INSTRUCTION MANUAL PT6500 FM HANDHELD TRANSCEIVER
NOTE INSTRUCTION MANUAL PT6500 FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand twoway radios produced by Kirisun Electronics (Shenzhen) Co., Ltd. two-way radio always incorporates the latest technology, The quality and function of the two-way radio can meet your demands for reliable communication. Notice to the User: Please read this instruction manual before operating this radio.
the areas where the government laws prohibit radio communication. Please don't expose the radio to direct sunlight for a long time; don't place the radio near any heating devices, either. Please don't put the radio in extremely dusty, moist or dabbling places; don't place it on any unstable surfaces, either. If you want to develop or remodify the radio, refer service to the well-trained professional technicians only and do not disassemble or assemble the radio.
FCC Notice Your KIRISUN radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”.
with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch. ALWAYS keep the antenna at least 2.
WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the Battery listed below Such a connection will ruin the transceiver. DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F).
CONTENTS Unpacking And Checking.............................................................1 Supplied Accessories .............................................................1 Preparation...................................................................................2 Charging the battery..................................................................2 Installing/Removing the battery pack.........................................3 Installing the antenna.................................................
PREPARATION CHARGING THE BATTERY PACK Plug the power adapter into the proper AC wall outlet; and insert the cable of the power adapter into the adapter socket on the charger; then the charger indicator lights green. Insert the battery or the radio to be charged into the charger slot. Make sure the battery is in good contact with the charger terminals. When the red indicator lights, the charger begins to charge the battery.
INSTALLING THE ANTENNA RADIO OVERVIEW Screw the antenna into the connector at the top of the transceiver by holding the Button of the antenna and turn it clockwise until secure. P1 INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE Insert the speaker/microphone plug into the jacks of the versatile connector. INSTALLING THE BELT CLIP Match the grooves of the belt clip with those on the rear of the battery. Then press belt clip downwards to lock it in place.
I. Button P1 Return and delete button in the menu. J. Button P2 Select Button. K. Button P 3 Select Button. L. Button P4 Enter and Confirm Button. M. Numeric keypad N. Microphone/speaker jacks For connecting microphone/speaker. BASIC OPERATION 1.Switch On Switch on the radio by turning the Power/Volume switch clockwise till a click is heard, then the radio will be in the state of stand by and you will hear a beep if the dealer has set it. 2.
Utilities 4. Make a Call To make a call, press PTT, and speak in normal voice. Please keep your mouth 3~4 cm away from the microphone. Scan Back Light Squelch Level ON/OFF Level: 0~9 ON/OFF Key tone Scrambler ON/OFF ON/OFF Save Companding Power Level H Whisper M L Vox ON/OFF Contact list 5. Receive a Call Release the PTT button to receive a call. Your dealer can set CTCSS, DCS, 5 Tone,DTMF,2 Tone signaling on your radio channels by PC software.
5. Change the power level with confirm. The operations are as follows: Set scanning: 1. As shown: in CH 1 , press P4 , then Utilities is shown; 2. Press P4 , to enter select mode ; 3. Press P2 / P 3 ,then Scan is shown; 4. Press P4 , then enter selecting 5. Select Scan On or Scan OFF with confirm it. P2 Scan ; / P 3 , then press P4 to If can not enter that way, you have to set in PC communications; Set back light: 1. As shown: in CH 1 , press P4 , Utilities is shown. P4 2.
1.As shown:in CH1 ,press P4 , Utilities is shown. 2.Press P4 to enter select mode. 3.Press P2 / P 3 , and VOX is shown. 4.Press P4 to select OFF or ON . 5.Select ON or OFF with P2 / P 3 ,press P4 to confirm. Set call list 1 As shown: in CH 1 , press P4 to enter select mode, 2. Press P2 / P 3 , and Call is shown, 3. Press P4 to select the call list , 4. Select with P2 / P 3 , press PTT to transmit. Set whisper 1.As shown:in CH1 ,press P4 , Utilities is shown. 2.Press P4 then Whisper is shown. 3.
