H8951 3G SOHO Router User Manual Shenzhen Hongdian Technologies Corporation F5~6, Building 14, Shangsha Science & Tech Park, Binhe Blvd., Shenzhen, China Tel: +86-755-88864288 Fax: +86-755-83404677 Postal Code: 518048 www.hongdian.com www.mdtu.com Copyright 1997-2008 M80-892001-01 Release 1.0.
H8951 3G SOHO Router User Manual Declaration Manual Declaration Copyright All information in this user manual is protected by copyright law. Whereby, no organization or individual shall copy or reproduce the whole or part of this user manual by any means without written authorization from Shenzhen Hongdian Technologies Corporation. Trademark , , Hongdian, GPRS DTU, MDTU, Hongdian Technologies, Shenzhen Hongdian and Galaxy are the trademarks and logos of Shenzhen Hongdian Technologies Corporation.
H8951 3G SOHO Router User Manual Contents CONTENTS CHAPTER 1 ABOUT THIS MANUAL .......................................................... 4 1.1 Purpose................................................................................... 4 1.2 Applicable scope ...................................................................... 4 1.3 Version information .................................................................. 4 1.4 Convention .......................................................................
H8951 3G SOHO Router User Manual Chapter1: About This Manual Chapter 1 About This Manual This chapter briefly describes the function and role the this user manual has had, and gives the readers the information on how to read this user manual as the best guideline while Hongdian operated. 1. 2. 3. 4. 5. 6. 1.
H8951 3G SOHO Router User Manual 1.4 Chapter1: About This Manual Convention For reading and using this user manual fast and conveniently, the following conventions are reached for some abbreviations, icons, notes, security warnings and tips that appear in this user manual: Table -1.2: Convention Table Item H8951 H7000 1.
H8951 3G SOHO Router User Manual Chapter1: About This Manual E-mail service: Technical support: Service support@hongdian.com service@hongdian.com Website and BBS service: Website: BBS: 1.6 www.hongdian.com http://www.mdtu.com/forum/default.
H8951 3G SOHO Router User Manual Chapter1: About This Manual ETSI European Telecommunications Standards Institute GGSN Gateway GPRS Support Node GMSC Gateway MSC GPRS General Packet Radio Service GSM Global System for Mobile Communications GSN GPRS Support Node GTP GPRS Tunneling Protocol GTP-id GTP Identity HLR Home Location Register HSCSD High Speed Circuit Switch Data IGMP Internet Group Management Protocol IGRP Internet Gateway Routing Protocol IN Intelligent Network IP Inte
H8951 3G SOHO Router User Manual Chapter1: About This Manual PCF Packet Control Function PDP Packet Data Protocol PDN Packet Data Network PDSN Packet Data Service Node PLMN Public Land Mobile Network POS Point of Sales PTM-G Point-to-Multipoint Group Call PTM-M Point-to-Multipoint Multicast QoS Quality of Service RA Routing Area RADIUS Remote Authentication Dial In User Service RIP Routing Information Protocol RSC Register Service Center RTOS Real Time Operating System RTP Rea
H8951 3G SOHO Router User Manual Chapter2: Product Introduction CHAPTER 2 Product Introduction 2.1 Galaxy 3G overview Combining with the third generation of mobile communication technology and WLAN technology, Galaxy 3G mobile network data communication terminal product is designed as a high-tech 3G product upon the needs of SoHo users. It can provide data communication service for these users at any time and in any place.
H8951 3G SOHO Router User Manual Chapter2: Product Introduction Fig. 2.1.1-1: H8951 Appearance Panel introduction Galaxy H8951 3G SOHO Router features black plastic shell on which there are indicators on its front panel as shown below: Front panel Fig. 2.1.1-2: Front Panel The indicators on the front panel are described as the table below: Indicator Status Description SYSTEM: System status indicator. It is constantly on when the power supply is normal; Wireless Network Modem indicator.
H8951 3G SOHO Router User Manual WIFI: LAN1~2: WAN: Chapter2: Product Introduction WIFI working status indicator. It flashes slowly under the normal working conditions; LAN port 1~LAN port 2 working status indicator. It is on under the normal network connection, otherwise is off. It flashes when the port receives/sends data; WAN port working status indicator. It is on under the normal network connection, otherwise is off. It flashes when the port receives/sends data.
H8951 3G SOHO Router User Manual Chapter2: Product Introduction 2.1.2 Other fittings For safe transportation purpose, Galaxy H8951 3G SOHO Router should be packaged properly. Pease keep the packaging materials well after the package is opened for future use in case of re-transportation.
