INSTRUCTION MANUAL PT8100 VHF/UHF MOBILE RADIO
Memo： INSTRUCTION MANUAL PT8100 VHF/UHF MOBILE RADIO MANDATORY SAFETY INSTRUCTIONS TO INSTAL-LERS AND USERS ● Use Only manufacturer or dealer supplied antennas. ● Antenna minimum safe distance: 108 cm. ● Antennas used for this transmitter must not exceed an antenna gain of 3 dBi. The FCC (Federal Communications Commission) has adopted a safety standard for human exposure to RF energy which is below the OSHA (Occupational Safety and Health Act) limits.
Closer than the above indicated minimum safe distance to the antenna (i.e. 108cm). ● To comply with current FCC RF Exposure limitations, the antenna must be installed at or exceeding the minim--um safe distance indicated above, and in accordance with the requirements to the antenna manufacturer or supplier. ● Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid if the minim-um safe distance is observed.
CONTENTS Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 1. 2. 3. 4. 5. Package-opened Inspection and Installing.........................1 Radio Overview..................................................................3 Basic Operation..................................................................6 Programmable Button Function..........................................7 Radio Call.................
1. Package-opened Inspection and Installing Please check the radio in the package and the supplied accessories in the following table before using. Any articles are found lost or damaged, please contact the distributor without delay. 1.
＊ Connect the antenna and the power cable to the radio. ＊ Install the microphone hanger at the position easy to use, with 2 M4*16 self-tapping screws. (The microphone and its cable sho-uld be fixed at the position not affecting safe driving.) ＊Connect the microphone to the microphone jack on the front panel of the radio and put it on the hanger. Note: When replacing the protective tube for the power cable, please use the one of the same specification without fail.
Display Description “H” means the transmission of signal for the radio at the high power; Call Received indicator. The radio receives a selective call/call alert. Monitor State Indicator. Scan Indicator. Talkaround Indicator. P2 OST Indicator. 3．Basic Operation ① Startup: Press the red POWER button for a long time (at least 1.
4． Programmable Button Function / Buttons ， P1 ，P2 ，P3 ， can be programmed as one of the auxiliary functions. Buttons 0.None Function Description No function 1.Channel Up Select the next channel 2.Channel Down Select the previous channel 3.Zone Up Select the next zone 4.Zone Down 11.Key lock Switch button To toggle between locking/unlocking your radio’ keypad. Select the previous zone 12.Scan Start/end the scanning function of system. 13.
Buttons 18.Monitor/Call Cancel Function Description Press this button to trigger this function and the Buttons Function Description 28.Scan List Edit Press this button, the radio will enter the fast menu CTCSS, DCS, and 2Tone/DTMF signaling will be mode for scan list edit. For details, see “Menu closed, so you can receive the signal that can't be Operation”. heard in the normal operation. Press this button again to return to the normal operation. Press this 29.
Indicator will blink orange. Icon flashes and the caller’s ID or D. Press / button until the zone name you require is appeared. name displays. E. Press P3 Press PPT button for callback. ②. Select the zone through “ZONE UP”or“ZONE DOWN”button. button for selection. 5.3 Call Alert After the radio receives the call alert, the alert tone will sound and the orange indicator flicker. icon flashes and the caller’s ID 7.
B. Press button until “UTILITY”. / 9. Scan C. Press P3 button for selection. In order to receive the calls from many channels, the radio can be D. Press programmed to scan these channels. At most there are 16 channels / button until the items you require are showed. E. Press P3 button for select. The radio will show the current setup. F. Press / button to show all items that can be set with this item. G. PressP3 button to select this setup.
9.3 Edit Scan List ⑨. Press P1 button to return to the previous operation. 9.4 Add or Delete the Channels in the Scan List A. Press the “Menu Selection/Enter” button to enter the menu mode. In a certain specific channel, you can revise the CTCSS/DCS B. Press / button until “PROG LST”. C. Press P3 button to select “SCAN LIST”. D. Press / button until “ADD LST?” or “DEL LST?”. E. Press P3 button for selection. F. Press G. / button until the channel you want to add or delete.
It will enter the user mode. Number Problem ②. Connect the slave radio with the wired clone cable first, and then 2 turn on. ③. Press the master radio's P3 for starting clone. During transmi- tting the data, the master radio lights red, and the slave radio lights green. ④. Press the Phase lock A. The crystal X1 of phase lock loop is broken, loop please replace it. unlocked B. The oscillator tube is broken, please (Beeping) replace it. C.
No. 5 Problem Solution The red transmission A.Power amplifier IC1 is broken, and no Indicator lights but no power is output, please replace it. sound is heard. Memo： B. The microphone is broken, please replace it. 6 The green receiving A. The speaker is broken. Please replace it. dictator lights but no B. The audio power amplifier TDA1519C sound is heard. is broken. Please replace IC. 13.
We, Kirisun Electronics (Shenzhen) Co., Ltd. 2/F, Bldg.H-3, East Industrial Zone Of Overseas Chinese Town, Shenzhen 518053, China Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suits measurement has been performed. Description of equipment: FM Mobile Transceiver Model No.
