Remote Dog Training Collar Operation Guide
Dog Training Collar Operation Guide Thank you for choosing PTS1200 Remote dog training collar. Our mission is to offer the best electronic training solutions. We want to ensure your dog’s safety by providing you with the tools and techniques to successfully train your pet. Please feel free to contact us if you have any problems and we will resolve them immediately. Please read the complete operation guide carefully before starting to train your dog including the FAQ.
Proper fit of the collar under the dog’s neck is important. A collar worn for too long or made too tight on your dog’s neck may cause skin damage or irritation. This can range from redness to pressure ulcers; commonly known as bed sores. Training collars can cause pressure necrosis if used incorrectly and is often misidentified as burns. 1. Avoid leaving the collar on the dog for more than 8 hours out of every 24 hours and try to reposition the collar on your dog’s neck every 1 to 2 hours if possible. 2.
7. If a rash or sore is found, discontinue use of the collar until the skin has healed. 8. If the condition persists beyond 48 hours, see your veterinarian. These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear stainless steel contacts. Some pets are sensitive to contact pressure and it is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed.
Table of Contents Components…………………………………………...6 How the system works…………………………...........6 Main Features………………………………………….7 Transmitter…………………………………………….9 Receiver Collar……………………………………….12 Setting Up Multi-dog System………………………...15 Charging……………………………………………....19 Anti Bark Operation…………………………………..21 High Light flashing LED……………………….……..24 Training Guide………………………………………..
Battery Replacement……………………….………….26 General Training Tips.………………………………....27 Intensity Selection Tips………………………………..29 Test Light Instructions…………………………………29 How Dogs Learn……………………………………….30 Frequently Asked Questions…………………………...
Components How the System Works The PTS1200 dog trainer has been proven safe, comfortable, and effective for all pets over 10 pounds and 6 months old. This system assists you in controlling your pet without a leash in a long distance range. At the push of a button, the remote transmitter sends a signal, activating the receiver collar.
and correctly, many misbehaviors that your pet exhibits can be corrected or any basic obedience commands can be taught. Also, The PTS1200 dog trainer has anti bark function .When you press the on/off button of receive collar to turn on the anti bark function. The microphone will be activated by dog’s bark then the receive collar will emit warning beep and static shock to stop barking. Important: The remote trainer actual distance is dependent on the way you hold the remote transmitter, the range may vary.
- Highlight LED function allows you to find pet from 200~300 meters away at night - 10 levels each of static shock. - 10 levels of vibration - “Beep” sound activated with a separate button. - Two buttons “+” and “-” allow you to set your intensity - LCD digital display for 10 shock & vibration levels & dog ID - Memorize shock level in transmitter for different dogs. - Easy to operate with rubber button. - Waterproof transmitter and receiver. Dogs can swim freely. - Rechargeable 3.
Transmitter LCD display Antenna LED Light Stimulation Level Bell Button Button Vibration Button On/Off Static Button Shock Button Dog Selection Button DC Jack Cover -9-
“ ” and “ “buttons: Press these buttons to adjust the shock and vibration intensity from levels 1 to 10. “ ”button: This is the power switch; hold this button for 2seconds to switch on power, then LCD will display the default “A01”. You may change Dog ID by pressing the relative buttons. If you want to switch off the power, hold this button for 2 seconds to switch off power. “ ”button: No-stimulation warning beep “ ”button: Vibration stimulation. Press 1 time- vibrate 1 time.
the button. Will stop automatically once you get past 8 seconds of holding the button. “1, 2, 3”buttons: Dog selection button, default is “1”. Your transmitter is capable of training up to three dogs with optional receiver collars. You select” 1 “dog, LCD display dog ID “A XX”. If you want to train 2 dog, press “2” button, LCD will display “BXX”. If you want to train 3 dog, press “3” button again, LCD will display “C XX”. “XX” is for showing the shock& vibration level from 1-10.
Receive Collar NOTE: CHARGE RECEIVER BEFORE FIRST USE. IF IT DOESN’T CHARGE CONTACT US IMMEDIATELY Contact Prong Choose short or long prong to match the dog’s coat type. Microphone Dog bark sensor, Pick up the dog’s bark LED Light Indicate the working status, low battery ,charging status. DC Jack Cover Open the Rubber Cover and insert the adaptor plug into DC Jack to charge.
Spanner Change the Contact Prong depending on the pet’s coat type. Note: If the contact prong is tight, don’t continue to turn the spanner clockwise or the contact prong will be broken. Never turn the contact prong too tightly. Turn anticlockwise to loosen or remove. You can expand your one dog trainer to a multi-dog remote trainer by yourself. Simply purchase extra receiver collars and add them to your system. NOTE: IF THE COLLAR DOESN’T TURN ON PLEASE CONTACT US FOR A NEW BATTERY OR CHARGER.
