Motorized Treadmill Operating Instructions Manual Special tips: 1. Before installation and operation, please read this operation manual carefully. 2. Please save this manual for future reference. 3. Product may vary slightly from the item pictures due to model upgrades.
Content 1. Safety Precautions.........................................................................................1-3 2. Assembly Steps.............................................................................................4-8 3. Folding Steps...................................................................................................9 4. Grounding Methods........................................................................................10 5. Operation Instruction...............
IMPORTANT SAFETY INSTRUCTIONS WARNING - Read all instructions before using this treadmill. It is important your treadmill receives regular maintenance to prolong its useful life. Failing to regularly maintain your treadmill may void your warranty. Danger–To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to cleaning and/or service work.
IMPORTANT ELECTRICAL INFORMATION WARNING! 1) NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels. 2) NEVER operate treadmill on Generator or UPS power supply. 3) NEVER remove any cover without first disconnecting AC power. 4) NEVER expose this treadmill to rain or moisture.
ASSEMBLY INSTRUCTIONS When you open the carton, you will find the below spare parts: Spare parts list： NO. DES. Specification A Main Frame 1 B IPAD Holder 1 C15 Knob 2 C18 Safety Key 1 E18 Power Wire 1 E09 Remote Control 1 C34 Oil 1 FIXING TOOLS: 3 Nos.
ASSEMBLY STEP 1： EXPLODED DRAWING 4
ASSEMBLY STEP 2： Loosen Use the knob to loosen the screw,so that you can raise the handrail.
ASSEMBLY STEP 3: Raise the handrail,then tighten the knob.
ASSEMBLY STEP 4: Put the ipad holder into push into the bottom. the slot, then Push the clip inward, then pull out the Ipad holder.
ASSEMBLY STEP 5: Put the safety treadmill.
FOLDING INSTRUCTION 1: 9
GROUNDING METHODS This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
OPERATION GUIDE WINDOW DISPLAY: 1、“TIME/CAL” window: Display exercise time from 0:00-99:59 ,when count to 99:59, the machine will stop smoothly and show ‘ End ‘, then enter into initial situation after 5 seconds; When count down, it will show from the setting time to 99:00, when down to 0:00 , the machine will stop smoothly and show ‘ End ’, and will enter into the initial situation.Display exerciser calories worked out. It will count from 0.
CONSOLE BUTTON FUNCTION: “START” button: Start the power and attach the safety key to the treadmill, press this button to start the treadmill at 0.5MPH. 2、 “STOP” button:During the running, press this button the machine will reset the data and stop smoothly. 3、“SPEED+”、“SPEED-” button: Press the +/- button to increase or decrease the speed in increments of 0.1 MPH. Pressing and holding either of these buttons for a duration of over ½ a second will increase or decrease the speed continually.
PROGRAM EXERCISE CHART: RANGE OF PROGRAM: PROGRAM ORIGION TIME(MIN:SECOND) SPEED(MPH) DISTANCE(MILE) STEP CALORIE(THERM) SET UP RANGE DISPLAY RANGE 0:00 0.0 30:00 5:00-99:00 0:00-99:59 0.5 0.5-4.0MPH(WALK) 0.5-8.0MPH(RUN) 0.5-4.0MPH(WALK) 0.5-8.0MPH(RUN) 0 3.00 1.00-99.0 0.00-99.9 0 N/A N/A 0-9999 0 50 20.0-990.0 0.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SUGGESTED ACTION Not plugged in Plug cord into outlet Safety Key not inserted Insert Safety Key Running belt tension not correct on the left or right sides of the running board Tighten the adjustment bolts on the left and right side of the rear roller Wires from the console and bottom control board not properly connected. Check wire connections from the console to the control board.
The motor wire is not connected or the motor is damaged. Check motor wires to see if the motor is connected. If the wire has been punctured or damaged, you will need to replace it. If the problem is not rectified, you may need to replace the motor. E08: Control Board Abnormality The control board is not connected. Check the upper and middle wires to see if the control board is connected. If the wire has been punctured or damaged, you will need to replace it.
EXERCISE INSTRUCTIONS 1.The Warm Up Phase This stage helps get the blood flowing around the body and the muscles working properly. It will also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as shown below. Each stretch should be held for approximately 30 seconds, do not force or jerk your muscles into a stretch - if it hurts, STOP. 2.The Exercise Phase This is the stage where you put the effort in.
MAINTENANCE & CARE General cleaning will help prolong the life and performance of your treadmill. Keep the unit clean and maintained by dusting the components on a regular basis. Clean both sides of the running belt to prevent dust from accumulating underneath the belt. Keep your running shoes clean so that dirt from your shoes does not wear out the running board and belt. Clean the surface of the running belt with a clean damp cloth.
IMPORTANT NOTE: You will need to lubricate your treadmill before the first use. RUNNING BELTS & TREADMILL LUBRICANT: Lubricating the running board and running belt is essential as the friction between the two affects the life span and function of the treadmill, therefore it is suggested that the running board and belt be inspected regularly. WARNING: Always unplug the treadmill from the electrical outlet before cleaning, lubricating or repairing the unit. HOW TO LUBRICATE: 1.
EXPLODED DRAWING 19
PARTS LIST: Q’ty No.
No. Description Specification Q’ty Specification Q’ty No. Description E12 Magnetic Ring 1 E03 Keyboard plate 1 E04 Signal top wire 1 E13 Magnetic Core 1 E05 Keyboard plate top wire 1 E14 AC single wire 2 E06 Keyboard plate middle wire 2 E15 AC single wire 2 E08 DC motor 1 E16 Grounding Wire 1 E09 Remote control 1 E17 Power socket 1 E10 Running Deck 1 E18 Power line 1 E11 Square Switch 1 Q’ty No. Description 1 G01 Bluetooth model Optional parts: No.
ZWIFT APP 22
WARRANTY MANUFACTURER'S LIMITED WARRANTY The supplier warrants to the original purchaser that this product is free from any defect in materials and/or workmanship, provided that the product is properly installed, properly operated and used for the intended purpose (for home use ONLY). This limited warranty is extended ONLY to the original purchaser, and only covers products purchased as new.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
