Mbps 54M/150M/300 54M/150M/300M USB WIRELESS ADAPTER User User’’s Manual (Ver 2.
Userʼs Manual Wireless USB Adapte r Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Userʼs Manual Wireless USB Adapte r 2) With a wireless adaptor, receiving and transferring signal via local AP (Access Point) or so called Hotpoint directly. Tips: An 802.11 LAN is based on a cellular architecture where the system is subdivided into cells, where each cell (called Basic Service Set or BSS) is controlled by a Base Station (called Access Point, or in short AP). 2. Package Contents: � One 54 Mbps 802.11b/g or 150Mbps or 300Mbps 802.11n USB Wireless Adapter. � Adapter Installation disc.
Userʼs Manual Wireless USB Adapte r b. There shows a setup type window, you can select “Install driver only” or “Install driver and Ralink WLAN utility” and then click the “Next”. Tips Tips:: i. The Windows XP utilizes a "Wireless Zero Configuration( WZC)" Service built into the operating system. Many wireless network adapter cards utilize this service. ii. Ralink- the chipset manufacturer has developed a utility for setting up wireless connection.
Userʼs Manual d. Click “finish” to finish the driver installation.
Userʼs Manual Wireless USB Adapte r For Windows 7: Once the wireless USB adapter be plugged into an USB port, the following message will appear on screen. The following installation procedures are similar to those of Windows XP. Please refer to the installation steps for Windows XP. 4. Wireless Connection For Windows XP: 1) After finishing driver installation, insert the USB adapter to Notebook or PC that supports USB 2.0/1.1 interface.
Userʼs Manual Wireless USB Adapte r Notes: Before configuring your WiFi access, you need to have your network’s SSID (service set identifier), security key and authentication type handy. Check the documentation coming with your router, ask your network administrator to get the information. 3) If you don't see your network, click “Refresh network list” in the upper left corner.
Userʼs Manual Wireless USB Adapte r decided by you. Then clicking the Connecting, your default Internet browser will launch and take you to the service provider’s login page. Most providers have very simple and step-by-step instructions for you to sign up and then to be connected. Another way to access the service provider’s login page is to simply launch your Internet browser, if there’s a pay network available, you’ll be taken directly to the login page.
Userʼs Manual Wireless USB Adapte r � Station mode (Client mode) : It is the default access way, the USB wireless adapter servers as a client to access Internet through other router or AP. � AP mode: It sets the USB wireless adapter as an AP, which allows the other users can connect to Internet through your computer. Before using the mode, it must be available that an existed Internet connection via wire Ethernet connection or by 3G wireless connection.
Userʼs Manual Wireless USB Adapte r v. The Ralink Utility automatically detects and displays the security settings of the network to which you are connecting in the Profile Settings screens.If the Utility shows that WPA-PSK or WPA2-PSK security is detected as shown below, click the right arrow to save your settings. vi. In the screen that displays, in the 'WPA Preshared Key' field, type a security key, the same as that used by the AP or wireless router to which you are connecting.
Userʼs Manual Wireless USB Adapte r For Windows 7: s: Windows Zero Configuration (WZC) is not necessary in Windows Vista, Windows 7, or Note Notes higher version OS, you can use WZC and the Ralink Utility to manage the adapter simultaneously. 1) Click on the wireless networks icon in the task bar in the bottom right hand corner of your screen to display the available wireless networks. 2) Click the "Connect" button to connect to the selected network.
Userʼs Manual Wireless USB Adapte r 3) If your network has wireless security configured, enter the required settings. The following is an example only, your network settings may differ. 4) The success of your connection is indicated by the wireless networks icon. Notes: The steps of using the Ralink Utility to connect a wireless network is the same as those described in Windows XP.
Userʼs Manual Wireless USB Adapte r well. Which means: other wireless devices connect to � Soft-AP of the adapter � the adapter (client mode with internal ICS sharing) � connect to other AP or router� Internet. This mode lets you use the adapter both as a Soft-AP and client at the same time. Switching to this mode, you can let a wireless adapter be connected to a wireless network (Soft-AP) with Internet connected, and let others adapter be indirectly connect to Internet via the Soft-AP wireless network.
Userʼs Manual Wireless USB Adapte r 5. Tips for Wi-Fi users With a Wi-Fi connection, you can roam about 150 m around the access point (depends on different environment), so find a spot where you can work without any interruption. Then see how much work you can do, such as: � Easily and quickly receive and transmit files within your local network — no problem for big files. � Access your email and surf the web with the same speed as that connected with network cables.
Userʼs Manual Wireless USB Adapte r 9. Specifications (Typical): Protocol and Standards IEEE 802.11b/g or 802.11n Interface USB1.1, USB2.0 Frequency Band 2.412~2.4835GHz (Depends on different countries’ regulation) For 802.11b/g: Peak rate 54Mbps, Peak throughput: 27Mbps. Data Rate For 802.11n 1T1R. Peak rate: 150Mbps, Peak throughput: 90Mbps 1T2R. Peak rate: 300Mbps, Peak throughput: Rx 160Mbps 2T2R. Peak rate: 300Mbps, Peak throughput: Rx 260Mbps Transmit Power (Typical) 802.11b: 19dBm; 802.
