CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Version: V1.00.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Trademark Information General Notice is a registered trademark of SHENZHEN SMARTSAFE TECH. CO., LTD. (SMARTSAFE for short) in China and other countries. All other SMARTSAFE trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of or are otherwise the property of SMARTSAFE or its affiliates.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual specified in the manual of the auto to be operated. Otherwise, SMARTSAFE shall not be liable for any direct or consequential damages. The equipment is for specialist or qualified technician use only. Disclaimer Note: specifying operations that require attention when operating the equipment.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Table of Contents Introduction......................................................................................................................................................................2 Features..........................................................................................................................................................................2 Working Conditions..............................................
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual transmission. It prolongs the work life of transmission. Introduction Working Conditions The transmission fluid inside transmission will go bad after a period of usage of automatic transmission. If the transmission fluid cannot be changed completely in time, it may cause the abnormality to the transmission.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 2. Overall structure Fig.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 3. Pipeline diagram The pipeline diagram is as shown in Fig.3. Fig.3 1-Pump; 2,3,15,23-Three-way solenoid valves; 4-Fluid filling port; 5-New fluid tank; 6,8-Electronic scales; 7-Detergent container; 9- Used fluid tank; 10,17-Filters; 11- Fluid path identifier; 12,18- Pressure gauges 13,14- Sight indicators; 16-Two-way solenoid valve; 19- Check valve; 20- Ball valve for fluid draining; 21- Temperature sensor; 22- Old oil sampling valve.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 5. Control panel The control panel is as shown in Fig.5. Fig.5 Description: Element NEW USED Description Observe the flow rate and compare the color of new and used fluid. Display the fluid outlet pressure. Display the fluid pressure of AT radiator. Press it to select function option in main menu. Press it to select function option in main menu. OK DEL Confirmation. 1. Menu to return. 2.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Fig.6 2. The main menu of display screen is as shown in Fig.7. Fig.7 Item Description Old oil sampling Sampling the oil from AT Add detergent Add ATF detergent to AT Exchange Exchanging ATF Adjust fluid level Adjusting the quantity of fluid inside AT Empty new tank Empty used tank Draining left fluid inside new fluid tank Draining used fluid inside used fluid tank Modifying the system parameter, e.g.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 1.3 Power cables connection Connect the power cables of the main unit to the designed power supply. 1.4 Check-up 1) Start the engine, and ensure that there is no leakage in pipeline. 2) Confirm that the power supply of the CAT-601S is normal, and then switch on the unit. Fig.8 2.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 3. Filling liquid 3.1 Filling detergent When you are ready to perform the circulating cleaning for auto transmission, please fill proper amount of detergent into the detergent container (please refer to Fig.3). 3.2 Adding new oil When you are ready to perform the ATF exchange operation, please fill new fluid into the new fluid tank from the fluid filling port (please refer to Fig.3). Fig.12 4) 4.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 1） Start the vehicle to warm up the fluid inside the transmission to normal temperature and fill the new transmission fluid with desired amount into it. 2） Check if the pipelines are well connected. 3） ATF exchange: as shown in Fig.14, you can directly input the fluid amount to be changed, as well as you can obtain the amount by selecting Vehicle Selection option. Fig.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Fig.21 Fig.25 After ATF Change finished, the screen will display the amount of the new fluid changed, the amount of the used fluid changed, and the error between them, while printing out the amount of the new fluid which has been changed. Press RETURN key to return to the previous menu. 1) 2) Fig.22 3) Check the fluid level inside transmission. If the level is not enough, supplying fluid is required.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 7. Empty new fluid tank 1) Be sure that the two hoses marked with “TO TRANSMISSION” are not connected with the vehicle to be maintained. 2) Open the handle valve on the fluid hose marked with “EMPTY”, and then place the hose into container. 3) The system will OK into the interface for Empty new tank, and automatically start fluid draining operation, as shown in Fig.29. Fig.26 2) Input the amount to be filled, press OK key.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual 4) Remove the new fluid tank. When the value displayed on the interface is stable, please press OK key to save the data. The interface is as shown in Fig.34. Fig.30(b) 9.1 Sensor calibration 1) Select the item for sensor calibration, press OK key to OK the sensor calibration menu as shown in Fig.31. Fig.34 5) Put the weight on the plate. When the value displayed on the interface is stable, please press OK key to continue.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Menu of [Sensor Calibration], and then press OK key to OK, the interface is as shown in Fig.37. Fig.40 Fig.37 13) According to the prompts on the interface, OK the amount (such as 0.3L) of detergent to be added into the system, and then press OK key to start adding. The interface is as shown in Fig.41. 9) According to the prompts on the interface, OK the current temperature value (Unit: ℃), and then press OK key to save the data.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Fig.46 According to the prompts on the interface, OK the date (4 bits for year, 2 bits for month and other 2 bits for date), and then press OK key to confirm. The interface prompts “OK”. b) Set Time On the menu of [Date & Time], please select [Set Time] option, and then press OK to confirm, the interface is as shown in Fig.47. Fig.43 9.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Press OK key to OK the menu of BMW. The interface is as shown in Fig.53. Fig.49(b) 9.7 Vehicle Adding Fig.53 Select [Vehicle Adding] setting option on the Main Menu of [System Setting], and then press OK key to OK the interface as shown in Fig.50. Select [BOTTOM NODE] option can add the last layer menu, and then press OK key to confirm. The interface is as shown in Fig.54. Fig.50 Fig.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual history records, and mean while delete the prompts for abnormal fluid filters(i.e. the filter status icon on the interface will automatically turn green from orange), as shown in Fig.59. Fig.56 Print information can choose print output content. The information contained in the options that are not selected cannotbe printed out, as shown in Fig.57. Fig.59 9.10 Device information Select the device information option and press OK key.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Main adapters No. ERP Code A01 503240060 Φ8 Hose Φ10 Hose 606010007 606010008 Φ12 Hose 606010009 Picture Size Φ8, Φ5 Applicable Car Type Φ10, General type (TOYOTA, MITSUBISHI SPACE WAGON GLXI) LEXUS ES300, HONDA and NISSAN car type Φ8 Φ10 Φ12 General type (TOYOTA, MITSUBISHI SPACE WAGON HONDA and NISSAN GLXI) LEXUS ES300 M16×1.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual No.
CAT-601S Auto Transmission Cleaner and Fluid Exchanger User’s Manual Warranty Order Information THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE SMARTSAFE PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. Replaceable parts can be ordered directly from your SMARTSAFE authorized tool supplier.
