Instruction Manual for C01 To bring you a better experience, please read these Instructions carefully. A. Bind Your Device a. Download and Install the App Download the InxFIT App by scanning the QR code or searching in the App Store. Note: the operating system of your mobile phone needs to meet the following requirements: iOS 10.0 1. or Android 6.0 Bluetooth 4.2 Scan the QR code below to download the InxFIT App. (The QR code may be updated.) 2.
b. Binding Steps (Note: during the binding process, InxFIT will ask you to turn on the Bluetooth of your mobile phone and authorize InxFIT to access the GPS of your mobile phone. For IOS user, when a binding error occurs, please ignore this device in the Bluetooth list of your mobile phone first.) 1. On the Home page of the App, click “+” at the upper right corner and select [Add Device] to search for your watch. Find your watch in the Device List and click it to bind it. 2.
B. Data Synchronization The watch records various data on your activities when it is worn on your wrist. You can synchronize data with the App as follows: start the InxFIT App, and pull down the page to start a data synchronization. The synchronization progress is displayed on the page. Note: please perform a data synchronization at least every 7 days, or the data will be overwritten when the memory is full.
C. Instructions for Use a. Charging Diagram Follow the diagram below to connect and charge your watch. We recommend that you charge your watch before turning it on for the first time.
b. Wearing and Adjustment 1. Wear Your Watch Leave one-finger gap between the watch and your wrist bone, and adjust the strap to a comfortable length. 2. Replace the Strap Push the push button horizontally to loosen the strap, and then remove the strap. Push button Note: too loose or too tight wearing may affect the accuracy of HR or SpO2 measurement.
D. Operating Instructions a. Button Operations Press the button: return to the dial, or switch between the dial and function list. Press and hold the button: turn on/off the device. b. Change the Dial Press and hold the dial screen to display the dial selection list after vibration. Swipe horizontally to select the desired dial, and then click it to apply it.
c. Screen Operations Swipe the screen to enter different interfaces as shown below. E. Function Overview 1. Functions Sports / HR / SpO2 / Sleep / Alarm Clock / Breathing Exercise / Timer / Weather / Music Control / Stopwatch Note: the Weather function needs to be enabled on the App. More details on the functions can be found on the App.
2. Initiate an Exercise a. To start an exercise: click the “Sports” icon → select a sport → the exercise data recording will start at the end of the countdown. b. Control the exercise: press the side button to pause the exercise recording; press the side button again or click [Resume] on the screen to resume the exercise recording. c. Stop the exercise: press and hold the side button to stop the exercise, or click [Stop] on the screen to stop the paused exercise. F.
It is recommended to wear and clean the product as follows: 1. Keep the product clean. 2. Keep the product dry. 3. Don’t wear the product too tightly. Do not use detergents to clean the device. You can use soap-free detergents. For stains that are not easy to remove, it is recommended to clean with alcohol. I.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Manufacturer's Name: Shenzhen XiaoJu Intelligent Technology Co., Ltd. Address: 708, Block E, E-commerce Incubation Base, Taojindi, Longhua District, Shenzhen, China. C01 Smart Watch Model number: C01 Operating Temperature: -20°C to 45°C This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0mmmust be maintained between the user’s body and the watch, including the antenna.
DECLARATION OF CONFORMITY I hereby declare that the product Product name: C01 Smart Watch Model name: C01 Series model : N/A Trademark: N/A HW: C01_MB_V11_20211008 SW: V1.
NOTIFIED BODY: MiCOM Labs Inc Address: 575 Boulder Court, Pleasanton, California 94566 USA Identification Number: AB 2280 MANUFACTURER or AUTHORISED REPRESENTATIVE: Address: Shenzhen XiaoJu Intelligent Technology Co., Ltd. 708, Block E, E-commerce Incubation Base, Taojindi, Longhua District, Shenzhen, China. This declaration is issued under the sole responsibility of the manufacturer and, if applicable, his authorised representative. Point of contact: Name:Shan Jiang TEL.
