User's Manual

Serial
number
function Operation Use Function Results
1 Smart boot
The headset is taken out of the charging box and
automatically turned on.
Blue light flashes with a power-on tone
2
Smart shutdown
The headset is automatically turned off by putting it
into the charging box.
Blue light flashes
3
Shut down
Headphones long press for 5 seconds to shut down Blue light goes off
4
Boot on
Headphones long press for 5 seconds to shut down Blue light flashes with a power-on tone
5
Entering the interconnect mode
After the headset is removed from the charging box,
it automatically enters the blue light flashing state and has
a voice prompt.
Blue light flashes with ready to pairing tone
6
Paired left and right headsets
successfully
The right earphone blue light flashes quickly, the left
earphone blue flashes slowly, and there is a voice prompt.
Voice prompts
7
Mobile phone pairing success
The headset is successfully paired with the phone, the blue
light flashes slowly, and there is a voice prompt.
Voice prompts
8
Bluetooth disconnect
The headset is disconnected from the mobile phone Bluetooth,
the blue light flashes quickly, and there is a voice prompt;
after 5 minutes of disconnection, the headset will
automatically shut down and have a voice prompt.
There is a tone and there is a disconnect tone
9
Play, pause music Connection status, click the touch button Start playing/pausing music
10
Song switching up and down
When entering the music play mode, double-click the left
earphone touch button area to switch to the previous track;
double-click the right earphone touch button area to switch to
the next track;
11
Volume addition and
subtraction
When entering the music playback mode, press and hold the left
earphone to touch the button area to decrease the volume; long
press the right earphone to touch the button area to increase
the volume;
12
Answer the call
Connection status Click the R headset or L headset touch
button
Have a tone and answer the call
13
hang up the phone
Click the R headset or the L headset touch button during the
call.
Have a tone and hang up
14
Reject
Press and hold the R headset or L headset touch button
in the incoming call state.
There is a tone and reject the call
15
Low electric tone
Report low power when the voltage is low (reported every 30
seconds)
Voice prompts
16
IPHONE power display
Bluetooth is connected to Bluetooth, and the iPhone has a
power indicator.
17
IPHONE volume synchronization
The Bluetooth connection is successful and the machine volume
is synchronized with the phone volume.
18
Automatic connection
After the connection is successfully restarted, the Bluetooth
headset automatically connects back to the Bluetooth device.
"Beep" and have a successful pairing voice
prompt
19
Remote disconnection
After disconnecting from a long distance, the headset will
automatically return to the headset within 5 meters within 3
minutes.
"Beep" and have a successful pairing voice
prompt
20
Charging automatic shutdown Play status, sleep, standby, charging will be turned off Voice prompt
21
Wake up Siri
Double-click the touch button area of the right earphone
or the left earphone
22
Breathing light
Connect the mobile phone Bluetooth music to play the full
circle light effect for the breathing light effect; long press
the earphone touch button area for about 3 seconds and the
prompt tone "beep" will turn off the breathing light, if you
need to re-open the breathing light effect, then press and
hold for about 3 seconds And there is a "beep" sound.
"Beep"
22
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipmen t generates uses and can
radiate radio frequency energy and, if not installed and u sed in a ccordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this eq uipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation b etween the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced ra dio/TV technician for help.
The device has been evaluated to meet general RF exposu re requirement. The device can be used in
portable exposure condition without restriction.
Bluetooth headset is not in charge state
User's manual