H8951 3G SOHO Router User Manual Chapter2: Product Introduction 2. This product is a Class-A information product, which may cause radio interference in living environment when being used. In this case, the users are required to take some proper measures. 2.1.3.2 Wiring RJ-45 - Ethernet interface Standard 10/100BaseT Ethernet switch port, self-adaptive (hardware version>2.
H8951 3G SOHO Router User Manual Chapter2: Product Introduction 2.2.2 Software function Internet access Broadband network and private network access by WAN port xDSL broadband network access by PPPoE dial Private network access by static IP address Dynamic access by DHCP Client Connect to Mobile Network by Embedded Wireless Modem Advanced Embedded Wireless Modem driver management 2.5G+ (CDMA, GPRS, EDGE) wireless mobile network access 3G+ (HSDPA/HSUPA, TD-SCDMA/HSDPA, EVDO etc.
H8951 3G SOHO Router User Manual Chapter2: Product Introduction Add/delete static router Inquire system router’s route table in real-time manner NAT/NAPT One-to-one address (IP address/port) mapping management Multi-to-one address (IP address /port) mapping management Free access to host from Internet and Intranet by DMZ host function Route mode IP Masqurade (IP address masquerading) Shared Internet assess Packet filter function Address filter IP address filter rule
H8951 3G SOHO Router User Manual WEB upgrade management PC tools upgrade Chapter2: Product Introduction parameters configuration backup and restoration function Reboot function Time management Manual time setting NTP synchronization Running status information management 2.3 System application Galaxy H8951 3G SOHO Router has two fast and self-adaptive 10M/100M Ethernet switch ports (LAN port), and one fast 10/100M Ethernet WAN port.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Chapter 3 Router Configuration 3.1 Overview Galaxy H8951 3G SOHO Router features built-in WEB interface configuration, management and debugging tools. Before using Galaxy H8951 3G SOHO Router, users should configure relate parameters; during using, you can freely change related parameters and perform software upgrade and simple test etc.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.2.2.1: Wiring Method 1 Note: Galaxy H8951 3G SOHO Router’s LAN port is designed with self-adaptive cross connect technology, so the straight-through cable or cross cable can be both applied to connect devices for communication. 3.2.2.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration corresponding to the network card on this page. Refer to the figure below. Fig. 3.2.3-1: Computer Local Connection Configuration Enter (double click or right click) the “Local Area Connection”“Property (R)” and enter the interface shown in the figure below: Fig. 3.2.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.2.3-3: TCP/IP Properties Configuration Method 1: general configuration This method will temporarily interrupts the communication between the computer under configuration and LAN, and the specific parameter configuration is shown as below: IP address: 192.168.8.* (*indicates any integral between 2 to 254) Subnet mask: 255.255.255.0 Default gateway: 192.168.8.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration If you don’t want to interrupt local PC LAN communication and configure Galaxy H8951 3G SOHO Router when the former network configuration exists, it is required add route (IP). The configuration operation is shown as below: Click the “Advanced (V)…”button in Fig. 3.2-5 to enter the interface as below: Fig. 3.2.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration After the configuration is completed, click the “Add”. By now the computer has a route to Galaxy H8951. Note: As shown in Fig. 3.2-3, “Default gateway” depends on whether the configuration computer connects with Internet through original local network configuration.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.2.4-1: Web Login And then you can enter user login identity authentication interface as shown below: Fig. 3.2.4-2: User Login Verification User should use default user name and password when log in for the first time: User name: admin Password: admin Input correct user name and password, and enter the WEB configuration interface. 3.3 WEB-based configuration Galaxy H8951 3G SOHO Routers can be configured in WEB mode.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3-1: System Configuration Interface WLAN Configure is to configure the wireless LAN quickly. Internet Configure is to configure Internet access quickly. Advance Configure is to configure all of the router’s information. Note: WLAN Configure& Internet Configure are included in the Advance Configure. Click the “Advance Configure” button to go to the configuration interface as shown below: Menu description Fig. 3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Move the mouse pointer onto one tab; click this tab to enter the corresponding sub-tab list or configuration page. The function of each sub-tab and configuration page will be described in the following sections. 3.3.1 Home When you click the “Home” tab, you will return to the page showed default. Fig. 3.3.1: Sub-tabs 3.3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.2.1-1: Mobile Network 【Auto-Dialup】: Set the account number of 3G network service provided by ISP. 【Module Modem Chat Script】: Set the dial-up script chatting with Module Modem. Select the “Customize”, and enter the dial-up script chatting with Module Modem in the input box. Normally you may select”Default”. 【Service Code】: Set the name of 3G network service provided by ISP.