1 As shown: in CH 1 , press P4 to enter select mode, 2. Press P2 / P 3 , and Ch Edit is shown, 3. Press P4 to select Ch alias CHANNEL 1 4. Press P3 , Rx CTCSS OFF is shown, enter the set of Rx CTCSS/DCS FRQ 5 Set the Rx CTCSS/DCS value with the keypad, P4 to confirm. 6. Press P to delete, and press 7. * Stands for the radix point, press to convert among CTCSS DCS and reverse DCS. 1 Set Tx CTCSS/DCS 1 As shown: in CH 1 , press 2. Press P2 / P 3 , and Ch Edit Ch alias 3.
5. Press P4 to enter the wired clone, as shown Programming . (The two radios should be connected with each other by a clone cable.) Check the radio information 1. As shown: in CH 1 , press P4 to enter select mode, 2. Press P2 / P 3 , and Radio Infor is shown, 3. Press P4 to select, 4. Select Fre Range / MCU Version with P4 / P 3 , Fre Range indicates the radio frequency range; MCU Version indicates the radio version.
you can select any scan list. Every scan list can scan any channels in different zones (16 channels to the most). 3. Press it a third time Lone working Press the button set as lone working to start lone working. This mode is to ensure the safety of the user while using the transceiver separately. It can be set as: short press : lone working, long press OFF. 1. Press the programmable key once to start lone working; 2. Press once again to quit.
It can be set as: short press: Select squelch level, long press OFF. 1. Press the programmable key once, Level 2 will be shown, 2. Select squelch level with 3. Press P4 P2 / P3 , e.g.: Level 3 Level 4 Level 5 to confirm. Companding Enter the Companding mode when press the key programmed as Companding , It can be set as: short press: Companding, long press OFF. 1. Press the programmable key once to open the Companding mode, Zone P will be shown, CHANNEL 1 2.
1. Press the key once to make a call (within the current channel), and will quit automatically after the call. 2. Press it again to stop the alert. Back light Turn on/OFF the back light. It can be set as: short press: back light, long press 1. Press and hold on this key, the back light is on, 2. Release it to recover the normal mode. OFF. Adjust display contrast You can adjust the display contrast as per your need. It can be set as: short press: display contrast, long press 1.
Zone 0 2. Press it again to cancel channel lock, CHANNEL 1 will be shown. Set man down It can be set as: short press: man down, long press 1. Press the key once, man down will be shown, off. 2. Cancel the mode by pressing it again, VOX VOX function enables you to use the radio without manual operations. This function can only be set by the dealer, and you have to be equipped with the specified earphones. Before using VOX, you must set VOX gain level.
USER'S RESOLUTION Busy Channel Lockout (BCL) Busy Channel Lockout can prevent you from interfering other radios that using the same channel. Press the PTT button when the channel is busy, the radio with BCL function active will make warning sound and prohibit transmitting. To stop the warning sound, please release the PTT button and the radio returns to receiving mode.
content. If the PTT ID on the channel you select has been set with 5-Tone, 5-Tone signaling will be transmitted when making a call;or transmit 5-Tone signal by pressing the Call 1/2/3/4 button,, which can be set by the dealer. Transmit beginning/ending signaling (PTT ID) The identify signal of transmit beginning/ending are used to maintain or disconnect some repeaters or phone system. Transmit beginning is used to connect routine repeaters and aux-iliary facilities.
Major Specifications Status setting (by the dealer) Model Frequency Mhz PT6500 Model (1) 136~174 (2) 400~470 (3) 450~520 (5) 350~400 Modulation 16K F3E/11K F3E Number of Channels 128 Serial No. A) Channel setting Channel Receiving Transmitting CTCSS/DCS CTCSS/DCS Power frequency frequency No. decoding encoding Band width Scan -ning BCL 1 2 Channel Spacing 25 kHz/12.5kHz/20 kHz MF 1st MF 51.65MHz 2nd MF Working Voltage 7.
B) Optional function 2 1 Time-out timer TOT 15~600 s 2 2 Squelch level 1~9 2 3 Battery saving Off 1 1 1 2 Side button2 None Voice Reporting Selector Rptr/Talkaround 1 4 C) Auxiliary functions button setting: Call1/2/3/4 Lone Working Top button Side button1 Man Down None None Scanning Voice reporting selector Voice Reporting Selector High/low Power Shift Rptr/Talkaround Rptr/Talkaround Squelch Level Adjuster Call1/2/3/4 Call1/2/3/4 Monitoring Open/Cancel Lone Working Lone Working Squelch
DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY 1588 1313 34 We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, China We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.
