User's Manual

ManualsBrandsShenzhen Sanpima Technology ManualsElectrical EquipmentDesk lamp with clock

Table Of Contents

User Manual For Desk lamp with clock

Important Safety Instructions

• The instruction manual contains important operating and

maintenance instructions. For your safety, please read the manual

carefully before use.

• Do not hit or drop the unit.

• Do not expose the unit to vibration, direct sunlight, extreme

temperatures, or humidity.

• Do not disassemble the unit by yourself.

Turn on the ON/OFF switch to operate.

Summary of content (10 pages)

PAGE 1
User Manual For Desk lamp with clock Important Safety Instructions • The instruction manual contains important operating and maintenance instructions. For your safety, please read the manual carefully before use. • Do not hit or drop the unit. • Do not expose the unit to vibration, direct sunlight, extreme temperatures, or humidity. • Do not disassemble the unit by yourself. Turn on the ON/OFF switch to operate.
PAGE 2
- Model:SPM-TD08 Power Rating: 1000-2400W (10A Max) AC Input: 100-240V 50/60 Hz USB Output: 2*USB, 5V/Max 2.4A per port USB Power: 17W (total 5V3.
PAGE 3
PAGE 4
1：Control panel 1 ： AL1=alarm clock1 2 ： AL2=alarm clock2 3 ： SNOOZE / DIMMER/CLOCK 4：UP 5：DOWN 6：LED Touch contorl
PAGE 5
1.1．POWER FAILURE Install 2 AAA batteries in the battery compartment to help keep track of the time and alarm settings during a power failure or disconnection of the power cord. During battery-backup mode, the screen goes blank,time still runs and alarm goes off.lt has to be plugged in to activate the clock display. NOTE: Charging station does not support charging function during the battery backup mode.
PAGE 6
2.OPERATING INSTRUCTIONS 2.1 Time setting CIock.has.12-hour.time.format.Hold.and.press.the DIMMER/SNOOZE/CLOCK.button.for2.seconds.When.hour flashes,press UP and DOWN keys to select the hour you want.Once hour is selected,press the DIMMER/SNOOZE/CLOCK again for minute adjustment.When time is set to afternoon,screen will display PM,when time is set to morning,screen will display AM.press UP and DOWN.keys.to.select.desired.minute.press.the DIMMER/SNOOZE/CLOCK.Button.again.to.complete.the.time adjustment.
PAGE 7
2.2 Alarm Setting Hold and press AL1 button to enter the alarm setting mode,the.ln the alarm settin mode,the display keeps flashing. Press UP or DOWN to select the hour.Press AL1 button once to confirm the selected hour to enter minute setting state. Once screen flashes, press UP or DOWN to select the minute. Press AL1 once to confirm the selected minute, exit the setting mode and return to original time on clock. AL1 time will flash across display screen briefly.
PAGE 8
2.3 Extend the alarm clock (nap mode) When the AL1 is ringing, press the SNOOZE/DIMMER/CLOCK button to temporarily silence the alarm for the set duration (9 minutes is the default). The CIock stops the current ringing tone and enters the nap mode. Under this mode, AL1 is flashing. To exit nap mode, press AL1 once while the alarm is still on.
PAGE 9
2.4 Dimmer Default LED display brightness is set to maximum(Level 3) To adjust brightness:ln clock mode,shor press the SNOOZE / DIMMER / CLOCK button once, LED brightness will adjust to Leve 2 . Press SNOOZE / DIMMER/ CLOCK button again.Brightness will adjust to Level 1.Press SNOOZE / DIMMER/ CLOCK button again, and brightness will adjust to Level 0.
PAGE 10
FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.