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.2.1-2: PPP Advanced Settings Considering the difference of mobile network authorization, the Point to Point Protocol connection should be compatible with different network. Advanced setting is used for the PPP special setting. Click “PPP Advanced Setting” button to start settings.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Normally, it is not required to change the setting for most of networks and applications. If it is necessary, you need to be cautious in setting PPP Advanced based on the network environment. For detailed configuration, consult the local mobile operator and carry out multiple trials to achieve the best suitability. 【CHAP, PAP, MS-CHAP, MS-CHAPv2】are negotiation protocol types while PPP dialing.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.2.2-1: Static IP Configuration Interface WAN port support three static IP address settings: 【WAN IP Address】: Set the IP address, generally subject to ISP or connected device interface. 【Subnet Mask】: Set the IP subnet mask. 【Gateway】: Set the IP address that is in the same network segment with the static IP, generally the IP address provided by ISP, or the IP address of the connected device interface.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.2.2-2: Static IP Configuration Interface After the configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Setting】: Link to the sub-page corresponding to the Internet Connection Type. 【Save】: Save the settings. 【Cancel】: Cancel the unsaved configuration. 【Refresh】: Refresh the information on the page. 3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration 【Internet Connection Type Settings】: Link to the sub-page: Internet Connection Type. After the configuration is completed based on demand, the following operation can be carried out to deal with the configuration result: 【Save】: Save the settings. 【Cancel】: Cancel unsaved configuration. 【Refresh】: Refresh the information on the page. 3.3.2.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.2.3-2: Wan Configuration Interface 【Gateway】: Differ from the wan setting. 【DNS Customize】: Set whether configure the DNS server address manually: Enable/Disable. 【DNS1】: Set IP address of the primary DNS server. 【DNS2】: Set IP address of the standby DNS server. 【VPN Route Type】: Set whether all the packets will pass through VPN even the access to the Internet. 3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration 3.3.3.1 LAN configuration In the “Local Network” main tab, click the “LAN” sub-tab to set the LAN port and enter the following configuration interface: Fig. 3.3.3.1: Local LAN Configuration In this interface, you can set the host name, local IP address and its subnet mask: 【Host Name】: Set the router’s host name. 【Local IP Address】: Set the local IP address. 【Subnet Mask】: Set the subnet mask of the local IP address.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.3.2: Wi-Fi Basic Configuration 【Wireless Status】: Set whether enable the wireless network function: Enable/ Disable. 【Wireless Mode】: Select the wireless network mode: AP by default. 【Wireless Network Mode】: Set the wireless network’s protocol standard: “B-only” is 802.11b standard; “G-only” is 802.11g standard; and “Mixed” is automatically compatible with these two standards.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.3.3-1: Wi-Fi Security Configuration 【Security Mode】: Set the security mode. Select one mode from the drop-down list: Disable, WEP, WPA-PSK, and WPA2-PSK. Now I will explain every mode: Fig. 3.3.3.3-2: WEP Mode Configuration 【Encryption】: Select the key’s length from the drop-down list: 64-bits 10 hex digits, 128-bits 26 hex digits, 5 bits ASCII, and 13 bits ASCII. 【WEP Shared Key】: Set the shared key.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.3.3-3: WPA-PSK Mode Configuration 【WPA Algnorithms】: Select the encryption algorithms from the drop-down list: TKIP, AES, TKIP+AES. 【WPA Shared Key】: Set the shared key (8~23 characters long). 【WPA Renewal Interval】: Set the key’s renewal interval in second. Fig. 3.3.3.3-4: WPA2-PSK Mode Configuration 【WPA Algnorithms】: Select the encryption algorithms from the drop-down list: TKIP, AES, TKIP+AES.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.3.4: DHCP Configuration Interface The configuration parameters include: 【DHCP Server】: Set whether enable the DHCP server function: Enable/Disable. 【IP Address Range】: Set the range of the DHCP dynamic address pool. 【DHCP Reservation】: Set the IP address assigned to the client manually. Click the “IP-MAC Mapping” button to link to the Static DHCP page.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.3.5-1: WAN Configuration Interface The configuration parameters include: 【Add】: Map the DHCP client’s MAC address with IP. 【Del】: Delete or release the mapping of MAC and IP. 【Refresh】: Refresh the information on the page. If you want to perform IP-MAC mapping, click the “Add” button to go to the following configuration interface: Fig. 3.3.3.5-2: WAN Configuration Interface 【MAC Address】: Set the MAC address.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.4: Applications Configuration Tab 3.3.4.1 DDNS configuration The router is designed with DDNS (Dynamic Domain System) function which can make others to search the dynamic IP address by internet domain. In the “Application” main tab, click the “DDNS” sub-tab to set DDNS parameters and go to the following configuration interface: Fig. 3.3.4.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration After each configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Save】: Save the settings. 【Refresh】: Refresh the information on the page. 3.3.4.2 Timing Operation configuration In the “Applications” main tab, click the “Timing Operation” sub-tab to set the Timing Operation parameters and go to the following configuration interface: Fig. 3.3.4.