User's Manual

ManualsBrandsShenzhen Liangming Technology ManualsElectronicsWireless module

Table Of Contents

User Manual

Model No. : LM80P2-0001AA, LM80S2-0001AA,

Test Model No. : LM80P2-0001AA

Company Name: Shenzhen Liangming Technology Co., Ltd.

Address: 808, Building 1, Optoelectronic R&D Building, Hangcheng

Avenue, Xixiang Street, Baoan District, Shenzhen,China

1. Overview

The LM80 SoC features a fully integrated 2.4GHz radio transceiver

and baseband processor for Wi-Fi 802.11b and Bluetooth® Smart

applications. The SoC can be used as a standalone application-specific

communication processor or as a wireless data link in hosted MCU

systems where ultra-low power is critical. The OPL1000 supports flexible

memory architecture for storing profiles, stacks and custom application

codes, and can be updated using Over-The-Air (OTA)technology.

Qualified Bluetooth Smart protocol stack and Wi-Fi TCP/IP stack are

stored in a dedicated ROM. The OPL1000 is equipped with dual

processors, ARM® Cortex®-M0 and M3, for handling different

processes. All software runs on the ARM® Cortex®-M0 processor while

more intensive application-specific activities run on the ARM®

Cortex®-M3 processor. The OPL1000 can be connected to any external

MCU through SPI, I2C or UART interfaces and sensors or other devices

through GPIOs. The transceiver interfaces directly to the antenna and is

fully compliant with the Wi-Fi 802.11b and Bluetooth 5.0 BLE standards.

Summary of content (6 pages)

PAGE 1
User Manual Model No. : LM80P2-0001AA, LM80S2-0001AA, Test Model No. : LM80P2-0001AA Company Name: Shenzhen Liangming Technology Co., Ltd. Address: 808, Building 1, Optoelectronic R&D Building, Hangcheng Avenue, Xixiang Street, Baoan District, Shenzhen,China 1. Overview The LM80 SoC features a fully integrated 2.4GHz radio transceiver and baseband processor for Wi-Fi 802.11b and Bluetooth® Smart applications.
PAGE 2
With integrated antenna switch, RF balun,power amplifier (PA) and low noise amplifier (LNA), the OPL1000 allows both Wi-Fi and Bluetooth Smart to minimize PCB design area and external component requirement. 2. FEATURES The OPL1000 complies with ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15(US), and ARIB STD-T66 (Japan). ◼ Processors ⚫ARM® Cortex®-M3 Application Processor ⚫ARM® Cortex®-M0 Link Controller ◼ Wi-Fi ⚫ 802.
PAGE 3
capability ⚫ Slave ⚫ All mode support GATT-based profiles supported ⚫ Built-in ⚫0 BLE stack to 10 dBm transmit output power ⚫ -93 dBm receive sensitivity ◼ HW Crypto Engine ⚫ AES-128/256 ⚫ P-192/256 bits Encryption ECDH (Elliptic Curve Diffie-Hellman) Key Generation ⚫ SHA2 ⚫ TRNG ◼ Power Management ⚫ Integrated ◼ General ◼ FW Buck DC-DC converter purpose, capture and sleep timers OTA (Over-The-Air) update support ◼ Digital Interfaces ⚫ General ⚫ Two UARTs with hardware flow control up
PAGE 4
⚫ Six GPIO pins with 16mA driving capability ⚫ Six PWMs ◼ Radio ⚫ Fully Transceiver integrated dual-mode 2.4 GHz CMOS transceiver ⚫ Single wire antenna: no external matching and no external T/R switch required ◼ Package ⚫ 48-pin QFN, 6 mm x 6 mm 3.
PAGE 5
FCC Modular Usage Statement The requirement for KDB 996369 D03: 2.2 List of applicable FCC rules FCC CFR Title 47 Part 15 Subpart C Section 15.247 2.3 Summarize the specific operational use conditions The module has been certified for Fix, Mobile, Portable applications. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. 2.4 Limited module procedures Not applicable 2.5 Trace antenna designs Not applicable 2.
PAGE 6
then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AQJL-LM80P2 Or Contains FCC ID: 2AQJLLM80P2” IC STATEMENT This device complies with Industry Canada’s licence-exempt RSSs.