IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT R EMOVE COVER (OR BACK). NO USER-SERVICEABLE PART S I NSIDE . R EFER SERVICING T O Q UALIFIED S ERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product`s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna. 1) Read these instructions. All the safety and operating instructions should be read before the product is operated. 2) Keep these instructions. The safety and operating instructions should be retained for future reference.
IMPORTANT SAFETY INSTRUCTIONS 17) Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18) Object and liquid entry Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product.
Location of Controls Top View 1 2 3 1. Turntable platter 2. Turntable center spindle 3. 45 RPM adapter 4. Lever 4 5 PH LINE IN ON INE IN BT O L 6 7 INDICATOR 6. LINE IN jack 7. Speed selector 8 9 8. Function knob 10 10.Power ON-OFF/ Volume knob ON OFF 5. Tone arm holder 9. Tone arm 11 12 11. Indicators 13 12. HEADPHONE jack HEADPHONE 13. Stylus Front View 15 14 14. Metallic buckle 15. Handle 16. Speakers 16 16 Rear View 17.
Location of Controls Inner Side View 20 20. Remote Sensor 21. Decorative LED lights 21 Remote Control: 2 LED ON/OFF LED1 LED2 3 4 5 LED3 LED4 LED5 6 7 8 RED GREEN BLUE 9 1 1. LED ON/OFF button 2. LED 1 button 3. LED 2 button 4. LED 3 button 5. LED 4 button 6. LED 5 button 7. RED button 8. GREEN button 9.
Remote Control FIRST TIME USE ● Remove and discard the insulation film as figure on the right. ● Replacing the button cell when it is drained: 1. Push and slide out the battery holder as figure 1 below. 2. Replace the button cell with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.3 BATTERY PRECAUTIONS Follow these precautions when using a battery in this device: 1. Use only the size and type of battery specified. 2.
Power Source 1. Connect one of the small plug from the supplied AC/DC Adapter to the DC IN jack of Decorative LED lights; connect the other small plug to the DC IN jack of the Main Unit as illustrated below. 2. Plug the AC/DC Adapter into a conveniently located AC outlet having AC 100-240V~, 50/60Hz.
Listening through Bluetooth (BT) Bluetooth Pairing: For first time use or re-pairing to a new BT Device, pairing it as below: 1. Power on the unit and turn the Function selector to BT position as the instructed earlier. The color of indicator will turn to Blue and blink. 2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. After paired, the Blue indicator will stop blinking.
Listening a Record 1. For first time use, take out the protective cover from the stylus as the illustrated below: Plastic protective cover (White color) 2. Place the Record on the center spindle. Note: If you are playing a 45 RPM Single (small size record), place the supplied 45 RPM adapter to the center spindle then place the record on it. 3. Slide the Speed selector to 33; 45 or 78 to match the play speed of the record. 4. Unlock the Tone Arm from the holder as the illustrated below: clip 5.
Other Connections LINE IN: LINE OUT: Listen music from the external Audio Player as follows: 1. Connect one end of the supplied Audio Connection Cable to the Phones Jack; Line Out Jack or AUX Out Jack on the external Audio Player. To listening from external Audio Amplifier: 1. Connect one end of the RCA Audio Connection Cable (not supplied) to the Line IN Jacks or AUX IN Jacks on the external Audio Amplifier. 2. Connect the other end to the LINE IN Jack on the top of unit as the illustrated below: 2.
Records Handling Do not touch the record's grooves. Only handle records, by the edges or the label. Make sure your hands are clean. Skin oils from even clean hands can leave a residue on the record surface that will gradually deteriorate the quality of your record. grooves label edge Keep your hands away from dust. Keep them in a cool, dry place. To avoid dust and scratches, keep records in their sleeves and jackets when not in use. Store records upright on their edges.
Troubleshooting Guide Symptom Possible Cause Solution Power AC/DC Adaptor had not connected to unit or wall outlet No power Power ON-OFF/Volume knob is on power off position Connected the AC/DC Adaptor to the unit an d wall outlet Turn the Power ON-OFF/Volume knob clockwise to power on the unit and set the volume to the desired level Turntable Noise or sound distorted Speed selector wrong setting The stylus may abrasion after long time used Set the Speed selector to the correct posit ion 33; 45 or
General Specifications 9V, 1300mA, Power Source: DC Audio Power: Impendence of Speakers: 1.8 W (RMS) x 2 4 Ohm; 3W x 2 BT Version: BT Effective Range: 32 feet in open area Turntable: Speed: Type of Stylus: 33; 45; 78 rpm selectable CSC-015 2.1 Accessories 1 x User’s Manual 1 x AC/DC Adaptor (Input: AC 100-240V~; 50/60 Hz; 0.5A; Output: DC 2 x Stylus (one pre-mounted) 9V, 1300mA, ) 1 x 45 RPM Adaptor 1 x Audio connect cable with 3.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
