User's Manual

ManualsBrandsSHENZHEN WEIKING TECHNOLOGY ManualsAudio EquipmentBluetooth headset

Active Noise Cancelling Wireless Headphone

Package Includes

Speciﬁcations

Caution

Charging

Power On

Power Off

Music Control

Bluetooth connection

Overview of the Headphone

• 1 x ANC Headphone

• 1 x Micro-USB Cable

• 1 x AUX Cable (Ф3.5mm)

• 1 x User Manual

• Bluetooth Version: 5.0

• Support: A2DP V1 .2, AVRCP V1 .4, HFP V1 .6, HSP V1 .2

• Wireless working range: 10 meters

• Bluetooth transmitter frequency: 2.402-2.480GHz

• Bluetooth transmitter modulation: GFSK

• Driver Unit: Ф40mm (32ohm, 20mW)

• Frequency response: 20Hz-20kHz

• Audio-SNR@1 KHz = 93dB

• Mic-SNR@1 KHz = 92dB

• Active noise reduction: 20dB @ 20Hz-1 kHz (MAX)

• Battery type: Li polymer (3.7V/520mA)

• DC input voltage/current: 5V ± 0.25V I 0.5A

• Playtime: 19-22 hours (varies by volume level and

content)

• Battery charge time: 2-3 hours

• Dimensions: 202 x 150 x 71 mm

• Weight: 254g

• It is dangerous and illegal (in some jurisdictions) to

use headphones when you’re driving car, riding bike,

motorcycle, or watercraft.

• Do NOT use the headphone in situations where they

might cause distractions or prevent you from hearing

warning sounds.

• Keep the headphone away from ﬁre, water, liquids,

extreme heat: such like the dashboard of your car on a

hot day.

• Do NOT use this headphone at high volume for

extended periods, as this may cause permanent

hearing damage or loss.

• Do NOT drop or knock the headphone on hard surfaces.

• Do NOT use chemicals or detergents to clean the

headphone.

• Do NOT scrape the surface with sharp objects.

• Do NOT make unauthorized alterations to this

headphone.

1. Before ﬁrst time use, fully charge the built-in battery

2. Plug the small end of the USB cable into the USB

charging port on the left earcup. Plug the other end into

a USB wall charger or computer that is powered on.

Press the Play/Pause button until you hear a voice saying

“Power on” and the LED indicator light is ﬂashing blue (fast

the ﬁrst time, then slowly).

Press the Play/Pause button until you hear a voice saying

“Power off” and the LED indicator light ﬂashes red once. (If

you are playing music when switching the power off you

will hear a descending tone.)

Play / Pause Click

Volume Up Click

Volume Down Click

Next track Press and Hold

Previous track Press and Hold

1. Press the Play/Pause button and keep it pressed in

when the voice says “Power On”.

2. Keep pressing the Play/Pause button until you hea

r a

voice saying “Ready to pair” and the LED indicator light

is ﬂashing red and blue fast.

3. Go to the Bluetooth settings on your mobile device.

Search and select “Eartrons PRO” from the list.

4. Once your device is paired with the headphones, a

voice says “Connected” and the LED indicator slowly

ﬂashes blue.

Note: When the battery charge <3%, the headphone will

power off automatically.

Note: Under AUX-IN mode, headphone buttons and

speakerphone function are not workable.

Note: If the headphone battery is depleted, you cannot use

noise cancelling.

Note: When power is switched on (by pressing the Play/

Pause button until a voice says “Power on” and the LED in-

dicator starts ﬂashing blue), the headphones will automat-

ically reconnect to the last mobile device it was connected

to. (A maximum of 8 paired devices can be memorized.)

To save power, the headphones will automatically shut

down after 10 minutes in pairing mode if no devices are

paired.

Micro USB Charging Port

Microphone

Auxiliary Input Jack

Power/Pairing/ChargingLED Indicator

ANC On/Off Switch

ANC LED/Indicator

User Manual

LED Indicator

Blinking Red

Solid Red

Red light off

Battery Status

Need to charge ( charge<10% )

Under Charging

Full charged

Speakerphone (in Bluetooth Connection)

Answer an incoming call Click

Reject an incoming call Press and Hold

End the current call Click

Redial last-called number Press and Hold

Listening music from external audio source

Noise cancelling function

Troubleshooting

1. Power on the headphone.

2. Using the AUX Cable(Ф3.5mm), connect your external

device to AUX-in port on headphone.

3. It will automatically turn to AUX-in mode.

You can use the noise cancelling function with or without

power on. Slide the “ANC” button to turn on/off the noise

cancelling function.

Cannot power on: Charge the headphone and make sure it

has enough battery charge.

Poor sound quality: Move the device closer to this head-

phone or remove any obstacle between them.

Cannot connect wi

th the device: Please check:

• The Bluetooth device supports A2DP proﬁle

• The headphone is within 1 Om from the device.

• The headphone is in pairing mode, the LED indicator

blinking blue and red.

No Sound: Make sure the music volume is at audible level

on both your device and headphone.

Make sure your device is successfully paired with the

headphone, the LED indicator turn solid blue.

Volume up/Next track

BT On/Off, Play/Pause

Volume down/Previous track

Summary of content (2 pages)

PAGE 1
Package Includes Charging Bluetooth connection • • • • 1. Before first time use, fully charge the built-in battery 2. Plug the small end of the USB cable into the USB charging port on the left earcup. Plug the other end into a USB wall charger or computer that is powered on. 1. Press the Play/Pause button and keep it pressed in when the voice says “Power On”. 1 x ANC Headphone 1 x Micro-USB Cable 1 x AUX Cable (Ф3.
PAGE 2
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.