Version: V1.00.
FCC Requirement Changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC/IC RF Radiation Exposure and SAR Statements The device has been tested for body-worn Specific Absorption Rate (SAR) compliance. The FCC/IC has established detailed SAR requirements and has established that these requirements. RF Exposure Information The radio module has been evaluated under FCC Bulletin C95.1 and IEEE 1528 and found to be compliant to RF Exposure from radio frequency devices. This model meets the applicable government requirements for exposure to radio frequency waves.
Copyright Information Copyright © 2022 by SHENZHEN KINGBOLEN ELECTRONIC TECHNOLOGY.,LTD (hereinafter referred to as “KINGBOLEN”). All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying and recording or otherwise, without the prior written permission of KINGBOLEN. The information contained herein is designed only for the use of this unit.
Adapter information Avoid immersing the device in water or placing it in a location where it may absorb moisture or other liquids. During normal use, the charging device may become hot. Please ensure that there is good ventilation while charging device. If any of the following situation occurs, please unplug the charging device: • The charging device is exposed to rain, liquid or in an environment with excessive overlap. • The charging device showed physical damage. • Cleaning the charging device.
Content 1. Quick Start Manual.............................................................................................................1 1.1 Initial Use.............................................................................................................................................. 1 1.1.1 Turn on the Machine ................................................................................................................... 1 1.1.2 Language Setting.............................................
3.4.24 Seat Calibration....................................................................................................................... 25 3.4.25 Coolant Bleeding..................................................................................................................... 25 3.4.26 Tyre Reset............................................................................................................................... 25 3.4.27 Windows Calibration................................................
1. Quick Start Manual 1.1 Initial Use The following settings should be made when you initially use the device. 1.1.1 Turn on the Machine After pressing the power button, images will be shown on the screen as follows. 1.1.2 Language Setting Select the target language from the languages displayed on the interface. 1.1.3 Connect Wi-Fi The system will automatically search all available Wi-Fi networks. Please connect to the trusted Wi-Fi. ！ Tips: Wi-Fi must be set.
1.1.4 Choose Time Zone Choose the time zone of the current location, then the system will automatically cofigure the time. 1.1.5 User Agreement Please read all the terms and conditions of the user agreement carefully. Choose “Agree all the above terms”, and tap “Next” to complete the registration process. Then the page will jump to the “Congratulations on your successful registration” interface. 1.1.6 Create an Account You need to use your email account to register a KINGBOLEN personal account.
1.1.7 VCI Activation Enter the connector serial number and activation code to activate and bind the diagnostic connector. If you have not activated it, you can also tap "Settings" on the main interface to enter and select "Activate" to operate. ！ Tips: The activation code is an 8-digit number and is pasted on the "password letter". 1.
1.3 Function Menu After startup, the system will automatically enter the homepage: It mainly includes the following features: • • • • • • • • • The device and diagnostic connector support wired communication and Bluetooth communication. Support powerful intelligent VIN recognition technology, which is convenient, fast and efficient. Quick check: Automatic Identification of Vehicle Information, Auto Checking and Report Printing.
1.4 Charging Follow the steps below to charge the device: • Use the charger to connect the device and the power socket to charge. • When the battery status displays , the device is charging. When it displays , the charging process has been completed and you shall disconnect the device. 1.5 Battery • It is normal that the device cannot be turn on when charging because the battery has not been used for a long time or maybe the power is exhausted.
(3) For non-OBDII/EOBD vehicle, If the pin of the DLC is damaged or has insufficient power, please try any of the following methods to proceed: a. Cigarette Lighter Cable b. Battery Clamps Cable (4) Non-standard 16-PIN vehicle diagnostic sockets (OBDI). A.
About 1996, before the United States unified the OBD II standard and during the transition period, different automobile manufacturers had different diagnostic port for OBD I. Such as three PIN like HONDA; 17 PIN like Toyota; 38 PIN like BENZ.
