User's Manual

ManualsBrandsSHENZHEN IP-COM NETWORKS ManualsComputers & AccessoriesWireless Access Point

Table Of Contents

页 1

Install Guide

Wireless Access Point

Model: AP255_US

Please read this Install Guide carefully before you start.

For information that is not covered here, see the User

Guide at http://www.ip-com.com.cn

Package Contents

* If any item is incorrect, missing, or damaged, please keep the original package and contact

your reseller for immediate replacement.

Get to Know Your AP

① Detach the AP’s cover plate using a screw-driver as shown in the figure.

System Requirement

Windows XP/7/8 or Linux

Web Browser : IE8 or higher or Google Chrome

Step 1: Configure the Computer(Take Windows 7 as an example)

① On the computer that connected to the Wireless Access Point, right click the icon

or on the bottom right corner of your desktop, and then click Open Network and

Sharing Center.

An electrical wall box should be pre-installed with an Ethernet cable running from the box.

② Connect the Ethernet cable from the wall box to a PoE switch, and connect the other

end of the Ethernet cable to the LAN port on the back panel of the AP.

③ Install the AP in the wall box. Verify that the Ethernet cable is positioned properly.

④ Fasten the AP with the included screws. Adjust the screws to ensure the AP is flush with the

wall for proper fitting of the cover plate.

⑤ Attach the cover plate to the AP.

② Click Local Area Connection > Properties

Install Your AP

Manage Your AP

Network Topology

Note:

All settings will be restored to factory defaults once you reset the device. You will need to

reconfigure the device for specific purposers.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case

the user may be required to take adequate measures.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a

shielded RJ45 cable.

Declaration of Conformity

Hereby, IP-COM Networks Co., Ltd. declares that the radio equipment type AP255_US is in compliance with

Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

http://www.ip-com.com.cn/en/ce.html

Operate Frequency：2412-2472 MHz EIRP Power(Max.)：19.8 dBm Software Version：v1.0.0.4

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

Step 2: Configure the Wireless Access Point

① Launch a web browser, type 192.168.0.254 in the address bar, and tap Enter on the

keyboard. Type the login Username and Password (Both are “admin” by default) and click

② Quick Setup: Click Quick Setup, select a mode according to your needs (Here take AP

Mode as an example); customize the SSID (wireless network name), select a security

mode/Cipher Type, customize the Security Key, and click Save.

③ LAN Setup: Click Network > LAN Setup, select a Address Mode, and complete the

releated settings.

Tip

If your computer is set to a static or fixed IP address (such as Step 1: Configure the

Computer), remember to set it back to Obtain an IP address automatically and Obtain

DNS ser ver address automatically after configuration.

③ Double click Internet Protocol Version 4 (TCP/IPv4) ④ Select Use the following IP address, and set up the computer ’s IP address to 192.168.0.X

(X indicates a number between 2 and 253), Subnet mask to 255.255.255.0, and then click OK

to save the settings.

Q1: I cannot access the device’s web UI by using the login IP address 192.168.0.254.

What should I do?

A1: ① Ensure that your computer is connected to the device properly, and the

device is powered on.

② Ensure that your computer ’s IP address is set to 192.168.0.X (X is a number

between 2 and 253).

③ Clear cache of the browser, or launch another web browser.

④ Try configuring the device on a different computer.

⑤ Restore the device to factory defaults (refer to the following question) and retry.

Q2: How to restore the device to factory defaults?

A2: Detach the device’s cover plate, press the RST button with a needle for over 7

seconds until the LED indicator turns to be solid to restore the device to factory

defaults.

FAQs

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the par ty responsible for compliance

could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications

to this equipment.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also

complies with Part 15 of the FCC RF Rules.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a

shielded RJ45 cable.

This documentation (including pictures, images, and product specifications, etc.) is for reference only.

To improve internal design, operational function, and/or reliability, IP-COM reserves the right to make changes to the products

described in this document without obligation to notify any person or organization of such revisions or changes.

Manufacturer: SHENZHEN IP-COM NETWORKS CO.,LTD.

Address: Room 101, Unit A, First Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District,

Shenzhen, China. 518052

Email: info@ip-com.com.cn

Website: http://www.ip-com.com.cn

Install Guide

Wireless Access Point

Model: AP255_US

Please read this Install Guide carefully before you start.

For information that is not covered here, see the User

Guide at http://www.ip-com.com.cn

Wireless Access Point 1 Ethernet Cable

Four pairs of screws

Install Guide

Wireless Access Point PoE Switch

Router

Internet

2:30 P M

6/16 / 2016

AP255_US

English

Username:

Password:

www.ip-com.com.cn

Quick Setup

AP Mode WDS Mode APClient Mode

IP-COM_888888

Mixed WPA/WPA2 – PSK

AES TKIP TKIP&AES

12345678

Mode

SSID

Security Mode

Cipher Type

Security Key

Save

Restore

Help

Status

Quick Setup

Network

Wireless

SNMP

Deployment

Tools

www.ip-com.com.cn

LAN Setup

00:90:4C:88:88:88

Static IP

192.168.0.254 For example: 192.168.1.1

255.255.255.0 For example: 255.255.255.0

192.168.0.1

AP255_US

Auto-negotiation 10M half-duplex

MAC Address

Address Mode

IP Address

Subnet Mask

Gateway

Primar y DNS Server

Secondary DNS

Server (optional)

Device Name

Ethernet Mode

Save

Restore

Help

Status

Quick Setup

Network

LAN Setup

DHCP Ser ver

Wireless

SNMP

Deployment

Tools

Interfaces

PoE Out + Data: 100Mbps LAN Port. Connect it to a

computer, etc. Only support PoE af class 2 or lower power

consumption device.

PoE In + Data: 100Mbps PoE/LAN Port (Supported PoE

power supply). Connect this port to a PoE switch.

Button

RST: Press it for over 7 seconds until the LED indicator

turns to be solid to restore the device to factory defaults.

LED

Blinking: The AP works properly.

Off: The AP is not powered on, malfunctions occur or LED

is disabled manually.

x 2

Detach the cover plate

Cover Plate

= +

RST

LED

RST

PoE Out + Data PoE In + Data