User Manual Badge Camera T0 Shenzhen Jingyi Smart Technology Co., Ltd https://en.pwithe.
Safety Instruction These instructions are intended to ensure that user can use our product correctly to avoid danger or property loss. Cautions: Injury or equipment damage may occur if any of cautions are neglected. ●In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. ●Input voltage should meet both the Safety Low Voltage and the Limited Power Source with 5V DC. ●Please make sure that the plug is firmly connected to the power socket.
1 Overview Button and Indicator Button Power/Video Operation Description Press and hold for three Power on/off seconds Indicator LED Indicator -2- Indicator status Solid red Description Charging
Press Press and hold for three seconds Press and hold Wifi/Important for fifteen Tag Button seconds Press Start/Stop video recording Red light off Fully charged Turn on/off Wifi Solid green Standby Soft reset, restore factory settings Blinking in green Video recording Mark video with important tag Fast blinking blue Wifi turned on, waiting to be connected Blinking in blue Wifi connected Wifi Indicator Reset Button Press Power off Prompt Tone Start video recording Beep Stop video recordin
Synthetic Stickers (mm) Style B: Laser Engraving Style A: Synthetic Stickers 3 Operation Power on/off In the shutdown mode, hold the Power/Video Button for 3 seconds, when you hear a beep, it means the Badge Camera is turned on and enter into standby mode, the green indicator is always on. In the standby mode, hold the Power/Video Button for 3 seconds, when you hear two beeps, it means the Badge Camera is turned off and all data are saved, the green indicator goes out at the same time.
mode, all videos are saved at the same time. The indicator stops blinking and turns into solid green. Important Tag During the video recording process, press the Wifi/Important Tag Button, when you hear three beeps, it means the current video is marked as important. When viewing the local files, the video will be embedded with an "important" watermark. Reset In the standby mode, if the system crashes, or the operation fails to respond, press the reset button with a Sim-ejector to force shutdown.
in the file system column. Download and Installation of PeVision Turn on mobile phones, tablets, or other Android devices, scan the following QR code, or scan the QR code on the back of the Badge Camera, download and install the PeVision App according to the prompts. Wifi Steps a. Open the PeVision App, turn on the Badge Camera at the same time, hold the Wifi/Important Tag Button for 3 seconds, when the Wifi indicator starts blinking in blue quickly, it means the device is ready for connection. b.
Badge Camera Settings When the Badge Camera is connected to the APP, you can select and enter the setting interface (as shown in the figure below) for custom settings. The user can set the device information such as video resolution, duration, loop recording, user name, user ID, department ID, as well as department name, and set AP Wi-Fi name, Wi-Fi password and other information.
APP Operations When the Badge Camera is connected to the APP, it can be used for video recording, remote recording, screenshot, settings, file management and other operations through buttons on the APP interface. Among them, in the preview interface, you can click the button in the lower left corner of the player to turn on the sound playback, the audio and video are played synchronously. It is recommended to listen to the audio information through the headset.
Reset If you forget the set Wi-Fi password, you can hold the Wi-Fi/Important Tag Button of the device for 15 seconds to perform a soft reset. The Badge Camera will replace the Wi-Fi password, user information and other parameters, and restore it to the factory settings.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SAR: The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact is minimized during normal operation. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/Kg.
