THANK YOU! We are grateful for your purchase of HYT product. We believe this easy–to-use radio will provide you with clear and reliable communications at peak efficiency. This HYT portable two-way radio is a precision device. Treat it with care, and you will enjoy years of reliable operation.
Contents User Safety, Training, and General Information Compliance with RF Energy Exposure Standards FCC Compliance Precautions Product Inspection Battery Information Accessory Installation Radio Overview Features and Operation Basic Operations Time-Out-Timer (TOT) Battery Save Low Battery Alert Monitor Programmable Function Key High/Low Power Compatible Channel Bandwidth 2-Tone Encode & Decode DTMF ANI CTCSS/DCS Signalling Signalling AND/OR Logic Channel Scan Busy Channel Lockout Troubleshooting Guide Car
User Safety, Training, and General Information READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE USING YOUR HYT PORTABLE TWO-WAY RADIO. Compliance with RF Energy Exposure Standards Your HYT two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy.
Antennas & Batteries Use only HYT approved, supplied antenna or HYT approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may violate FCC regulations. Use only HYT approved, supplied batteries or HYT approved replacement batteries. Use of non- HYT -approved batteries may exceed FCC RF exposure guidelines.
THANK YOU! We are grateful for your purchase of HYT product. We believe this easy–to-use radio will provide you with clear and reliable communications at peak efficiency. This HYT portable two-way radio is a precision device. Treat it with care, and you will enjoy years of reliable operation.
Precautions • • Only qualified technicians are allowed to maintain this product. Do not use the radio or charge a battery in explosive areas such as coal gas, dust, steam, etc. • • • Switch OFF the radio while refueling or parking at gas station. Do not modify or adjust this radio without permission. Do not expose the radio to direct sunlight over a long time, nor place it close to heating source. • Do not place the radio in excessively dusty, humid areas, nor on unstable surfaces.
Product Inspection Please carefully unpack the radio. Before use, it is recommended that you inspect the product as follows. First check the shipping carton for any signs of damage. Confirm the supplied product against the packing slip to assure accuracy. If any items are missing or have been damaged during shipment, please contact your dealer immediately. Supplied Accessories *Note: Item Qty.
Battery Information Battery Charging Information The battery is not charged at the factory. Batteries must be fully charged before initial use or if they have not been used for some period of time. The battery capacity will be optimum only after being charged / discharged for two or three times. When the battery power is low, it either needs to be charged or replaced with a new one. Notices: ★ Do not short the battery terminals or dispose of the battery by fire.
Accessory Installation Attaching the Battery 1. Turn off the radio. 2. Insert the tabs at the bottom of the battery into the slots at the bottom of the radio chassis. 3. Press the top of the battery towards the radio until a “click” is heard. (See Figure 1) ② ① (Fig. 1) Removing the Battery 1. Turn off the radio. 2. Push the battery latch on the back panel towards the top of the radio. 3. Pull the top of the battery away from the radio chassis, and lift the battery from the radio.
① ② ③ (Fig. 2) Attaching the Antenna 1. Align the threaded end of the antenna with the radio’s antenna connector. 2. Turn the antenna clockwise to tighten. (See Figure 3) Removing the Antenna 1.Turn the antenna counterclockwise until you can remove it. (See Figure 3) Attach 安装 Remove 拆卸 (Fig. 3) Attaching the Belt Clip 1. Align the grooves of the belt clip with those of the battery. 2. Press the belt clip downwards until the belt clip tab locks.
① (Fig. 4) Removing the Belt Clip 1. Press the belt clip tab upwards until it releases. 2. Slide the belt clip upwards to remove it. (See Figure 5) Note: remove the battery pack prior to removing the belt clip. ② ③ ① (Fig. 5) Attaching External Earphone (Optional) 1. Remove the cover of earphone jack. 2. Rotate the cover until earphone jack comes into view. 3. Insert the earphone plug into the jack.
Radio Overview (1) Antenna Used to transmit/receive signals.
The radio LED glows red during transmission and green during reception; The LED flashes red when battery voltage is low. (3) Channel Selector Knob (4) Power/Volume Control Knob Rotate the knob clockwise until a “click” is heard to turn the radio on, fully counter clockwise until a “click” is heard to turn the radio off. When the radio is on, turn the knob to adjust volume. (5) PTT Key Hold down the [PTT] key to transmit, release it to receive.
Features and Operation Basic Operations 1. Turn on the radio: Turn the Power/Volume Control Knob clockwise until a “click” is heard. 2. Adjust the volume: Turn the Power/Volume Control Knob to adjust the volume. When function key is programmed with monitor feature, turn the knob while holding down the function key to adjust the volume to a comfortable level. 3. Select a Channel: Rotate Channel Selector knob to select your desired channel. 4.
The Time-Out-Timer (TOT) is used to prevent someone from using the same channel for a long time and to prevent the radio from damage due to continuous transmission. If the transmission exceeds the preset time (it’s set by your dealer), transmission will be inhibited and a beep tone will sound. To stop the beep tone, release the [PTT] key. Press the [PTT] key again to resume transmitting.
Monitor This feature is enabled/disabled by your dealer. In receive mode, press the preprogrammed MONI key to monitor activities on the current channel. This operation is especially useful for adjusting volume level or receiving a weak signal. The LED indicator glows green in monitor mode. Programmable Function Key This key can be programmed as a shortcut to Monitor or High/Low Power feature, or set inactive through the programming software.
DTMF ANI This feature is enabled/disabled by your dealer. DTMF ANI is encoded by PTT ID. Each radio is assigned with one ANI code consisting of BOT ID (Beginning of Transmission) and EOT ID (End of Transmission). Each channel can be programmed by PC programming software to transmit/not transmit ANI code in transmit mode. CTCSS/DCS Signalling CTCSS/DCS may have been programmed on a channel to ignore unwanted calls from other parties on the same channel.
priority channel periodically while stopping on a non-priority channel. When there is any activity on the priority channel, the radio will automatically switch to the priority channel for communications. ■ Scan Revert Channel If the radio is scanning and you press the [PTT] key, it will transmit on the preprogrammed revert channel. The revert channel can be programmed by your dealer.
Care and Cleaning ◇ Do not carry your radio by the antenna or remote microphone; ◇ Wipe the battery contacts with a lint-free cloth to remove dirt, grease, or other material that may prevent good electrical connection; ◇ When not in use, keep the accessory jacks covered with the protective caps; ◇ Clean the shell, controls and keys of your radio with neutral detergent and warm water after a long period of usage. Avoid using strong chemicals.
Earholder Style Ear Microphone EH-M3 Switching Power Supply Remote Speaker Microphone SM-06M01 Frequency Chart Model: Serial Number: Channel Transmit Transmit Receive Receive Frequency CTCSS/DCS Frequency CTCSS/DCS 1 2 3 4 5 6 7 8 9 10 11 12 13 20
14 15 16 HYT endeavors to achieve the accuracy and completeness of this manual. All the above specifications and design are subject to change by HYT without notice. All the reproduction and translation of this manual without authorization of HYT is not allowed.