Key Points to note 1.Always charge before use. Ideal time to charge is 2-3 hours for the receiver as this is better for the life of the battery. 2.The on/off buttons need to be held down for several seconds to turn the units on and off 3.When the green LED light flash 1 time of 5 seconds. The remote function is on , the anti bark function is off . When the green LED light flash 2 times of 5 seconds, the remote function is off, the anti bark function is on . 4.
6.If the green light goes from flickering fast, to flickering once every 4-5 seconds, it is now connected, you just need to take it out of connection mode. 7.The receiver is still waterproof without the rubber stopper in place. This does not affect performance. If the receiver is submarine for more than 2 hours , please take it out and clean the water of Microphone hole. 8.You may remove the receiver and attach it to a collar that you prefer to use instead that fits. Setting Up Multi-Dog System 1.
disconnected from the remote. (Note: Never open 2 or more unmatched receivers at the same time.) Step 2: Take out the transmitter that you want to match to the receiver. Press and hold on the “ ” button until LCD display occurs then release, the transmitter is now on. Step 3: Press and hold the Dog selection button and “ ” button at the same. Not to release the two buttons.
If you want to match the 2nd dog , press and hold on “2” button and “ ” button at same time until the digital numbers on the LCD display starts counting up on the screen. If you want to match the 3rd button and “ dog , press and hold on “3” ” button at same time until the digital numbers on the LCD display starts counting up on the screen. Step 4: Hold the transmitter close to the unmatched receiver 1 to 2 inches away.
matched the receiver. You can also use the test light to place the prongs in the little gaps and press each button on the remote to see if the test light comes on. This shows that the collar is working. If you choose, you can also put it on the lowest setting and test on the back of your hand/arm for confirmation if you’re still unsure. If the collar didn’t connect, please repeat the step3 to step 4. Try to close to the collar from different direction and more close.
is on. Step 3: Press and hold the “ ” button and “ ” button at the same time, until the digital number on the LCD display counts up continuously (01,02,03…98,99). increasing automatically, this is correct. Not to release the two buttons. Step 4: Hold the transmitter next to the receive collar 1 to 2 inches away. You can listen for the 5 “beep” sounds from the receiver. The green LED light of the receiver should now be flashing frequently.
Common adapter for transmitter and receiver charging. To recharge, open the rubber cover first. Plug the adapter contact pin into the AC power outlet and insert the adapter plug into the receiver DC Jack. The transmitter and receiver collar can be charged by connecting USB cable and other 5V DC power supply, such as cell phone adapter, notebook, or computer. Do not charge batteries in hot areas, keep far away from fire. NOTE: IF THE COLLAR DOESN’T TURN ON PLEASE CONTACT US FOR A NEW BATTERY OR CHARGER. 1.
The LCD display is “CHA” when charging. The LCD display is “FUL” when the transmitter is full charged . The transmitter’s red LED light will flash when the battery is low Stimulation Your remote trainer has 10 levels of intensity, so you can find the best level for your dog’s temperament and the type of training. You may also select either vibration or shock stimulation, depending on your dog’s temperament and your training purpose.
Your remote trainer has anti bark function. Please follow the below steps to turn on the Anti bark mode. Step 1: Choose proper shock level for anti bark 1) Press the “ ” or “ “buttons to select suitable shock level. 2) Then press “ ” button and confirm the receive collar receive the signal from Transmitter and emit at least one shock . The receive collar will keep this shock level for anti bark when you turn on the anti bark mode at once. 3) If you want to change the anti bark shock level .
of 5 seconds . The anti bark mode is on ,the remote control function is off .The Transmitter can not control the receiver under anti bark mode Step 3: Turn the anti bark mode off Hold and press on the On/Off button of receive collar again for more than 2 seconds. When the red light is on then release it at once. The green Led light of receiver will flash 1 times of 5 seconds . The anti bark mode is off ,the remote control function is on .
High Light flashing LED Your remote trainer has 3 colors(white, red and green) of high light flash. You can find out your pets from 200-300 meter away in dark night without remote control. To get highlight flash in dark night , you must match the receive collar to transmitter first . 1)Continuous flash : Press and hold on“1” button of Transmitter for 3 seconds , the 1st dog receive collar will highlight flash 5 times then flash 1 time per 3 seconds continuously.
The 1st dog receive collar is White highlight Led, The 2nd dog receive collar is Red highlight Led , The 3rd dog receive collar is Green highlight Led , TRAINING GUIDE Choosing the Appropriate Length of Contact Points This is a critical step and is often overlooked. If you don’t have the proper length contact points, the collar won’t work correctly. For smaller dogs, the short contact points should be used. For larger dogs, or dogs with a heavier hair coat, you should use the longer contact points.
Tighten the buckle by holding it with two fingers as you pull the strap snug. Remote training collars must be put on a dog quite snuggly to ensure consistent contact and reliable stimulation. The collar needs to be placed relatively high on the dog’s neck, usually just a couple of inches below the dog’s ears. The collar should be pretty snug on the dog’s neck and it should not dangle. If the collar is too loose, the contact points will not be touching your dog and it will not work.
