User's Manual

ManualsBrandsShenzhen Mindray BIO-Medical electronics ManualsElectronicsTelemetry transmitter

111

112

113

114

115

116

117

118

119

120

Table Of Contents

1 Safety
- 1.1 Safety Information
- 1.2 Equipment Symbols
2 General Product Description
- 2.1 Intended Use
- 2.2 Applied Parts
- 2.3 Key Features
- 2.4 System Components
- 2.5 TD60 Physical View
- 2.6 Antenna Array
- 2.7 Telemetry Receiver (RC60)
- 2.8 Touch Screen Display
  - 2.8.1 Display Screen
  - 2.8.2 On-Screen Keyboard
    - 2.8.2.1 Alphabetic Keyboard
    - 2.8.2.2 Numeric Keyboard
3 Getting Started
- 3.1 Unpacking and Checking
- 3.2 Environmental Requirements
- 3.3 Connecting the ECG Leadwire
- 3.4 Installing the Batteries
  - 3.4.1 Installing the Lithium-ion Rechargeable Battery
  - 3.4.2 Installing the AA Batteries
- 3.5 Powering On the Unit
- 3.6 Understanding Touch Gestures
- 3.7 Basic Operations
- 3.8 Using the Pouch
  - 3.8.1 Securing the Pouch
4 User Configurations
- 4.1 Introduction
- 4.2 Configuring the Display
- 4.3 Configuring the Audio Volume
5 Patient Management
- 5.1 Introduction
- 5.2 Admitting a Patient
- 5.3 Changing the Patient Category
- 5.4 Placing a Device in Standby
- 5.5 Resume Monitoring
- 5.6 Discharging the Patient
  - 5.6.1 Selecting the Discharge Patient menu
  - 5.6.2 Restarting the TD60
6 Alarms
- 6.1 Introduction
- 6.2 Alarm Categories
- 6.3 Alarm Levels
- 6.4 Alarm Indicators
- 6.5 Configuring the Alarms
- 6.6 Resetting the Alarms
7 Monitoring ECG
- 7.1 Introduction
- 7.2 Safety
- 7.3 Preparation for Monitoring ECG
- 7.4 Changing the ECG Settings
- 7.5 Understanding the ECG Display
8 Monitoring SpO2 (Optional)
- 8.1 Introduction
- 8.2 Measurement Limitations
- 8.3 Safety
- 8.4 Connecting the SpO2 Module
- 8.5 Changing the SpO2 Settings
  - 8.5.1 Configuring the SpO2 Setup
  - 8.5.2 Configuring the SpO2 Waveform
- 8.6 SpO2 Measurement
  - 8.6.1 Identifying SpO2 Modules
  - 8.6.2 Applying the Sensor
- 8.7 Understanding the SpO2 Display
- 8.8 Masimo Information
9 Monitoring with the TD60 at the CS
- 9.1 Introduction
- 9.2 Physiological Alarms
- 9.3 ECG Monitoring
- 9.4 QT Monitoring
- 9.5 ST Monitoring
- 9.6 Arrhythmia Monitoring
- 9.7 SpO2 Monitoring
10 Configuring the TD60
- 10.1 Introduction
- 10.2 Maintenance Menu
11 Battery
- 11.1 Introduction
- 11.2 Safety
- 11.3 Installing the Battery
- 11.4 Checking the Battery Charge Status
- 11.5 Removing the Battery
- 11.6 Charging the Rechargeable Lithium-ion Battery
- 11.7 Storing the Batteries
  - 11.7.1 Storing Rechargeable Lithium-ion Battery
  - 11.7.2 Storing AA Batteries
- 11.8 Maintaining the Rechargeable Lithium-ion Battery
- 11.9 Disposing of the Batteries
  - 11.9.1 Disposing of the Rechargeable Lithium-ion Battery
  - 11.9.2 Disposing of the AA Batteries
12 Troubleshooting
- 12.1 General Problems
  - 12.1.1 Troubleshooting Tools
  - 12.1.2 Problem List
- 12.2 Physiological Alarm Messages at the CS
- 12.3 Technical Alarm Messages at the TD60
13 Cleaning and Disinfecting
- 13.1 Introduction
- 13.2 Safety Information
- 13.3 Cleaning of the TD60
- 13.4 Cleaning the Reusable ECG Leadwires, SpO2 Modules and Sensors
- 13.5 Cleaning the Battery and Battery Compartment
- 13.6 Disinfection
- 13.7 Sterilization
14 Maintenance
- 14.1 Introduction
- 14.2 Safety
- 14.3 Regular Check
  - 14.3.1 Power-on Test
  - 14.3.2 Battery Check
- 14.4 Maintenance and Testing Schedule
- 14.5 Checking the System Information
- 14.6 Verifying the ECG at the TD60
15 Accessories
- 15.1 ECG Accessories
  - 15.1.1 ECG Electrodes
  - 15.1.2 ECG Leadsets
- 15.2 SpO2 Accessories
- 15.3 Miscellaneous
A Product Specifications
- A.1 Classifications
- A.2 Environmental Specifications
- A.3 Power Supply Specifications
- A.4 Physical Specifications
- A.5 Hardware Specifications
- A.6 WMTS Specification
- A.7 Mindray Patient Area Network (MPAN) Specification
- A.8 Measurement Specifications
  - A.8.1 ECG
  - A.8.2 SpO2
B EMC
C FCC Compliance
D Symbols and Abbreviations
- D.1 Units
- D.2 Symbols
- D.3 Abbreviations
E Anomaly
- E.1 Anomaly Description

Monitoring with the TD60 at the CS ST Monitoring

TMS60 Operator’s Manual 9 - 25

3. Select the OK or Cancel button.

◆ The OK button saves the settings and closes the menu.

◆ The Cancel button closes the menu without saving the settings.

9.5.4 ST Display

When ST Analysis is enabled, the ST digital area displays:

1. Area name

2. Activation State Off icon for ST alarm

3. ST values

4. Units of measure

5. Lead identifier

Example 5-lead ST digital area

ISO/J Selecting Auto fixes the ISO and J/ST

points.

Selecting Manual allows the clinician to

manually adjust ISO and J/ST points.

Auto, Manual

ISO left arrow If ISO/J is set to manual, the button adjusts the ISO reference line to the left.

ISO right arrow If ISO/J is set to manual, the button adjusts the ISO reference line to the right.

J left arrow If ISO/J is set to manual, the button adjusts the J reference line to the left.

J right arrow If ISO/J is set to manual, the button adjusts the J reference line to the right.

Buttons Description Settings*

* The factory default settings are in bold.