Improve Muscle Performance & Pain Relief Electronic Pulse Stimulator Model: S3 Instruction Manual Please Read Before Using
Contents 1. Introduction ........................................................................................................3 1.1 Indications for Use ...............................................................................................3 2. Safety Precautions ..............................................................................................3 2.1 Contraindications ..................................................................................................3 2.2 Warnings ......
1. Introduction Electronic Pulse Stimulator delivers electric pulses generated to the user's skin through the electrode pad. The portable and compact device has two modes of different pulse frequencies, mode 1 uses Powered Muscle Stimulation (PMS) technology for muscle training and mode 2 uses Transcutaneous Electrical Nerve Stimulation (TENS) technology to temporary relieve pain.
1) Simultaneous connection of a PATIENT to a h.f. surgical EQUIPMENT may result in burns at the site of the STIMULATOR electrodes and possible damage to the STIMULATOR. 2) Operation in close proximity (e.g. 1m) to a shortwave or microwave therapy EQUIPMENT may produce instability the STIMULATOR output. - DO NOT use this device for purpose other than the treatment indicated in this MANUAL. It may lead to accident, problems, or failure of the device.
- Do not leave the Electrode Pad attached to the skin after treatment. Prolonged attachment may cause skin irritation or infection. - Be careful not to allow any metal object, such as a belt buckle or necklace to come into contact with the Electrode Pad during treatment. - Do not use cellular phones or other electronic devices near this device. - Do not use this device to treat one region for a long time (more than 30 minutes). 2.
Symbol Meaning Type BF applied part Class II equipment Waterproof level Follow instructions for use "WEEE (Waste Electrical and Electronic Equipment)". The waste products should be handled legally. 2.
Note 1: According to different simulation-needed bodies, users can choose the type of electrode pad based on their own situation. S3 Electronic Pulse Stimulator is suitable for the simulation-needed bodies including hips, arms and legs, abdomen, and feet. Each package is only equipped with one electrode pad by default, and the users can select and purchase the type of electrode pad according to their needs.
LED indication status Function Operation LED Indication Status Power ON/OFF Press ON (Blue)/OFF Increase + Press Blink blue one time Decrease - Press Blink blue one time Mode selection Press Color change (Blue/Green) Charging / Continuous blink white Charging completion / Solid blue Non-load / Blink blue for 30 seconds ■ Accessories The following accessories are consumed parts, which are available from the after-sales: Accessory Quantity Remote control 1 (Optional) USB charging c
Number of modes 2 modes Intensity Level 15 level Safety Category BF type Service Life (Use Life) 1 year Output Specifications Waveform and Shape Symmetrical rectangular Maximum Output Voltage (±20%) 40V@ 500 Ω 64V@ 2k Ω 76V@ 10k Ω Maximum Output Current (±20%) 80mA @ 500 Ω 32mA @ 500 Ω 7.6mA @ 10k Ω Maximum Phase Charge 22.31μC@500Ω Maximum Average Current 3.54mA@ 500 Ω Maximum Current Density (mA/cm2@500Ω) □ □ □ □ Hips pad: 0.079mA/ cm2 Arms and legs pad: 0.104mA/ cm2 Abdomen pad: 0.
Specification of Remote Control Model X5-02 Size (L×W×H) 100*30*10mm Weight (Without battery) 17.5g Power Supply Button Cell Battery Type of Wireless Technology Radio Frequency (RF) Operating Frequencies 433MHz Operating Voltage DC3V Max. Output Power 7.
4 How the Device Uses The following steps are used to guide the device operation, and the details about each step are listed in the following table 1st Step- Check the battery power for the Electronic Pulse Stimulator. Electronic Pulse Stimulator comes with a built-in rechargeable battery and could be used as received. If the battery icon is flashing when turned on, it means the battery is running out of power. Turn off and charge the controller with the enclosed USB charging cable.
3rd Step- Put the electrode pad-installed Stimulator on the stimulation-needed body area. According to different simulation-needed bodies, users can choose the type of electrode pad based on their own situation. S3 Electronic Pulse Stimulator is suitable for the simulation-needed bodies including hips, Shoulder, Low back, arms and legs, abdomen, and feet. Place the pad-installed device onto the treatment areas. Press down firmly and ensure a full and firm contact with the skin.
4th Step- Press the Power "ON/OFF" to turn on the power Press the "ON/OFF" button once to turn on the controller/ (remote control) and the controller automatically starts at level 1 intensity. LED light turns to be blue showing Mode 1. ON/OFF 5th Step- Select the treatment intensity Press the (+) button to increase the stimulation intensity and press the (-) button to decrease the intensity.
How to operate the remote control? 1) Open the battery cover behind the remote control. 2) Put the one Button Cell Battery (not included) into the battery cassette in correct polarities. 3) Close the battery cover. 4) The functions of buttons on the remote control are the same as those on the main unit (See for 3.3 details) Pad aftercare Please refer to the following use instruction for the electrode pads.
Other Functions 1) Low Voltage Indication 2) No-load Indication When the device is in low power, its LED light will flash to remind you. If there is no load, its LED light will flash and then to be turned off. Battery charged 1) Plug in the controller through micro USB charging cable (included); 2) Connect the USB charging cable with AC/DC adapter (not included); 3) The LED light on the main unit will turn white while it's being charged.
Problem Possible Cause Solution The device fails to work Is the battery low power or no power? Recharge the battery. The buttons fail to work Are the buttons damaged or contact undesirable? Make sure the device has enough power firstly;If the buttons fail to work under enough power, please contact our after-sales service for repair. The LED fails to work Is there no power or LED damaged? Recharge the battery.
FCC Caution： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
