ha 0 {bassoonist Boost Your Bars User Manual 1 Commercial 30K Pro Prop-5S-LCD Mobile Signal Booster
= boost CONTENT WHAT'S INCLUDED HOW IT WORKS HOW TO INSTALL YOUR SIGNAL BOOSTER 1.1 Overview SITE 1.2 Installation prepare 1.3 How to find the location with the strongest received signal 1.4 Install Outdoor Antenna 1.5 Install Indoor Antenna 1.6 Install Signal Booster 1.7 Run coaxial cable 1.
WHAT IS INCLUDED ®» v = Commercial 30K Pro ACID Oar Supply Booster Mount Hardware We provide all casseroles needed for the signal booster. For moral Information please visit wwwhiboostusa.com. Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by new FCC rules. Please contact FCC for details: 1-888-CALL FCC.
© Commercial 30K Pro Signal Booster © Outdoor Antenna © Indoor Antenna © Cable © 12V/3A, AC/DC Power Supply 1.2 Installation Preparation Before you install = Make sure you have sufficient cable length between the proposed outdoor/indoor antenna location and booster connector. = Make sure the position you install the booster is near to an existing electrical outlet, well ventilated, and away from excessive heat, moisture, and direct sunlight.
signal from the local cellular towers. 3. Install the indoor antennas where you want to improve the signal level. 4. Mount the booster, connect the cables from the outdoor antenna and indoor antenna at the designated ports, and connect the booster to the AC supply (make sure all the cables are connected before applying power). 1.3 How to find the location with the strongest received signal The outdoor signal strength the booster receives directly affects the efficiency of the indoor coverage.
= boost gain and power, and there are not any alarms {no ISO, ALC, OFF legend flashing and no quick flashing green or red in Leeds, it means the present location is the best for ensuring that the booster has maximized performance. The maximum down link power for Commercial 30K Pro is DBMS, and the maximum down link gain is 63-72dB. Note: These showed values may vary dynamically at times between 1-3 dB which is normal due to outdoor signal conditions.
1to inch diameter pole © 1to 2 Inch diameter pole i Outdoor wadi band panel antenna installation for reference Note: Be sure the cradle is at the desired height and rotated toward the strongest cellular signal before tightening the nuts. Do not over tighten. 1.5 Install Indoor Antenna Select a place on a wall in the area where you need better reception. Mount the Indoor antenna with the included screws as shown in the figure below.
Tet Indoor wide band panel antenna Installation for reference La Indoor wide band dome antenna installation for reference 1.6 Install your signal booster The signal booster should be mounted in an easily accessible area so it’s easy to perform general maintenance. The optimal area would be on a wall located near a power outlet.
1.7 Run coaxial cable Loosely run the supplied coaxial cable from your outdoor antenna to your booster connector marked “Outdoor”. We recommend applying waterproof tape to fully waterproof the connection. Connect the indoor antenna cables from your Indoor antenna to the booster connector marked “Indoor”. Tighten the connection by hand. (After you have tested the system you can permanently secure the coaxial cable).
= boost fully reread and understand the LCD, LED indications, control buttons and MGC function on your booster, as they will help you identify and solve any potential issues. + LCD Features Working Up link Down link Down link Frequency Gain Gain Output i Power power from tower status Indicator Indicates DC power status Antenna Isolation Status Indicator Band Shut OFf Indicator Automatic Level Control (ALC) Activity Indicator Band: Shows the working frequency bands where the booster is operating.
OFF: In some rare situations the ALC or ISO will not be able to compensate for an oscillation condition or a down link overload, When this happens the booster will shut off in the affected band and the LCD “OFF” indicator will flash. Pressing the “SET” button will display which band or bands are affected.
= boost Control Buttons Operation When the LCD is in the fixed display mode, press the “SET” key for more than 3 seconds and it will start up in the Gain Setting Mode. Press the “SET” key for more than 3 seconds, and the LCD will return to the fixed display made. {For more details refer to Manual Gain Control (MGC) below. When the LCD is in the alarm display mode, press the “SET” key and the LCD screen will display the lama indication showing the affected band.
TROUBLESHOOTING Eliminate Flashing ISO legend and Quick Flashing Green, Quick Flashing Red ISO LED problems: 1. Adjust the outdoor antenna direction, keeping it away from indoor antenna. Restart booster. 2. Increase the vertical or horizontal distance between the outdoor antenna and indoor antenna. Restart booster. 3. Use barriers such as walls to increase the isolation. 4, Change the indoor antenna type to an antenna with a more directional antenna pattern.
= boost following: » Check to see If the Indoor antenna is installed correctly. Try moving the antenna to improve coverage. * Try adj AUTHORIZED KITTING OPTIONS g the direction the indoor antenna is pointing. The following accessories are authorized by the FCC to be used with the Commercial 30K Pro Signal Booster. Outdoor Antenna & Cable Kit Options Kit numbers: 11100400 Kat numbarc10.
= boost FCC RF EXPOSURE STATEMENT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instruction for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 1C RF EXPOSURE STATEMENT The device is compliance with RF exposure limits.
instructions, may cause harmful interference to radii communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by muting the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: + Reorient of relocate the receiving antenna.
PRODUCT WARRANTY 30-Day Money-Back: All Hi Boost products are protected by a 30-day money back guarantee. If for any reason the performance of any product is not acceptable, the product may be returned to the reseller with a dated proof of purchase. 3 Year Warranty Hi Boost Signal Boosters and kits are warranted for 3 years.
