User's Manual

C01
User Manual
EN
AD
Control Button
Turn on Take earbuds out to turn on
Turn off Put back into charging case
to turn off
Play/Pause Press left or right power
button once
Volume - Hold left power button
Previous Press left power button twice
Pick up phone Press left or right power
button once
Hang up Press left or right power
button once
Reject incalling
hold and press any power
button for about 2s
Volume + Hold right power button
Next Press right power button twice
Charge
Charging Case Charge
Please use the charger with output of DC5V/1A.
You can use USB cable to charge the charging
case with computer or other devices which have
USB ports. (Please use factory-certified charger).
Earbuds Charge
Take out the earbuds from the charging case.
Or hold the power button for 3 seconds until
the blue indicators flash once while earbuds
are powered off.
Put the earbuds into the charging case, they
would turn off and star charging. Or disconnect
the Bluetooth, they would turn off in about
5 minutes.
Turn ON
Turn OFF
1. Put both earbuds in the charging case,
the indicator turns red when they are charging.
2. While in charging status, the red signal
light will stay solid.
3. The red signal light will turn blue and then
turn off when the earbuds are fully charged.
MIC
Left Right
Product Overview
L
M
S
Ear Cap
Charging Contact Pin
Charging Case
Indicator Light
Power Button / Indicator Light
We offer three different sizes of ear caps:
large, medium and small. Please try different
sizes of ear caps to find the right fit for you.
Ear Cap Options
Parameter specification
Version V5.2+EDR
Support A2DP,AVRCP,HFP,HSP
Transmission distance 10m
Frequency range 2.402GHz~2.480GHz
Hi-fi equipment Φ6mm*2
Impedance 16Ω
Standby time 70 hours
Talk time 4 hours
Music time 5 hours
Earbud battery capacity 55 mAh
Charging time 1 hour
Charging case battery capacity 400mAh
Charging case charging time About 1 hours
Weight(single earbud) 4.0 g
There is a built-in lithium battery in this
product. To avoid explosion, do NOT
expose the product to strong sunlight,
fire or throw it into fire.
Battery Warning ！
8.Please do not charge the product with the power
adapter of a current greater than 2A. Excessive current
flow could cause damage to the battery.
Signal transmission distance shown as
below:
√
×
≤10m Signals is in normal transmission.
10m Signals will be interrupted.
Attentions
1.Do not use corrosive liquid to clean this product.
2.Do not use this product under extreme circumstances
for temperature below -10 degree Celsius or above
60 degree Celsius .
3.To avoid explosion, please do not throw this product
into fire.
4.To avoid scratches, please do not touch the earbuds
with sharp objects.
5.Do not insert objects into the earbuds, otherwise it
would cause damage to the internal components.
6.Do not disassemble the earbud.
7.In case the earbuds run out of battery, please charge
the earbuds when it’s out of use for more than a month.
Settings
Bluetooth
C01
Bluetooth
Now discoverable as”Qi iPhone”.
MYDEVICES
To pair Apple Watch with your iPhone, go to the
Watch app.
Pairing Manual
Earbuds Manual
1.Take out the two earbuds from the charging
case and peel off the insulating film.
2.Put the two earbuds into the charging case
to charge ( the earbuds are in charging state).
3. Take out the two earbuds, they will turn on
and pair automatically and will be prepared for
pairing to the phone (the indicator will turn red
and blue alternately).
4. After successful paired, the master earbud
indicator turns red and blue alternately, the slave
earbud indicator goes off .
5.Turn on the Bluetooth function on your phone
and search【C01】and connect it.
6.After the earbuds successfully paired to the
phone, the indicators will go off.
Tips: If the earphones can't be found and not
in the pairing mode, you can double click any
earbud to enter the pairing mode.
Thanks for using our wireless electronic
products. For a good user experience, please
read the manual carefully before using the
products. Notice: To avoid unnecessary
troubles please do not disassemble these
products by yourself and use the standard
charger to charge.
IOS users and some of the Android users
can triple click the left earbud or right earbud
to turn on the Voice Assistant.
Siri and other Voice Assistant
1. Turn off the Bluetooth function of the
mobile phone.
2.Long press the headset for 3 seconds and
then let go, and then press one of the
headsets 4 times to clear the pairing.
3. Please delete all paired records on the
phone and re-search【C01】after clear
the pairing.
please restore factory setting!
FCC Caution