USER MANUAL Wireless Tire Pressure Monitoring System Important! Turn on The Monitor before Installation
Customer Service: We have done our best to deliver a high-quality product and we’ll continue doing. Note Before Usage: The Tire Pressure Monitoring System has been fully matched before leaving the factory and does not require any complicated operations from you. You just need to turn on the tire pressure monitor first, and then install the sensors on the tire at the corresponding position.
Catalogue Product Introduction -------------------------------------------------------- 3 Product Precautions & Functions -------------------------------------- 3~5 Application Scope of TPMS System ---------------------------------- 5 Display Interface Introduction ------------------------------------------- 6 Air Leakage Alarm----------------------------------------------------------- 7 Low Pressure Alarm -------------------------------------------------------- 7 High Pressure Alarm -----------------------
Product Introduction: Thank you for purchasing our Tire Pressure Monitoring System (TPMS). This system is designed to provide you with additional protection when driving. It will warn the condition of the car's tires in advance. With the TPMS system installed, the pressure and temperature of the tires can be monitored in real time.
3.Generally, the tire will have natural slight air leakage, and the tire pressure will decrease with time, which is a normal phenomenon and not directly related to the installation of the product. 4.Affected by the thermal expansion and contraction of air, the air pressure is sometimes high and sometimes low during driving, which is a normal phenomenon and has no direct connection with the installation of the product. 5.
9.The system transmits signals wirelessly. Therefore, under some special environmental conditions, the system may be weakened or fail to receive the signal due to interference factors, wrong operation methods or improper installation methods.
Display Interface Introduction: Display of The Monitor Key Switching Function Description: TPY-C Charging Port / Receiver Charging Interface Power on/off M Menu Key / Confirm Key (In standby interface, hold down for 3 seconds to enter the menu mode and select the parameters to be adjusted.) The left and right keys serve as the adjustment selection key.
Abnormal / Alarm Information: Air Leakage Alarm： When the air pressure of any tire is lower than 26PSI(4-wheel vehicle)/58PSI (6-wheel vehicle) in a launch cycle, the buzzer will sound the alarm rapidly, and the corresponding tire icon, pressure data, TPMS icon and air leakage icon will flash continuously. Press any key to stop the buzzer alarm; The alarm is cleared after the leakage stops.
(Reference document: National Standard "GB/T2978-2008 Car Tire Specification, Dimensions, Pressure and Load"). For different models, please refer to the tire pressure standard values on the door post of the car or adjust it after consulting the tire shop or reading the instruction manual.
Pressure Unit Setting (Factory Default is PSI): In standby interface, hold down "Menu Key" for 3 seconds to enter system setting mode, which is PSI unit. (Refer to figure 1) Temperature Unit Setting In standby interface, hold down the "Menu Key" for 3 seconds to enter the system setting mode. Press the "Menu Key" once to enter the temperature unit setting. Select the F / C unit through the "+” / “-" button. After the temperature unit is selected, press the "Menu Key" to confirm the setting.
Tire Pressure Alarm Upper and Lower Limit Value Setting: Factory Default: High Pressure: 43PSI(4-wheel vehicle)/ 97PSI(6-wheel vehicle) Low Pressure: 26PSI(4-wheel vehicle)/ 58PSI(6-wheel vehicle) High Temperature: 70 º C Low Pressure Alarm Value Setting of Front Wheel: In standby interface, hold down the "Menu Key" for 3 seconds to enter the system setting mode. Press the "Menu Key" twice to enter low pressure alarm value setting of front wheel.
High Pressure Alarm Value Setting of Front Wheel: In standby interface, hold down the "Menu Key" for 3 seconds to enter the system setting mode. Press the "Menu Key" 3 times to enter high pressure alarm value setting of front wheel. At this time, you can set the upper limit value of high pressure through the "+” / “-" button. After the setting is confirmed, press and hold the "Menu Key" to save and exit.
High Pressure Alarm Value Setting of Rear Wheel: In standby interface, hold down the "Menu Key" for 3 seconds to enter the system setting mode. Press the "Menu Key" 5 times to enter high pressure alarm value setting of rear wheel. At this time, you can set the upper limit value of high pressure through the "+” / “-" button. After the setting is confirmed, press and hold the "Menu Key" to save and exit.
Tire Matching Setting (Inflate/Deflate Matching): In standby interface, hold down the "+" button for 3 seconds to enter the matching setting mode. Press the "+" button to enter the matching mode, as shown below: At this time, the icon of “0” in the interface flashing, press the "+" button to enter the matching mode. “1” shows 00 small wheel icon flashing, and then install the sensor #1. If the matching is successful, it will automatically enter the matching of “2”.
“5” shows 00 small wheel icon flashing, and then install the sensor #5, it will automatically enter the matching of “6”. “6” shows 00 small wheel icon flashing, and then install the sensor #6. If all tires are matched successfully, the system will automatically return to the main interface and the monitor will display the corresponding tire pressure values. The matching methods are respectively: "1" - > "2" - > "3" - > "4 >" 5 > "6", and the matching of the tire sensor is completed.
Tire Corresponding Position: 4-Wheel Tire Position 6-Wheel Tire Position 15
Basic Parameters: Monitor’s Parameters Working temperature - 20 ℃ ~ 80 ℃ Storage temperature - 30 ℃ ~ 85 ℃ Power voltage DC 5V Frequency 433.92mhz ± 20.00mhz Sensor’s Parameters Working temperature - 40 ℃ ~ 75 ℃ Storage temperature - 30 ℃ ~ 85 ℃ Pressure range 0 ~ 8bar/0~116psi Pressure accuracy + / - 0.1bar/1psi Temperature accuracy +/-3℃ Transmitting power ＜ 10dB Frequency 433.92mhz ± 20.
External Sensor Installation Method: 1.Screw nuts into the value. 2. Tighten the sensor. 3.Tighten the nut to hold on sensor with anticlockwise. 4. Use spanner to fix nut with anticlockwise. Battery Replacement Instructions: 1.Before removing the sensor, please prepare the nut wrench, rotate the nut clockwise to separate the nut and the sensor, and then remove the sensor counterclockwise; 2.Remove the anti fixing ring and unscrew the upper cover housing of the sensor counterclockwise with a wrench; 3.
FCC warning： 1. This device should be installed and operated with minimum distance 20cm between the radiator&your body. 2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 3.
