User's Manual

ManualsBrandsShenzhen Mindray BIO-Medical electronics ManualsElectronicsTelemetry transmitter

Table Of Contents

1 Safety
- 1.1 Safety Information
- 1.2 Equipment Symbols
2 General Product Description
- 2.1 Intended Use
- 2.2 Applied Parts
- 2.3 Key Features
- 2.4 System Components
- 2.5 TD60 Physical View
- 2.6 Antenna Array
- 2.7 Telemetry Receiver (RC60)
- 2.8 Touch Screen Display
  - 2.8.1 Display Screen
  - 2.8.2 On-Screen Keyboard
    - 2.8.2.1 Alphabetic Keyboard
    - 2.8.2.2 Numeric Keyboard
3 Getting Started
- 3.1 Unpacking and Checking
- 3.2 Environmental Requirements
- 3.3 Connecting the ECG Leadwire
- 3.4 Installing the Batteries
  - 3.4.1 Installing the Lithium-ion Rechargeable Battery
  - 3.4.2 Installing the AA Batteries
- 3.5 Powering On the Unit
- 3.6 Understanding Touch Gestures
- 3.7 Basic Operations
- 3.8 Using the Pouch
  - 3.8.1 Securing the Pouch
4 User Configurations
- 4.1 Introduction
- 4.2 Configuring the Display
- 4.3 Configuring the Audio Volume
5 Patient Management
- 5.1 Introduction
- 5.2 Admitting a Patient
- 5.3 Changing the Patient Category
- 5.4 Placing a Device in Standby
- 5.5 Resume Monitoring
- 5.6 Discharging the Patient
  - 5.6.1 Selecting the Discharge Patient menu
  - 5.6.2 Restarting the TD60
6 Alarms
- 6.1 Introduction
- 6.2 Alarm Categories
- 6.3 Alarm Levels
- 6.4 Alarm Indicators
- 6.5 Configuring the Alarms
- 6.6 Resetting the Alarms
7 Monitoring ECG
- 7.1 Introduction
- 7.2 Safety
- 7.3 Preparation for Monitoring ECG
- 7.4 Changing the ECG Settings
- 7.5 Understanding the ECG Display
8 Monitoring SpO2 (Optional)
- 8.1 Introduction
- 8.2 Measurement Limitations
- 8.3 Safety
- 8.4 Connecting the SpO2 Module
- 8.5 Changing the SpO2 Settings
  - 8.5.1 Configuring the SpO2 Setup
  - 8.5.2 Configuring the SpO2 Waveform
- 8.6 SpO2 Measurement
  - 8.6.1 Identifying SpO2 Modules
  - 8.6.2 Applying the Sensor
- 8.7 Understanding the SpO2 Display
- 8.8 Masimo Information
9 Monitoring with the TD60 at the CS
- 9.1 Introduction
- 9.2 Physiological Alarms
- 9.3 ECG Monitoring
- 9.4 QT Monitoring
- 9.5 ST Monitoring
- 9.6 Arrhythmia Monitoring
- 9.7 SpO2 Monitoring
10 Configuring the TD60
- 10.1 Introduction
- 10.2 Maintenance Menu
11 Battery
- 11.1 Introduction
- 11.2 Safety
- 11.3 Installing the Battery
- 11.4 Checking the Battery Charge Status
- 11.5 Removing the Battery
- 11.6 Charging the Rechargeable Lithium-ion Battery
- 11.7 Storing the Batteries
  - 11.7.1 Storing Rechargeable Lithium-ion Battery
  - 11.7.2 Storing AA Batteries
- 11.8 Maintaining the Rechargeable Lithium-ion Battery
- 11.9 Disposing of the Batteries
  - 11.9.1 Disposing of the Rechargeable Lithium-ion Battery
  - 11.9.2 Disposing of the AA Batteries
12 Troubleshooting
- 12.1 General Problems
  - 12.1.1 Troubleshooting Tools
  - 12.1.2 Problem List
- 12.2 Physiological Alarm Messages at the CS
- 12.3 Technical Alarm Messages at the TD60
13 Cleaning and Disinfecting
- 13.1 Introduction
- 13.2 Safety Information
- 13.3 Cleaning of the TD60
- 13.4 Cleaning the Reusable ECG Leadwires, SpO2 Modules and Sensors
- 13.5 Cleaning the Battery and Battery Compartment
- 13.6 Disinfection
- 13.7 Sterilization
14 Maintenance
- 14.1 Introduction
- 14.2 Safety
- 14.3 Regular Check
  - 14.3.1 Power-on Test
  - 14.3.2 Battery Check
- 14.4 Maintenance and Testing Schedule
- 14.5 Checking the System Information
- 14.6 Verifying the ECG at the TD60
15 Accessories
- 15.1 ECG Accessories
  - 15.1.1 ECG Electrodes
  - 15.1.2 ECG Leadsets
- 15.2 SpO2 Accessories
- 15.3 Miscellaneous
A Product Specifications
- A.1 Classifications
- A.2 Environmental Specifications
- A.3 Power Supply Specifications
- A.4 Physical Specifications
- A.5 Hardware Specifications
- A.6 WMTS Specification
- A.7 Mindray Patient Area Network (MPAN) Specification
- A.8 Measurement Specifications
  - A.8.1 ECG
  - A.8.2 SpO2
B EMC
C FCC Compliance
D Symbols and Abbreviations
- D.1 Units
- D.2 Symbols
- D.3 Abbreviations
E Anomaly
- E.1 Anomaly Description

Monitoring SpO2 (Optional) Changing the SpO2 Settings

TMS60 Operator’s Manual 8 - 5

Connecting the Nonin SpO

module

8.5 Changing the SpO

Settings

You can change the SpO

settings from the SpO

menu.

8.5.1 Configuring the SpO

Setup

Enter the SPO

menu in either of the following ways:

■ On the main screen, tap the SpO

digital area or SpO

waveform area to enter the

SpO

menu.

■ In the main menu, tap Parameter Setup → SpO

to enter the SpO

menu.

1. In the Setup section of the SpO

menu, select the options described in the follow-

ing table.

SpO

module

SpO

sensor

SpO

sensor connector