User's Manual

ManualsBrandsShenzhen Sunricher Technology ManualsElectronicsRF sender

Table Of Contents

RF RGBW Controller

SR-2819T8 with SR-1009FA series

Parameter

Wiring diagram

Product Size

Part No.

Input Voltage

Remarks

Output Current

SR-1009FA 12-36VDC

Constant voltage

4x(60-180)W

4x5A

Output Power

SR-1009EA 12-36VDC

Constant voltage

4x(96-288)W4x8A

Remote

Part No.

Operation Voltage

DIMENSIONS

ø/h (mm)

Operation

Frequency

SR-2819T8 4.5VDC

43.8x131.6x24.5

916.07MHz

Receiver

SR-1009FA3 12-36VDC

Constant current

4x(4.2-12.6)W

4x350mA

SR-1009FA7 12-36VDC

Constant current

4x(8.4-25.2)W4x700mA

43.8

131.6

24.5

Brief introduction of buttons

R G

Short press: switch on/off each channel;

Long press: dim up/down each channel

B W

Working status indicator, the sender is in dormant status when the indicator is off. The

sender is under working when the indicator is flashing rapidly. If the indicator continues

flashing at the frequency of 1 second, it indicates that the sender batteries low and

needs to replace new batteries.

S-

Speed down when color is changing

S+

Speed up when color is changing

B-

Brightness down

B+

Brightness up

Turn ON/OFF

Touch wheel for selecting R/G/B colors

R G B W

S- S+

W+

B- B+

P- P+

6 7

P- P+

1 2

Build-in 10 Dynamic modes,P- is previous mode,P+ is next mode.

are zone numbers,long press switch on/off each zone.Short press is to choose a

zone.To synchronize several zones,short press 2 or more buttons one after another.

1)Receiver Connection Diagram for Single Unit

2) Connection Diagram for Multiple UnitsReceiver

Power Supply

12-36VDC

110V-230VAC

white

SR-1009FA

LED CONTROLLER

1234

Learning Key

white

SR-1009FA

LED CONTROLLER

1234

Learning Key

white

SR-1009FA

LED CONTROLLER

1234

Learning Key

Power Supply

12-36VDC

110V-230VAC

white

SR-1009FA

LED CONTROLLER

1234

Learning Key

Press-button RGBW controller

Receivers work with WIFI-RF convertor to be controlled by smart phone

2 3

8 zones,long press can turn on/off each zone

5 6

Note: If you press R, then press G, then it is mix color of R and G. If you want

to get G color directly, please press R to switch off of R first. Then press G.

Summary of content (3 pages)

PAGE 1
RF RGBW Controller Brief introduction of buttons SR-2819T8 with SR-1009FA series Working status indicator, the sender is in dormant status when the indicator is off. The sender is under working when the indicator is flashing rapidly. If the indicator continues flashing at the frequency of 1 second, it indicates that the sender batteries low and needs to replace new batteries.
PAGE 2
Operation 1. Do wiring according to connection diagram and install battery into remote control. 2. How to learn&delete ID process? a. Turn on the remote by . b. Short press at Learning Key on receiver. c. Press any zone button(which you desire to control) on remote, for example 1 . d.Then touch color wheel. e.Connected LED light will blink to confirm zone designation.
PAGE 3
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.