OBD I Connector OBD I Transfer Cable OBD Connector Transfer process ！ Note: when using older models, the Transfer Cable must be used, with the small power connector on it, which is connected to the power connector of the power double clamp cable, this is a solution for certain cars before 1996, whose diagnostic holders do not have a 12V power supply.
1.8 Wireless TPMS / Battery Tester Installation (Bluetooth). Tap Wireless TPMS or Battery Tester, and you can detect the corresponding module in Bluetooth mode. You need to match the module by activating it. 2. Introduction 2.1 Product Profile (KINGBOLEN K10/K10 Plus) The device based on the Android 10 System, is a new generation of modular high-end intelligent diagnostic equipment developed by KINGBOLEN.
2.2 Components & Controls 4 1 3 2 8 5 7 6 No. Function 1 Display 2 Power Key： Hold the button for 3 seconds to turn the device on, or off, and 10 seconds for a forced restart. Press the button to wake up the device or turn off the device. 3 Type C Port: connect the supplied charger for charging. 4 USB Port: Reserved for add-on modules and other devices with similar port.
7 8 Megapixel Front Camera 8 Adjustable Kickstand: Able to keep the device standing on the desk, or hang the device on the steering whel with 180 degree rotation. 2 1 NO. Name Descriptions LED indicator is located at the bottom, and the three status as follows: 1 Indicator Light • Power: Green light indicates that the power is on. • Diagnosis: Blue light shows that it enter the diagnosis mode. • Vehicle: Flashing-blue light means it is communicating with the vehicle.
2.3 Parameters K10 K10 PLUS Operating System Android 10.0 Android 10.0 Memory 4G 4G Storage 64G 128G Battery 12600mAh\3.7V 12600mAh\3.7V Screen 10 inches 10 inches Camera Front Camera 8.0MP Rear Camera 8.0MP Front Camera 8.0MP Rear Camera 8.0MP Network Wi-Fi, WLAN 802.11b/g/n Wi-Fi, WLAN 802.11b/g/n Bluetooth Bluetooth 5.1 Bluetooth 5.
If the device failed to access the VIN information, please use “Diagnosis”. At this point, you need to manually input the VIN code to gain the car information. 3.2 Diagnosis In this mode, user can manually select vehicle models and systems for diagnosis. 3.2.1 Manual Diagnosis The device also supports step-by-step manual selection of menus for diagnosis. To use the "DEMO" as an example to introduce how to start the diagnosis as below. 1.
3.2.2 Smart Scan It enables you to quickly access all the electronic control units of the vehicle and generate a detailed report about vehicle health. (This function varies from vehicle to vehicle.)The system will start scanning Electronic Control Units to see if there are fault code and displays the specific results. Tap "Report" to generate a vehicle health report.
3.2.3 System Scan To check how many systems the car is equipped with. 3.2.4 Choose to Scan Choose the target automotive electronic control system to scan.
3.2.5 System and Function After “Smart Scan”, And then we can choose one system to check the detail information. Tap “PCM” as an example to demonstrate. The following page shows the selection interface. To check “System and Function”, tap “Enter” to get a corn interface, which is the functional interface of each electronic control unit. A. Version Information As shown in the picture, “Version Information” to read the current version information of the car ECU. B.
the cause of the vehicle breakdown.As shown below, “Read Fault Code”, and then the screen will display diagnostic results. ！ Tips: Reading the DTC when troubleshooting a vehicle is only a small step in the entire diagnostic process. Vehicle DTC are for reference only, and parts cannot be replace directly based on the given DTC definition. Each DTC has a set of test procedures.
On-screen Buttons: Display the parameters of the selected data stream in waveform. On the data stream waveform page, you can do the following: [Combine]: Display in graph merge status for data comparison. [Value]: Display the parameters in values and shown in list format. [Graph] [Customize]: Customize the data stream option to be viewed. Tap the button, a pulldown list of the data stream items appears on the screen.
