User's Manual

Wireless
smart otoscope
Professional Otoscope
User Manual
Quick start guide
1. Scan QR Code to download app.
2. Remove the lid and the otoscope will
be power on automatically.
3. Install the earpick firmly on the
otoscope tip when you need to pick your
ear.
4. Connect product WiFi:weiview-xxx.
5. Return to the App then click
“start” to inspect ear.
6. The inside of the ear can be observed
in real time by the App.And the
transparent earpick won’t block your
view.
7.Screen lock is designed to
avoid misoperation of children.
8. Low battery alert.
When the battery is low, the red
light flashes,please charge in time
Product size
Product parameters
Product name: Professional Otoscope
Product Model: Wireless Smart Otoscope
Image transfer rate: 25fps
Image transmitter: CMOS
Operating ambient temperature: 10~50°C
Battery type: Lithium battery
Battery life: approx 1
hour Charging time: 1 hour
Input current: DC 5V 300ma
Probe diameter: 3.9mm
Optimnm focal length: 1.5-2cm
Gravity sensor: 3 Axis Gyro
Fault analysis and troubleshooting
Notes
1. Please observe the surroundings before use , and don't use the
product while running to avoid impact.
2. Before use , be sure to install a protective pear-picking rod and
fasten the head of the ear-picking rod to protect your ears.
3. This product is not suitable for children under 6 years old.
4. It is prohibited for children to use this product alone to avoid
careless harm.
5. Please store the product in the normal temperature and avoid
direct sunlight to avoid product damage.
6. The APP can not compatible with Samsung S7.
7. When cleaning the lens , please wipe carefully with the
professional alcohol cotton swab provided
8. In order to ensure the best use experience, please keep the child
in a seated position and operate the product horizontally when
picking the ear for the child .
9. FCC statement: This device complies with Part 15 of the FCC
rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interface;
2) This device must accept any interference received,
including interference that may cause undesired operation.
10. ROHS compliance: This product is in compliance with Directive
2011/65/EU of the European Parliament and of the Council of 8 June
2011 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
FCC WARNING:
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV
technician for help.
* RF warning for Portable device:
The device has been evaluated to meet general RF
exposure requirement. The device can be used in
portable exposure condition without restriction.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
Faults
Solution
No response on startup.
Try the correct boot method a few more
time.
Please charge with a matching charging
cable for 1hour,
Camera doesn't light.
Shutdown and restart the otoscope.
App crashing.
Uninstall the existing APP and rescan
the QR code for installation.
Power indicator light
flashes.
There is not enough electricity.please
use
the the matching charging cable for
charging,
and the charging time is 1 hour.
The product failed to
properly display real-
time images after
successfully
connecting to APP.
Disconnect the phone from the otoscope
WiFi, restart the otoscope, and
reconnect the WiFi.
The WiFi connection is
unstable and sometimes
disconnected in seconds.
Restart the otoscope and reconnect the
App
If the above operation fails to solve the problem, please contact
customer service, we will further provide you with a practical
solution,