Instruction Manual

If you get something wrong when program or entry PIN Code and
can not proceed with any operation, you could reset the keypad.
Remove the battery cover and you will see a Reset Button.
Press and hold the reset button for about 5s a beep sound to
confirm the keypad has been reset successfully.
Now the keypad has restore Factory Set model with PIN Code
1111# for 1st channel and 2222# for 2nd channel.
Factory Reset
RESET BUTTON
Battery
Replace the 9-Volt battery when keypad light
becomes dim or does not light up. Slide cover
up, remove battery cover, and replace battery.
Re-programming maybe necessary.
9V Battery
Operation instructions
Opener activits 4-digit password and “#” enter button is pressed. If wrong
numbers are accidentently pressed, correction can be made immediately.
The “#” Enter button will transmit only the last four digits.
The keypad will exit the programming mode if the keypad did not receive
any commands within 6s.
Factory default set Wireless Keypad with beep alarm and back indicator light.
When programming, if user key in users’ PIN Code more than 4 digits, the
keypad would recognize it as incorrect operation,then exit programming mode.
Keypad allows two attempts of wrong entire pin codes. After the third wrong
entire pin codes key-in, the keypad will be locked for 2 minutes with 3 beeps
and red LED light goes on. 2 minutes later, keypad would have one beep
sounds and red. LED indicator goes off to indicate the user keypad is unlock.
Installation
Select a location to mount the Keypad at a minimum height of 5 feet (1.5m)
out of the reach of Children.
1
Remove battery cover and battery.
2
Mark the top mounting hole and drill 1/8 inch(3.2mm) pilot hole.
3
Install the top screw, allowing 1/8 inch (3.2mm) to protrude above the surface.
Position the keypad over the top screw.
4
Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom
screw. Do not overtighten to avoid cracking the plastic housing.
5
Re-install battery and replace cover.
6
- Did the keypad lights come on when you entered your PIN ? If the keypad lights do not turn on when you press a button, it indicates that the battery needs to be
replaced. Replace with a 9V battery.
- The keypad should retain its memory.If the keypad no longer operates the operator.Reprogram the keypad to your system.
- Try reprogramming the keypad to the garage door opener.
- Make sure the keypad is compatible with your garage door opener.
Trouble Shooting
Q: Why won't my keypad work?
Q: Will I have to reprogram the keypad after changing the battery?
- Locate the Learn Button or DIP Switches on the garage door opener/receiver.Most garage openers have a built-in radio receiver or an external receiver.
Q: Where is my Learn Button or DIP Switches on my gate/garage?
- Yes. Our garage door keypad can support 2 garage door opener independently.
Q: Can I program the keypad to a second garage door opener?
- Remove the battery cover and you will see a Reset Button. Long press the Reset Button about 5s,you will heard a beer,now it has been resettled successfully .
Q: How can I reset the keypad when I forgot the entry PIN code ?
1 2 3
4 5 6
7 8 9
0 #
1 2 3
4 5 6
7 8 9
0 #
1
1 2 3
4 5 6
7 8 9
0 #
2
1111#
2222#
OR
_ _ _ _
1 2 3
4 5 6
7 8 9
0 #
new PIN Code
#
3
Change an Existing PIN Code
1. Press and hold the and button at the same time for enter into program model.
*
#
2. Enter a 4-digit factory set PIN Code 1111# OR 2222# of your choice.
NOTE: Factory set PIN code 1111# for 1st channel, 2222# for 2nd channel.
* The new PIN code you set MUST be remembered !
3. Enter a 4-digit new PIN Code _ _ _ _ end up with
# button for confirm.
To prevent possible SERIOUS INJURY from a moving garage door :
• Install Keypad within sight of garage door,out of reach of children at a minimum
height of 1.5m above floors, landings,steps or any other adjacent walking
surface,and away from ALL moving parts of door.
• NEVER permit children to operate or play with Keypad.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted,
and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
• If battery is swallowed, immediately notify doctor.
Thank you for purchasing our products
Our products are covered 1 year limited warranty from the date of its original
purchase. If any problems occur, please contact us for help.
One Year Limited Warranty.
WARRANTY