User's Manual

ManualsBrandsShenzhen Mindray BIO-Medical electronics ManualsElectronicsTelemetry transmitter

Table Of Contents

1 Safety
- 1.1 Safety Information
- 1.2 Equipment Symbols
2 General Product Description
- 2.1 Intended Use
- 2.2 Applied Parts
- 2.3 Key Features
- 2.4 System Components
- 2.5 TD60 Physical View
- 2.6 Antenna Array
- 2.7 Telemetry Receiver (RC60)
- 2.8 Touch Screen Display
  - 2.8.1 Display Screen
  - 2.8.2 On-Screen Keyboard
    - 2.8.2.1 Alphabetic Keyboard
    - 2.8.2.2 Numeric Keyboard
3 Getting Started
- 3.1 Unpacking and Checking
- 3.2 Environmental Requirements
- 3.3 Connecting the ECG Leadwire
- 3.4 Installing the Batteries
  - 3.4.1 Installing the Lithium-ion Rechargeable Battery
  - 3.4.2 Installing the AA Batteries
- 3.5 Powering On the Unit
- 3.6 Understanding Touch Gestures
- 3.7 Basic Operations
- 3.8 Using the Pouch
  - 3.8.1 Securing the Pouch
4 User Configurations
- 4.1 Introduction
- 4.2 Configuring the Display
- 4.3 Configuring the Audio Volume
5 Patient Management
- 5.1 Introduction
- 5.2 Admitting a Patient
- 5.3 Changing the Patient Category
- 5.4 Placing a Device in Standby
- 5.5 Resume Monitoring
- 5.6 Discharging the Patient
  - 5.6.1 Selecting the Discharge Patient menu
  - 5.6.2 Restarting the TD60
6 Alarms
- 6.1 Introduction
- 6.2 Alarm Categories
- 6.3 Alarm Levels
- 6.4 Alarm Indicators
- 6.5 Configuring the Alarms
- 6.6 Resetting the Alarms
7 Monitoring ECG
- 7.1 Introduction
- 7.2 Safety
- 7.3 Preparation for Monitoring ECG
- 7.4 Changing the ECG Settings
- 7.5 Understanding the ECG Display
8 Monitoring SpO2 (Optional)
- 8.1 Introduction
- 8.2 Measurement Limitations
- 8.3 Safety
- 8.4 Connecting the SpO2 Module
- 8.5 Changing the SpO2 Settings
  - 8.5.1 Configuring the SpO2 Setup
  - 8.5.2 Configuring the SpO2 Waveform
- 8.6 SpO2 Measurement
  - 8.6.1 Identifying SpO2 Modules
  - 8.6.2 Applying the Sensor
- 8.7 Understanding the SpO2 Display
- 8.8 Masimo Information
9 Monitoring with the TD60 at the CS
- 9.1 Introduction
- 9.2 Physiological Alarms
- 9.3 ECG Monitoring
- 9.4 QT Monitoring
- 9.5 ST Monitoring
- 9.6 Arrhythmia Monitoring
- 9.7 SpO2 Monitoring
10 Configuring the TD60
- 10.1 Introduction
- 10.2 Maintenance Menu
11 Battery
- 11.1 Introduction
- 11.2 Safety
- 11.3 Installing the Battery
- 11.4 Checking the Battery Charge Status
- 11.5 Removing the Battery
- 11.6 Charging the Rechargeable Lithium-ion Battery
- 11.7 Storing the Batteries
  - 11.7.1 Storing Rechargeable Lithium-ion Battery
  - 11.7.2 Storing AA Batteries
- 11.8 Maintaining the Rechargeable Lithium-ion Battery
- 11.9 Disposing of the Batteries
  - 11.9.1 Disposing of the Rechargeable Lithium-ion Battery
  - 11.9.2 Disposing of the AA Batteries
12 Troubleshooting
- 12.1 General Problems
  - 12.1.1 Troubleshooting Tools
  - 12.1.2 Problem List
- 12.2 Physiological Alarm Messages at the CS
- 12.3 Technical Alarm Messages at the TD60
13 Cleaning and Disinfecting
- 13.1 Introduction
- 13.2 Safety Information
- 13.3 Cleaning of the TD60
- 13.4 Cleaning the Reusable ECG Leadwires, SpO2 Modules and Sensors
- 13.5 Cleaning the Battery and Battery Compartment
- 13.6 Disinfection
- 13.7 Sterilization
14 Maintenance
- 14.1 Introduction
- 14.2 Safety
- 14.3 Regular Check
  - 14.3.1 Power-on Test
  - 14.3.2 Battery Check
- 14.4 Maintenance and Testing Schedule
- 14.5 Checking the System Information
- 14.6 Verifying the ECG at the TD60
15 Accessories
- 15.1 ECG Accessories
  - 15.1.1 ECG Electrodes
  - 15.1.2 ECG Leadsets
- 15.2 SpO2 Accessories
- 15.3 Miscellaneous
A Product Specifications
- A.1 Classifications
- A.2 Environmental Specifications
- A.3 Power Supply Specifications
- A.4 Physical Specifications
- A.5 Hardware Specifications
- A.6 WMTS Specification
- A.7 Mindray Patient Area Network (MPAN) Specification
- A.8 Measurement Specifications
  - A.8.1 ECG
  - A.8.2 SpO2
B EMC
C FCC Compliance
D Symbols and Abbreviations
- D.1 Units
- D.2 Symbols
- D.3 Abbreviations
E Anomaly
- E.1 Anomaly Description

Introduction User Configurations

4 - 2 TMS60 Operator’s Manual

4.1 Introduction

This chapter describes the configurations available for users to do, such as configuring

the Display Setup, and Audio Volume.

4.2 Configuring the Display

You can configure the display by setting the display layout, display orientation, and

screen brightness.

In the main menu, tap Display Setup to enter the Display Setup menu.

4.2.1 Setting the Default Display Orientation

For details about the display orientation, refer to "Understanding the Screen Display

Orientation" on page 3 - 10.

1. In the Setup section of the Display Setup menu, tap Default Orientation.

Two buttons display: Portrait and Landscape.

2. Tap a button to set the default orientation.

The selected orientation displays to the right of Default Orientation.

3. Restart the TD60 to apply the setting.

4.2.2 Understanding Portrait Orientation Display Rules

In portrait orientation, both digital and waveform areas take up the entire width of the

screen. Therefore, these parameters will be displayed in the exact order of the Display

Setup menu, provided the sensor is attached and monitoring data.

4.2.3 Setting the Portrait Display

1. In the Portrait section of the Display Setup menu, tap Rows.

Three options display: 2, 3, and 4.

2. Tap an option to set the row numbers.

The selected option displays to the right of Rows.

3. Tap Portrait Order to enter the Portrait Order menu.

4. Tap a parameter or waveform to select it.

The icon displays to the right of the selected parameter or waveform.

5. Drag the selected parameter or waveform to the desired position, and then release

it.

6. Repeat steps 4 and 5 until the desired order is configured.

7. Tap the icon to exit the Portrait Order menu.