User's Manual

ManualsBrandsShenzhen Sonoff Technologies ManualsComputers & AccessoriesSONOFF New Zigbee Bridge

Table Of Contents

User manual V1.0

· 中文 -----------1-5 · English----------6-10 · FCC Warning--------11

New Zigbee Bridge

ZB Bridge-P

Summary of content (13 pages)

PAGE 1
ZB Bridge-P User manual V1.
PAGE 2
中⽂ Shenzhen Sonoﬀ Technologies Co., Ltd. 产品介绍 Zigbee信号指⽰灯(绿⾊) Wi-Fi信号指⽰灯(蓝⾊) 输⼊接⼝配对按钮设备重量＜1Kg，建议安装⾼度＜2⽶。信号指⽰灯状态说明状态状态说明蓝灯两短⼀⻓闪烁 Zigbee配⽹模式蓝灯快闪兼容模式(AP) 蓝灯常亮设备在线蓝灯快闪⼀下未连接路由蓝灯快闪⼆下已连接上路由器，但未连接到云端蓝灯快闪三下固件升级中绿灯慢闪搜索添加⼦设备中产品特点本设备是⼀款Zigbee多功能⽹关，⽹关通过Wi-Fi转Zigbee的⽅式进⾏连接控制多种Zigbee 设备，实现远程控制该设备的开和关、设置智能定时和分享给您的家⼈⼀起控制等等。使⽤说明 1.
PAGE 3
中⽂ Shenzhen Sonoﬀ Technologies Co., Ltd. 2. 上电使⽤ Micro USB 线给设备通电。通电后，设备⾸次使⽤，默认进⼊Zigbee配⽹模式, Wi-Fi指⽰灯呈“两短⼀⻓闪烁”。三分钟内没有进⾏配⽹，设备将退出Zigbee配⽹模式。如需再次进⼊，⻓按配对按钮5秒直到 Wi-Fi指⽰灯呈两短⼀⻓闪烁即可。 3.
PAGE 4
中⽂ Shenzhen Sonoﬀ Technologies Co., Ltd. 4. 在 Zigbee ⽹关中添加 Zigbee ⼦设备 ZB Bridge 添加设备正在连接请让设备尽量靠近网关已添加设备:0 暂无子设备，请添加 135s 添加正在搜索设备 2个设备已找到下一步先把⼦设备设置进⼊配对状态，再点击⽹关界⾯中的”添加” ，等待搜索完成添加⼦设备。通过中继功能，单个⽹关⽬前最多可添加128个⼦设备。兼容模式(AP) 如使⽤Zigbee配对模式配⽹失败，请使⽤“兼容模式(AP)”进⾏配对。 1 2 ⻓按配对按钮5秒直到Wi-Fi指⽰灯呈“两短⼀⻓闪烁”状态，松开。再次⻓按配对按钮5秒直到Wi-Fi指⽰灯呈“快闪”状态，此时设备进⼊兼容模式。在app界⾯，点击“+”，选择“兼容模式”。先把移动设备连接上Wi-Fi账号为：ITEAD-******，密码为：12345678，然后回到“易微联”app，点击 “下⼀步” ，等待配对完成。产品参数型号 ZB Bridge-P 输⼊ 5V ⽆线连接 Wi-Fi IEEE 802.
PAGE 5
中⽂ Shenzhen Sonoﬀ Technologies Co., Ltd. 取消报警声通过场景联动触发⽹关声⾳报警，可通过以下任意⽅法静⾳： 1. ⽤卡针短按⽹关配对按钮。 2. 在eWelink App⽹关⻚⾯点击红⾊喇叭图标。 3.
PAGE 6
Shenzhen Sonoﬀ Technologies Co., Ltd. 中⽂恢复出⼚设置在 eWeLink App 端“删除设备”，设备即恢复出⼚设置。常⻅问题 Wi-Fi设备与 eWeLink APP 配对失败。 1. 确保设备处于配对模式。三分钟内没进⾏配⽹，设备将⾃动退出配对模式。 2. 请开启定位服务并允许定位权限。在选择 Wi-Fi 络之前，请开启定位服务并允许定位权限。位置信息权限⽤于获取 Wi-Fi 列。果单击禁⽤，您将⽆法添加设备。 3. 确保您的 Wi-Fi 络为 2.4GHz 频段。 4. 确保您输⼊了正确的 Wi-Fi SSID 和码，没有包含特殊字符。密码错误是配对失败的⼀个⾮常常⻅的原因。 5. 配对时设备应靠近路由器，以保证良好的传输信号条件。 Wi-Fi 设备“离线”问题，请通过 Wi-Fi LED 指⽰灯状态检查以下问题： LED 指⽰灯每 2 闪烁⼀次，表⽰您⽆法连接到路由器。 1. 可您输⼊了错误的 Wi-Fi SSID 和码。 2.
PAGE 7
English Shenzhen Sonoﬀ Technologies Co., Ltd. Product Introduction Zigbee LED indicator(Green) Wi-Fi LED indicator(Blue) Input Pairing button The device weight is less than 1 kg. The installation height of less than 2 m is recommended.
PAGE 8
English Shenzhen Sonoﬀ Technologies Co., Ltd. 2. Power on Power the device through Micro USB cable. After powering on, the device will enter the Zigbee Pairing Mode during the ﬁrst use. The Wi-Fi LED indicator changes in a cycle of two short and one long ﬂash and release. The device will exit the Zigbee Pairing Mode if not paired within 3mins.
PAGE 9
English Shenzhen Sonoﬀ Technologies Co., Ltd. 4. Add Zigbee sub-devices to Zigbee Bridge ZB Bridge Add Device Connecting Added:0 Keep the device close enough to the hub. No sub-devices yet. 135s Add Looking for devices 2 devices Found Next Make the sub-devices enter the pairing mode, tap “Add” icon on the Zigbee Bridge interface, then wait it to ﬁnd the sub-devices and pair. Through connecting the routers, single Zigbee Bridge can add up to 128 sub-devices.
PAGE 10
English Shenzhen Sonoﬀ Technologies Co., Ltd. Cancel the alarm sounds The gateway alarm sounds that triggered by setting scene control can be muted in any following ways: 1. Press the gateway pairing button with a SIM Pick. 2. Click the red “speaker” icon on the gateway interface of eWeLink App. 3. Mute the gateway through scene control settings.
PAGE 11
Shenzhen Sonoﬀ Technologies Co., Ltd. English Common Problems Fail to pair Wi-Fi devices to eWeLink APP 1. Make sure the device is in pairing mode. After three minutes of unsuccessful pairing, the device will automatically exit pairing mode. 2. Please turn on location services and allow location permission. Before choosing the Wi-Fi network, location services should be turned on and location permission should be allowed. Location information permission is used to obtain Wi-Fi list information.
PAGE 12
Shenzhen Sonoﬀ Technologies Co., Ltd. FCC Warning FCC Warning Changes or modiﬁcations not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 13
Hereby, Shenzhen Sonoﬀ Technologies Co., Ltd. declares that the radio equipment type ZB Bridge-P is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals The FCC IDs of ZigBee sub devices supported by the current device are as follows： SNZB-01P FCC ID：2APN5SNZB-01P SNZB-02P FCC ID：2APN5SNZB-02P SNZB-03P FCC ID：2APN5SNZB-03P SNZB-04P FCC ID：2APN5SNZB-04P Shenzhen Sonoﬀ Technologies Co., Ltd.