Any problems with charging or battery life, including not charging or turning on, please contact us. The batteries contained are designed and produced specifically for this device. If you need a new battery please contact us or visit our website and we should have some available. When removing the old battery pack, care must be taken when gripping the connector firmly to avoid damaging the wires. Never shorten the battery wires as though unlikely, it may cause fire or explosion. General Training Tips 1.
misbehaviour. 6. Teach the dog a command first before reinforcing the command with the remote transmitter. 7. Issue one obedience command at a time. Do not use the training system for commands that the dog has not learnt. 8. Do not overcorrect your dog. Use as few stimulations as possible to train your dog. 9. During training, look for all the positive changes in the dog's behavior and remember to reinforce them promptly with ample praise and reward. 10.
13. Never use the PTS1200 Dog Training Collar to correct or eliminate any form of aggressive behaviour. If your dog exhibits such behaviour, contact a professional trainer. Aggression in dogs is the result of many factors- it may be a learned behaviour or it may be brought on as a result of fear. Another factor contributing to aggression in dogs is social dominance. Every dog is different.
3. Press a stimulation button on the remote transmitter. 4. The test light will flash. 5. Turn the collar receiver off. Save the Test Light for future testing. Note: If the Test Light does not flash, recharge the battery and re-test. . HOW DOGS LEARN Here are some basic guidelines that cover all your remote trainer work on obedience commands. Follow a step-by-step introduction process on each command. Don’t assume that your dog will understand a remote trainer correction in connection with a command.
Don’t introduce remote training around distractions. Keep things simple for your dog in their first sessions. They can’t learn well when there’s too much going on. Learning to Train Every animal on the planet has an alpha or beta relationship with every other animal. We usually think of “beta” as submissive and beaten down, but in wild packs or herds, that is not the case. The beta dog in a pack of wild dogs is still quite happy and lives a good life.
challenges are subtle. Those are the ones you must pay close attention to while training. If you win the small battles, the big fights will be much easier to handle. Dogs see the world in black and white. To your dog, either you are in control or it is. There is no middle ground. There are two most important points, conditioned responses and substitution, will be the cornerstones of your training program. Conditioned responses to commands are mandatory for a properly trained dog.
1,000 repetitions per command will do this nicely. That might seem like an undoable task but if you will train consistently, it will take only a short time. Substitution: This is where we use a stimulus to cause a response and then add another stimulus simultaneously until the second stimulus evokes the same response as the first. You might remember Dr. Pavlov’s work with ringing the dinner bell as he was feeding his dog.
to achieve desired results. Is the collar waterproof? Yes, they are designed to be completely waterproof. Any problems please email us for a faster or similar response time. If the rubber stopper comes away from the charging port, is the collar and remote still waterproof? Yes, this makes no difference to the waterproof status of the device, though keep in place if possible to keep debris out and for peace of mind.
Once my dog is trained, do I still need to use the collar? This is up to you, you can keep the collar on for insurance, or only wear it in high risk environments. If you dog is completely trustworthy now you can choose either way. You may also just use it from time to time as a reinforcement or as a refresher for certain behaviors. Can I use this on my aggressive dog? We do not recommend any of our products to be used on aggressive dogs.
You can hold down the vibration or shock button for up to 8 seconds before the safety feature kicks in and it stops. You then need to press the button again if you want to shock for up to 8 seconds again. What do I do if on the off chance my dogs neck becomes red and irritated? This is due to the contact points irritating the skin. Discontinue use for a few days. If the condition persists beyond 48 hours, see your veterinarian.
shock to see if the button lights up. If they do then the collar is ready to go. Can I test the collar on the back of my hand or arm? This is up to you and we take no liability for this action. Some people choose to do this so they can feel the intensity that the dog is experiencing. The lower levels might not be felt by you depending on your sensitivity. Is this a continuous or one-time shock? Both. It will stop when you let go of the button. If you only press it once then is will be a one-time shock.
How long does the battery last? The length of time the battery lasts between charges depends on how much you use the device. If used often is will need to be charged every other day like a mobile phone. The batteries are designed to last 3-5 years if used regularly. Any problems please contact us and we can send a replacement. Troubleshooting Guide Problem#1: No stimulation when a transmitter button is pressed. The receiver has not been activated.
Problem#3: The stimulation seems too high, not high enough or no feeling at all The collar strap is not tight enough. Make sure the contacts points connect to the dog’s skin well. The intensity level is not correct. Change the level. The batteries are dead. Recharge as needed. Problem#4: The receiver light changes color to indicate low battery very quickly The unit has been left turned on in between training session. Make sure the receiver is turned off after use. You are training in very cold weather.
so that the light faces toward the dog’s nose. Radio interference. Wait a short while then try again, or move to another area. Problem#6: The receiver can’t receive any signal or cannot work at all Check the receiver on/off button, make sure the receiver is turned on. Check the receive collar green Led , make sure it flash 1 time of 5 seconds. Check the transmitter, if it has a low battery, charge transmitter first. The battery is broken, please contact us and we will send you a replacement battery.
- 41 -
FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
