User's Manual

ManualsBrandsShenzhen Sunricher Technology ManualsElectronicsRF sender

Table Of Contents

RF wireless LED remote controller

6 zones/areas

Press-button Dimmer

Model:SR-2819DIM with SR-1009Fxx

Parameter

Wiring diagram

Product Size

Brief introduction of buttons

Receivers work with WIFI-RF converter to be controlled by smart phone

Part No.

Input Voltage

Remarks

Output Current

SR-1009FA 12-36VDC

Constant voltage

4x(60-180)W

4x5A

Output Power

SR-1009EA 12-36VDC

Constant voltage

4x(96-288)W4x8A

Remote

Part No.

Operation Voltage

DIMENSIONS

ø/h (mm)

Operation

Frequency

SR-2819DIM 4.5VDC

48x140x17

916.665MHz

Receiver

SR-1009FA3 12-36VDC

Constant current

4x(4.2-12.6)W

4x350mA

SR-1009FA7 12-36VDC

Constant current

4x(8.4-25.2)W4x700mA

Remarks

load 3pcs 7 AAA (1.5V)

batteries

1)Receiver Connection Diagram for Single Unit

2) Connection Diagram for Multiple UnitsReceiver

Power Supply

12-36VDC

110V-230VAC

whit e

SR-1009FA

LED CO NTROLLE R

1234

Lear ning Ke y

whit e

SR-1009FA

LED CO NTROLLE R

1234

Lear ning Ke y

whit e

SR-1009FA

LED CO NTROLLE R

1234

Lear ning Ke y

Power Supply

12-36VDC

110V-230VAC

whit e

SR-1009FA

LED CO NTROLLE R

1234

Lear ning Ke y

Sing le c ol or

LED Stri p

4x5A

Power Supply

12-36VDC

110V-230VAC

whit e

SR-1009FA

LED CO NTROLLE R

1234

Lear ning Ke y

2x10A

Note:

One receiver can work with 1-8pcs SR-2819DIM

One SR-2819DIM control multiple receivers

The power supply chosen must be 20% higher than the actual load

Sing le c ol or

LED Stri p

Sing le c ol or

LED Stri p

Sing le c ol or

LED Stri p

Sing le c ol or

LED Stri p

Sing le c ol or

LED Stri p

Sing le c ol or L ED Strip

140.0

48.0

17.0

Indicator: indicate the state of

remote control

Brightness button

Brightness wheel

ON/OFF of all zones

50% Brightness

100% Brightness

25% Brightness

75% Brightness

6 zones: each zone can save

3 color or modes

Save button

Summary of content (3 pages)

PAGE 1
RF wireless LED remote controller Brief introduction of buttons Model:SR-2819DIM with SR-1009Fxx Indicator: indicate the state of remote control Brightness button Brightness wheel 25% Brightness ON/OFF of all zones 50% Brightness 100% Brightness 75% Brightness 6 zones/areas Press-button Dimmer Receivers work with WIFI-RF converter to be controlled by smart phone S1 S2 S3 S4 S5 S6 1 2 3 4 5 6 6 zones: each zone can save 3 color or modes Save button Wiring diagram 5 1)Receiver Connection
PAGE 2
Operation Warranty Agreement Learning (matching) a. Do wiring according to connection diagram b. Wake up the remote control by touching ON/OFF button. c. Press learning button on receiver. d. Touch any zone button on remote control. e. Then touch brightness wheel. f. Connected LED light will blink to confirm zone designation. g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
PAGE 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.