Display the current (single) data stream in waveform graph. On the waveform graph page, you can do the following: [Min/Max]: To define the maximum/minimum value. Once the value goes beyond the specified value, the system will alarm. [ ] [Customize]: Tap “ ” on the right side of the screen, to define the data stream option to be viewed. ！ Note: Max 4 data streams can be displayed at the same time. [Compare Sample] 19 To select the sample DS file.
[Report] [Record] [Save Sample] To save the value of current data stream. To record diagnostic data, for you to replay and review. Tap “Stop” button to end reading. The saved file follows the naming rule: It begins with vehicle type, and then the product S/N and ends with record starting time. All diagnostic records can be replayed from User Info -> My Report. To sample data stream.
3.4 Maintenance The device supports matching, coding, programming of most vehicles’ programmable modules, and most commonly used maintenance and reset functions: Oil Reset; Elec.
value of the ECU returns to the initial state. By doing these, the movement of the throttle (or idle motor) can be more accurately controlled, thus adjust the intake volume. Situations when throttle matching is needed: a. After replacing the electronic control unit, the relevant characteristics of the throttle operation have not been stored in the electronic control unit. b. After the electric control unit is powered off, the memory of the electric control unit’s memory is lost. c.
a. The brake pad is replaced or brake pad wear sensor. b. The brake pad indicator lamp is on. c. The brake pad sensor circuit is short, which is recovered. d. The servo motor is replaced. 3.4.7 DPF Regeneration DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.
tire is replaced for the car with tire pressure monitoring function. 3.4.12 Suspension Matching This function can adjust the height of the body. When replacing the body height sensor in the air suspension system, or control module or when the vehicle level is incorrect, you need to perform this function to adjust the body height sensor for level calibration. 3.4.13 AFS Reset This feature is used to initialize the adaptive headlamp system.
time, the transport mode needs to be deactivated to restore the vehicle to normal. 3.4.20 A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 3.4.21 Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware). 3.4.22 NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust.
3.4.31 Engine Power Balance Monitoring At the power stroke of each cylinder, power balance monitors crankshaft acceleration, thus determining the relative power provided by each cylinder. 3.4.32 Gas Particulate Filter Regeneration After long-term use of the particle catcher, fuel consumption can be increased, engine output power can be decreased, then in this case, the GPF needs to be replaced or regenerated. 3.4.
C. Learning: to write the sensor ID into the vehicle ECU for sensor identification. 3.6 ADAS Advanced driver assistance systems (ADAS) is an electronic component in vehicles that include a variety of vehicle safety functions such as automatic emergency braking (AEB), lane departure warning (LDW), lane keeping assistance, blind spot elimination, night vision cameras, and self-adaptive lighting. For this function, it is necessary to use the ADAS calibration device produced and activate ADAS software.
3.7 Module The device supports optional function modules, list as below: S/N 1 2 3 4 Name Image Description Printer Thermal printer, can be used with the device or moduledock, quickly print diagnostic reports anytime and anywhere. Video Scope Ultra long custom coil pipeline design, flexible bending with durable materials, suitable for a variety of complex environments. Multiple uses with 3 kinds of special connectors (Hook, side view mirror, magnet). Supports 720P HD image.
ID number to the remote technician or after-sales personnel, you can authorize the other party to remotely operate the device, so as to guide you to the problems encountered in the process of using the device. 3.9 Store In the store, vehicle diagnostic and maintenance software can be bought. Each diagnostic software has a detailed function introduction. All hardware products can also be purchased online. 3.10 File It is used to record and establish the file of the diagnosed vehicles.
3.11 Repair Info Tap "Repair Info" on the homepage, the following page will appear. 3.11.1 OBD Fault Code Library You can enquire the definition of OBD fault codes. 3.11.2 Coverage List You can enter the Vehicle brand, model, year and other information to enquire the support functions and diagnostic system. 3.11.
Upgradeable software: A list of software that can be upgraded to newer versions. Upgraded software: A list of software that has been downloaded. ！ Note: During the upgrade, please keep normal network connection. Upgrade many software may take a few minutes, please wait. If you need to cancel certain software, please enter setting -> diagnostic software clear -> remove software to operate. Renewals: Please contact your local dealer to purchase a K-code card when your vehicle model package expires.
