YN622C II 622 560-RX OFF User Manual 用户手册
Contents 注意事项 General Description . . . . . . . . Function Introduction . . . . . . . Supported Functions List . . . . . Compatibility List . . . . . . . . . Name of Parts . . . . . . . . . . Preparation Before Use . . . . . . Setting . . . . . . . . . . . . . Flash Awaking /Testing Flash . . . . Remote Control Mode . . . . . . . Mix Control Mode . . . . . . . . . Flash Triggering of Type B/C Camera . PC Port Triggering . . . . . . . . . References . . . . . . . . . . . Troubleshooting . . . . . . . . .
General Description This product is a wireless transceiver, transmitting & receiving mode will automatically switched. to express conveniently, in this user manual, it is called transmitter (master control unit) when being installed on the hot shoe of the camera, while it is called receiver (slave unit) when a flash is installed or connected.
Function Introduction Thank you for purchase the products of Yongnuo firstly. The new upgrade version YN622C II can set to "622" or "560-RX" communication mode through the power switch, supports receiving the trigger signal of the YN560-TX/RF605(603 mode)/RF603(II) series products, with multi aspects improved, equipped with quick lock design and supports USB firmware upgrade.
Supported Functions List Quick lock design Supports USB firmware upgrade Supports "622" communication mode,"560-RX" communication mode Compatible flash mode: E-TTL (II)/ Manual/ Multi Compatible Shutter sync: 1st curtain, 2nd curtain, high speed sync (HSS/FP), Max 1/8000s sync speed Control remote flash using camera's flash control menu screen(Remote Control Mode) Support E-TTL / Manual/ Multi flash mode mix using(Mix Control Mode) Flash on hot-shoe of transmitter supports ETTL Support Fl
Compatibility List Functions supported by the product depend on the camera and flash used. According to different types of cameras, in this user manual, the EOS DSLR camera with external flash(speedlite) control menu is called type A camera; while EOS DSLR camera without external flash control menu is called type B camera; other camera brands with standard hot-shoe is called type C camera.
Name of Parts Indicator Blinking Keep Lighting Channel Indicator Communicating （Remote control mode） Firing group or receiving group Mix Control Mode State Indicator(green) TX Communicating(622) Testing Communicating State Indicator(red) RX Communicating(622) Standby State Group Indicator State Indicator(orange) RX Communicating(560-RX) Testing Communicating Standby State ※The protective film can be torn out. Q R 622 560-RX OFF K A AF assist beam emitter(p.24) J State indicator(p.
Preparation Before Use 1. Installing the Batteries Open the cover and install two AA batteries (excluded)according to the + and - marks , rechargeable batteries of 1.2V can be used. When in low batter y, the status indicator light will blink(red) separately, at the moment need to replace batter y. ※ Remove the batteries when the product is not used for long time. ※ Please replace the both two batteries at the same time. 2.Attaching and Detaching the Transmitter 1).Attach the transmitter.
Preparation Before Use 3 . I n s t a l l F l a s h o n t h e H o t S h o e of t h e Transceiver (as Receiver) 1. Install the transceiver into the flash bracket or other fixing devices (Not included in the product box). 2.Make sure the mounting foot lock of the flash is released 3.Slide the flash’s mounting foot into the transceiver ’s hot shoe fully. 4.Lock the flash in place.
Setting 1.Power switch The YN622C II adopts 3 sections of power switch design. When it set in the “622” communication mode, the red indicator light will bright, when set in the “560-RX’ Red Indicator communication mode, the orange indicator (622mode) light will bright, “OFF”for power off. When it used with the YN622C series products, please set the power switch on “622”position,transmitting/receiving mode will automatically switched.
Setting 4.Flash Test Group Setting (Test + GP SET Button) Set flash testing group Type C camera uses the set firing group. YN622C Ⅱ 622 560-RX OFF 1. H o l d d o w n [ Te s t ] b u t t o n t h e n t h e g r o u p indicators will keep lighting, the flash on the receiver group having been selected will be woken up(p.10). 2. Hold down [Test] button and repeat to shortly press [GP SET] button, selected groups of receivers to testing flash, and there are totally 7 combinations. 3.
Flash Awaking and Testing Flash When half-pressing the shutter button of the camera, the hot-shoe flash on the receiver will be awakened. (for A/B type camera only) Under any connection type, [Test] button can be pressed to awaken and test the flash on the transceiver and other transceivers at the same channel. Test flash with the mode set by the flash, and under the mode of E-TTL it may fire in a lower output.
Remote Control Mode Remotely setting all the flashes through the external flash function setting (camera menu) of the camera, just likes the flash being directly installed on the camera. The settings of camera menu is prior, settings will upgraded to the receiver after pressing down camera confirmation button or half pressing shutter button without needing to operate the flash control panel, the flash’s screen will display the current setting. The setting varies depending on the cameras/flashes.
Automatic Flash (E-TTL II) Fully-automatic Flash Shooting 1. Select flash mode as E-TTL II mode. 2. Half press camera's shutter button to focus, and on the flash screen the aperture and effective range etc. parameters will be displayed. 3. Ensure that the subject is in the effective flash range, full press camera’s shutter button to shoot, the flash will be fire according to the setting. ※ Exposure lever increments may set to 1/3-stop via the camera.
Shutter Sync 1. 1st Curtain sync The normal flash sync. 2. 2nd curtain sync The flash fires right before the shutter closes, lower shutter speed needs to be used, support bulb 2nd curtain sync flash. ※Only when wireless flash function via the flash control menu is disable , the 2nd curtain sync can be use. 3. Hi-speed Sync(HSS/FP FLASH) The flash can sync with all shutter speeds when using HSS . The max speed is 1/8000s or 1/4000s（depends on the camera）.
