User's Manual
Table Of Contents
- 1 Safety
- 2 General Product Description
- 3 Getting Started
- 3.1 Unpacking and Checking
- 3.2 Environmental Requirements
- 3.3 Connecting the ECG Leadwire
- 3.4 Installing the Batteries
- 3.5 Powering On the Unit
- 3.6 Understanding Touch Gestures
- 3.7 Basic Operations
- 3.7.1 Understanding the Screen Display Orientation
- 3.7.2 Browsing the Screen Display
- 3.7.3 Switching the Screen Display Orientation
- 3.7.4 Flipping the Landscape Display
- 3.7.5 Displaying the Quick Keys Area
- 3.7.6 Entering the Main Menu
- 3.7.7 Turning the Display Off
- 3.7.8 Turning the Display On
- 3.7.9 Unlocking the Screen
- 3.7.10 Acknowledging the Nurse Call
- 3.8 Using the Pouch
- 4 User Configurations
- 5 Patient Management
- 6 Alarms
- 7 Monitoring ECG
- 7.1 Introduction
- 7.2 Safety
- 7.3 Preparation for Monitoring ECG
- 7.4 Changing the ECG Settings
- 7.5 Understanding the ECG Display
- 8 Monitoring SpO2 (Optional)
- 9 Monitoring with the TD60 at the CS
- 9.1 Introduction
- 9.2 Physiological Alarms
- 9.3 ECG Monitoring
- 9.4 QT Monitoring
- 9.5 ST Monitoring
- 9.6 Arrhythmia Monitoring
- 9.7 SpO2 Monitoring
- 10 Configuring the TD60
- 10.1 Introduction
- 10.2 Maintenance Menu
- 10.2.1 Entering the Maintenance menu
- 10.2.2 Configuring the General Menu
- 10.2.3 Configuring the Alarms Menu
- 10.2.4 Quick Keys Menu
- 10.2.5 Configuring the Defaults Menu
- 10.2.6 Transferring a Configuration
- 10.2.7 Screen Lock Menu
- 10.2.8 Changing the Passwords
- 10.2.9 Changing the Device Name
- 10.2.10 Demo Mode
- 10.2.11 Service Menu
- 11 Battery
- 12 Troubleshooting
- 13 Cleaning and Disinfecting
- 14 Maintenance
- 15 Accessories
- A Product Specifications
- B EMC
- D Symbols and Abbreviations
- E Anomaly
Monitoring with the TD60 at the CS ECG Monitoring
TMS60 Operator’s Manual 9 - 13
9.3.2 Waveform Setup
The ECG leads waveforms displayed in the waveform area are defined as the displaying
lead.
The CS uses information from two leads to detect beats and to compute HR. These two
leads are referred to as the primary and secondary leads. In addition, for Mortara ECG
algorithm, information from an additional lead (analysis lead) is made use of to classify
the beats (normal, abnormal etc). The user can select any of the available leads (depend-
ing on whether a 3 or 5 lead cable is used) as primary, secondary or other analysis leads.
For best results, the following guidelines should be used:
■ The QRS complex should be tall, narrow and preferably either completely above or
below the baseline. If at all possible, avoid selecting a lead where the QRS complex
is biphasic.
■ The P-waves and T-waves should be small compared to the QRS. They should be
less than about 0.2 mV.
9.3.2.1 Changing the Setting for Analysis Leads and Displaying Leads
The default system setting for the analysis leads and displaying leads is [On], which
means that the analysis leads are consistent with the displaying leads. You can change
the default setting as following steps, if necessary.
1. At the CS, click [Admin Setup] → input the password → [OK].
2. In the [Admin Setup] menu, click the [Te le me tr y] tab.
3. On the left side of the [Telem etr y] tab, click [Analysis Lead Setting].
The corresponding setting displays to the right of [Te le me tr y].
4. Set [Consistent with Displayed Lead] to [On] or [Off].
◆ [On]: the analysis lead is the same as the displaying lead.
◆ [Off]: the analysis lead is different from the displaying lead.
HR Record on Alarm Select whether or not to activate the
option to direct the CS to send the HR
alarm data to the configured recorder.
On, Off
Waveform Setup Select to display the [Waveform Setup]
menu.
Refer to "Waveform Setup" on
page 9 - 13 for details.
Other Settings Select to display the [Other Settings]
menu.
Refer to "Other Settings" on page
9 - 15 for details.
Options or Buttons Description Settings*
* The factory default settings are in bold.