Tap OK to enter the vehicle diagnostic feedback selection screen. There are three options: Feedback: Tap to show the list of all tested vehicle models. Tap on the target diagnostic record, filling out some information and tap "Submit Result". After submission, our engineers will be able to analyze the data from the diagnostic report. History: Tap to view all diagnostic feedback reverted and the processing progress.
4.1 VCI If several VCI connectors are registered on the device, this option allows you to choose one from those. 4.2 Activate VCI This step allows you activate a new VCI connectors or get help. Input the Serial Number and Activation Code, and then tap “Activate” to activate it. Once the VCI connector is activated, the serial number of it will be displayed in the list which located in the VCI. 4.3 Activate TPMS VCI This step is for binding the Tire Pressure Monitoring System.
4.4 Fix VCI firmware/system Use to repair the VCI firmware. During the repair, please don’t power off or switch interfaces. 4.5 Data Stream Sample This feature allows you to manage the recorded data stream sample files. 4.6 My Order Use to manage order details. 4.7 Profile Use to set and manage personal information. 4.8 Change Password This item allows you to modify your login password. 4.9 Wi-Fi Set up Wi-Fi networks that can be connected. 4.
4.13 Diagnostic Record You can check the diagnostic history in here. 4.14 Photo Album This module saves the screenshots. 4.15 Screen Recorder This module saves the screen recordings. 4.16 Clear VCI Data Clearing VCI data will delete all download software, diagnostic records, and user setting, etc., which are associated with the VCI. 4.17 Settings In here, we would be able to check the version, system, storage and other fundamental settings of the device. 4.17.
4.17.5 Units It controls the data unit in the device. Choose the one that you are accustomed to reading. 4.17.6 Clear Cache To clear all the storage software, account, information, setting, and all the records of the device to save the space. PLEASE USE IT WITH CAUTION. 4.17.7 Mode Switch When connecting with other modules, HOST MODE must be used. 4.17.8 Restore Factory Settings Factory Reset, delete all data and restore the original settings. PLEASE USE IT WITH CAUTION. 4.
5.FAQ Q: Can I use the same type of charger to charge the tablet? A: No, please use original charger. Our company is not responsible for any damage and economic loss caused by using charger, which is not provided by KINGBOLEN. Q: How to save power? A: Please turn off the screen while the device isn’t used, set a shorter standby time, and decrease the brightness of the screen.
Q: Why can’t I log in? Possible reasons Solutions The device is not connected to the network. Please make sure the network is connected. The username or password is incorrect. Check the username and password. Contact KINGBOLEN after-sales service or regional sales to retrieve the user name and password. Server problem. Server maintenance, please try again later. Q: Why can't I activate the device? Possible reasons Solutions The device is not connected to the network.
Q: Why the software upgrade failed? Possible reasons Solutions The device is not connected to the network. Check the network connection. The username or password is wrong The device has not enough memory. Check the username and password. Uninstall irrelevant applications and delete uncommonly used vehicle software (enter setting -> diagnostic software clear -> remove software to operate). Server problem. Server maintenance, please try again later.
Q: What if the connector is lost? A: Contact KINGBOLEN after-sales service or regional sales. Q: What if the downloaded diagnostic software is inconsistent with the serial number? A: There are several connectors registered under the equipment account, and the serial number of right connector has not been selected.Enter the settings-[VCI] and select the right serial number of connector. Delete the problematic software, then enter the upgrade center to download the diagnostic software again.
Warranty Terms ▪ This warranty applies only to users and distributors who purchase KINGBOLEN products through normal procedures. ▪ Within one year from the date of delivery, KINGBOLEN warrants its electronic products for damages caused by defects in materials or workmanship. ▪ Damages to the equipment or components because of abuse, unauthorized modification, use for nondesigned purposes, operation in a manner not specified in the instructions, etc. are not covered by this warranty.
