push up the left joystick again to take off. Pull the left joystick down until landing.
10.2 Trimming F/B Sideward Fly Trim 1- Forward trim 2- Backward trim 3- Left trim 4- Right trim If the drone sways in an unprompted direction, use the trim buttons to correct the flight: L/R Sideward Fly Trim If the drone drifts left, short press down the right joystick while pushing the direction joystick right to balance the drone; If the drone drifts right, short press down the right joystick while pushing the direction joystick left to balance the drone.
10.3 Headless Mode Short press the headless button Short press the headless button , the remote control will beep once, and at the same time all the LED lights of the drone body will flash twice simultaneously then break for 0.5 seconds, then flash twice and then break for 0.5 seconds, thus the drone has entered headless flight mode.Short press down the left joystick again to exit headless mode.
Under Headless Mode, the forward direction is the direction that the head of drone faces when the drone takes off. In order to make sure the pilot can tell drone's direction, we recommend that pilots to stay in the same orientation as the drone head faces when the drone takes off. If so, when the pilot pushes the direction joystick forward, the drone will fly forward. If the pilot pushes the direction joystick backward, the drone will fly towards him/her.
o 10.5 360 Flips Short Press Perform 360 flips by pressing the "flip" button and immediately operate the right joystick in the desired direction. 10 Feet When you get familiar with all the functions of the drone, you can try this amazing flip mode. When you fly the drone at least 10 feet, press the 360° Flip button on the upper right of the transmitter, then push the right joystick Forward/ Backward or Left/ Right, and the drone will do a flip towards the corresponding direction.
10.6 LED ON/OFF Long Press Press the LED button to turn off/on the LED lights of the drone. 10.7 Race On Land Mode Forward 1. When the drone is flying in the air, after landing the drone to the level ground, push the right joystick forward, and the drone will drive forward. Turn left Turn right 2. When the drone is driving forward on the level ground, turning the left joystick to the left will turn the drone to the left, and turning the left joystick to the right will turn the drone to the right. 3.
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
1. ALL MARVELENT PRODUCT CARRIES A 100% SATISFACTION GUARANTEE. 2. STAY UP-TO-DATE ON WHAT’S NEW FROM MARVELENT. 3. ALL THE PRODUCTS COVERED BY UNCONDITIONAL LIFETIME WARRANTY WHEN YOU COMPLETE THE REGISTRATION PROCESS.
