® 14+ PLEASE READ THE INSTRUCTION MANUAL CAREFULLY BEFORE USE Q4 FPV NO: H111D
INDEX IMPORTANT SAFETY NOTES 04 7. START TO FLY 10 SYMBOL EXPLANATION 02 7.1Normal mode / Expert Mode 10 USAGE ADVICE 02 7.2 Headless mode 11 03 7.3 Aerial Flip 11 LIPO BATTERY SAFETY NOTES 8. TRANSMITTER 13 INDEX 04 INTRODUCTION 05 8.1 input key function 14 1 ITEMS INCLUDED IN THE BOX 05 8.2 Install the TX Battery 15 2 QUAD COPTER 06 8.3 Video REPLAY setup 15 3 MOTOR LED INDICATOR 06 8.4 TIME setup 16 06 8.5 FORMAT SD Card SETUP 16 06 8.
Please read the instruction manual carefully! IMPORTANT SAFETY NOTES OPERATION: Be extremely careful and responsible when using the drone. Small electronic components can be damaged by crashing or by dropping the X4 into water. To avoid further damages, please replace broken parts immediately. Flight: Take responsiblity for the safety of yourself and others when flying the X4! Do not fly the X4 in crowded places. Do not fly in bad weather. Never try to catch the X4 while it is in flight.
INTRODUCTION Thank you for buying HUBSAN products. The X4 quadcopter is designed as an easy-to-use, full-featured RC model capable of hovering and acrobatic flight maneuvers. Please read the manual carefully and follow all the instructions. Be sure to keep the manual for future reference. 1 ITEMS INCLUDED IN THE BOX Check all the items in the box before using.
2 QUADCOPTER [1] [2] [3] [4] [1] Propellers [2] Charging Plug [3] Motor [4] Camera 3. MOTOR LED INDICATOR Indicator Status: Front LED: is blue; Back LED: is red Power on: 1) Before binding, 2 front LED indicators blink alternately 2) After binding, 4 LED indicators remain lighted Headless Flight: 2 front LED blink slowly, 2 back LED remain lighted Video: 2 front LED remain lighted, 2 back LED blink alternately Low Power: 2 front LED remain lighted, 2 back LED blink quickly 4 QUAD COPTER BATTERY 4.
4.2 CHARGING Connect the battery to the USB charger, then connect the USB charger to USB devices, such as a computer or mobile power charger. It takes around 30 minutes to fully charge the battery. The USB LED indicator is in red when charging and will light off when the battery is fully charged. Please unplug the charger and battery when the charging is completed. Please fully charge the batteries to avoid loss of control due to low voltage. Risk of explosion if battery is replaced by an incorrect type.
Disassemble the propellers with U wrench. ● Make sure that the A and B propellers are installed correctly. The X4 will not fly if propellers are improperly installed. ● Hazardous moving parts keep fingers and other body part away. 6. START TO FLY 6.1 FLIGHT ENVIRONMENT (1) The flying area should be open and without tall buildings or other obstacles; the steel structure within buildings interferes with the compass and the GPS signal.
6.3 BASIC FLIGHT The operation mode for the transmitter including Mode 1 or Mode 2. The manual will use Mode 2 as an example to illustrate the transmitter’s operation. Transmitter (Model 2) X4 UP Remarks The throttle stick controls the ascent and descent . Push up the stick and the X4 will ascend. Pull down the stick and the X4 will descend. When the stick is in the center, the X4 will hover and hold its alititude automatically .
The Aileron stick controls left and right flight. Push the stick to the left and the X4 will fly to the left. Push the stick to the right and the X4 will fly to the right. Left Right The X4 will keep the current status when the stick is in the center. The angle of stick movement corresponds to the angle of tilt and flight speed. 6.4 VIDEO Insert the SD card into quadcopter before using Video function. Press the PVideo button for 0.5 second to take videos and press again to save the videos.
7.2 HEADLESS MODE Headless mode means the X4 will default any direction (corresponding to the directions of transmitter sticks) as its up head when the mode is activated. MODE 1 MODE 2 Press the Throttle stick 0.5 second to switch on/ off headless mode. Press the stick to enter into the headless Mode, indicated by one "beep" and the front LED will blink slowly . Press the stick again to exit headless Mode, indicated by one "beep". 7.3 AERIAL FLIP Press and hold down the Throttle stick for 1.
7.3.2 Right Flip Push the Aileron stick to the right. Release the stick to the center after the flip. MODE 2 MODE 1 7.3.3 Forward Flip Pull the Elevator stick forward. Release the stick to the center after the flip. MODE 2 MODE 1 7.3.4 Backward Flip Push the Elevator stick backward. Release the stick to the center after the flip.
8.
8.1 INPUT KEY FUNCTION S/N Mode/ Control (1) MODE 1 (2) 1 2 14 Throttle/Aileron Stick MODE 1 Elevator/Rudder Stick MODE 2 Throttle/ Rudder Stick MODE 2 Elevator /Aileron Stick Function Push the stick forward or backward and the quadcopter will ascend or decend; Push the stick left or right and the quadcopter will fly left or right.
8.2 INSTALL THE TX BATTERY PUSH Remove the cover PUSH Install 4 x AA batteries according to the correct polarities Close the cover ● Do not mix old and new batteries ● Do not mix different types of batteries ● Do not charge non-rechargeable battery. Notice： 1. When the power on the transmitter runs low, the red LED will blink quickly and the LCD screen will turn black, also the transmitter and X4 may disconnect. Please replace with new batteries. 2.
0:08:49 0:08:49 MAIN MENU PLAY RECORD PREV NEXT Play Record Set Real Time Format SD Card Set Reverse Set Sensitive 5.8G Frequence Exit Stop and Exit 001.avi 00:01 002.avi 00:00 8.4 TIME SETUP Pull the throttle stick to the lowest position and long press the Pitch stick simultaneously to enter into MAIN MENU interface. Push the Elevator stick up/down to select “Set Real Time”. Select “Exit” to exit.
8.6 REVERSING CHANNEL SETUP If you would like to reverse any of the stick functions due to personal preference then follow the instructions below. Be aware that it will change the controls back to front. Pull the throttle stick to the lowest position and long press the Pitch stick simultaneously to enter into MAIN MENU interface. Push the Elevator stick up/down to select “Set Reverse”. Select “Exit” to exit.
8.8 FREQUENCY SELECTABLE 5.8GHZ The transmitter will automatically find the best frequency to ensure a live video with good quality of transmission. Please re-select the frequency from 5730MHZ to 5845MHZ to get a better video transmission when necessary. Pull the throttle stick to the lowest position and press the Elevator stick for 1.5 second to enter into the MAIN MENU interface. Push the Elevator stick up/down to select “5.8G Frequency”, push the stick to the right to enter into the “ 5.
EXPLODED VIEW 2 1 3 4 5 6 7 8 9 11 10 11 12 NO PART NAME 01 02 03 04 05 06 07 Propeller A Propeller B Propeller A Propeller B Motor A Motor B Upper Body Shell QTY NO PART NAME QTY 2 2 2 2 2 2 1 08 09 10 11 12 13 Li-Po Battery 1 1 4 1 1 2 PCBA Motor Holder Camera Module Lower Body Shell Screw 19 ©2015 Hubsan 哈博森科技 版权所有
H111D SPARE PART CHART Body Shell Set H111D-01 H111C-02 H111D-02 H111C-04 Motor Holders Propeller Set Motor Set H111C-05 H111D-04 H111C-07 Lipo Battery 2.4G & 5.
FCC INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
