Installation Instructions

1
2 2
1
2 2
1
使用
USE
将电子设备平行于真空吸盘头,并用力推向吸盘,
Place the electronic device parallel to the vacuum suction head and push it firmly against the suction cup.
2
静置1秒,待电子设备吸紧后。即可松开手进行使用
Let it stand for 1 second, and wait for the electronic equipment to suck tightly. Release your hand for use.
静电膜粘贴稳固平整后。进行步骤①使用。
After the electrostatic film is pasted firmly and smoothly. Use step .
背面不平整或者背面漏气的电子设备, 可粘贴赠送的静电膜。
For electronic equipment with uneven back or air leakage at the back, Free electrostatic film can be pasted.
4
3
1
需要移除电子设备时,按压吸盘中间按键,即可轻松取下电子设备。(注意请勿强拔)
When the electronic device needs to be removed, press the button in the middle of the suction cup to easily
remove the electronic device. (please do not pull it forcibly)
2
MATTERS
NEEDING
ATTENTION
注意事项
a.In case of uneven back or air leakage of electronic equipment, please use electrostatic film, or use a flat and
smooth protective sleeve for electronic equipment.
b.Please do not pull the electronic device after it is firmly sucked. Please use the release button to remove it.
c.Do not absorb heavy objects more than 5kg.
d.Clean the suction cup surface regularly to avoid dust affecting the suction.
a.如遇电子设备背部不平整或者漏气, 请配套使用静电膜,避免电子设备跌落。
b.电子设备吸紧后, 请勿进行拉拔, 取下请使用释放按钮。
c.请勿吸附超过5kg的重物。
d.定期清洁吸盘表面,避免灰尘影响吸力。
调节
ADJUST
使用时, 吸盘可进行360度旋转, 根据使用需求自由调节。
When in use, the suction cup can rotate 360
degrees and can be adjusted freely according
to the use demand.
3636
3
1 2 3 4
逆时针旋转旋钮,松开夹子;
安装
INSTALL
Turn the knob counterclockwise to
release the clip;
安装
INSTALL
插入空调出风口,然后顺时针锁紧旋钮;
Insert the air conditioner outlet, and
then lock the knob clockwise;
确认是否松动,安装完毕.
Conrm whether it is loose and the
installation is complete.
360° ADJUSTABLE
After the bracket is installed, use USB-A to USB-C or USB-C to USB-C to access the charging port of the
bracket. The indicator light of the bracket is on. Put the mobile phone on to realize wireless fast charging.
装好支架后,采用USB-A转USB-C或者USB-C转USB-C接入支架充电口,支架指示灯亮,放上手机即可实现无线快速充电。
INNOELEC
Automobile Holder
_ _
Installation Instructions
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible
for compliance could void the user s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- - Reorient or relocate the receiving antenna.
- - Increase the separation between the equipment and receiver.
- - Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- - Consult the dealer or an experienced radio/TV technician for help.
80.00 mm
80.00 mm

Summary of content (1 pages)