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.4.2-2: Timing Operation Configuration Interface Timing Operation configuration parameters include: 【Name】: Set the name of new Timing Operation. 【Status】: Set whether enable the Timing Operation. 【Action】: Decide execute which type of operation. There are three kinds: online, offline, reboot. (Command is unviable temporarily). 【Set Time】: We have five types of time: minute, hour, day, month and week.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.4.3: Timing Operation Configuration Interface Trigger On-line Data parameters include: 【Status】: Set whether enable the Trigger On-line Data. 【Time limit for idle offline】: Decide the time limit of offline when the router has no data transaction for a period. The value's unit is 'second', 0 means the router will always on line. 【Dial-up overtime】: Set the give up time limit when the router cannot connect to the internet.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.5-1: Filter Setting Interface The configuration parameters include: 【Firewall Service】: Set whether enable firewall function: Enable/Disable. 【Default Action】: Set the default action of the firewall: “Accept” means the router accepts other packets by default; “Drop” means the router drops other packets by default. 【PING Accept】: Set whether allow PING router from outside.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.5-3: Firewall Setting Interface The configuration parameters include: 【ID】: Set the identification of the firewall rule, generally using a name with meanings. 【Protocol】: Select the protocol of the firewall rule. 【Source IP/Mask】: Set the source IP address of the firewall rule, may be one IP address or one network segment, e.g.: 192.168.0.0/24. 【Source Port】: Set the source port number of the firewall rule.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration 【MAC Address】: Set the MAC address. 【Action】: Select the actions to this rule of the firewall: Accept, Drop, Reject. 【Status】: Set whether enable this filter rule: Enable/Disable. After each configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Save】: Save the settings. 【Cancel】: Cancel the unsaved configuration. 【Return】: Return to the previous page. 3.3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration After each configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Add】: Add new L2TP setting. 【Refresh】: Refresh the information on the page. Click the “L2TP” tab; the following sub-tabs appear on the page: Fig. 3.3.6.1-2: L2TP Setting Interface L2TP configuration parameters include: 【Name】: Set a name for this L2TP connect.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.6.2-1: PPTP Setting Interface 【Edit】: Edit the PPTP setting. 【Del】: Delete the PPTP setting. 【View】: View the status of PPTP, including Received Packets (TX), Received Errors Packets, Received Drops Packets, Received Bytes (RX), Send Packets (STX), Send Errors Packets, Send Drops Packet, and Send Bytes (SRX). 【VPN Route Type】: Link to the sub-page: Internet Connection Type.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.6.2-2: PPTP Setting Interface PPTP configuration parameters include: 【Name】: Set a name for this PPTP connect. 【Status】: Set whether enable this PPTP: Enable/Disable. 【Server IP or Domain】: Input Server IP or Domain of the VPN service provider. 【User Name】: Set the user name provided by the VPN SP. 【Password】: Set the password provided by the VPN SP. 【PPP Configures】: Please see Chapter 3.3.2.1 as a reference.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration In the “Forward” main tab, click the “NAT&DMZ” sub-tab to set the route mode, NAT and DMZ functions and go to the following configuration interface: Fig. 3.3.7.1-1: NAT&DMZ Setting Interface NAT&DMZ configuration parameters include: 【NAT/NAPT Services】: Set whether enable NAT/NAPT function: Enable/Disable. 【DMZ Services】: Set whether enable DMZ function: Enable/Disable.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.7.1-2: NAT&DMZ Setting Interface 【Select】: Select which data forward rule to be added. 1. Route mode setting Select the “Route Mode” option to go to the following configuration interface: Fig. 3.3.7.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.7.2-4: DMZ Setting Interface DMZ configuration parameters include: 【Outside Interface】: Set the interface on which the DMZ function acts. 【Inside Address】: Set the IP address of the host assigned by DMZ record. After the configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Save】: Save the settings. 【Return】: Return to the previous page. 3.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration NAT configuration parameters include: 【Name】: Set the name mapped by NAT port. 【Protocol】: Set the protocol mapped by NAT port. 【Outside Interface】: Select the interface on which NAT function acts. 【Outside Port】: Set the outside port number mapped by NAT port. 【Inside Address】: Set the IP address of LAN host mapped by NAT port. 【Inside Port】: Set the port number of LAN host mapped by NAT port.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.7.2-2: Static Route Configuration Interface The static route’s configuration parameters include: 【Destination IP】: Configure the destination network address of this static route. 【Subnet Mask】: Configure the subnet mask of the destination address of this static route. 【Gateway】: Configure the next IP address of this static route, namely the port address of the neighboring router.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration In the “System Tools” main tab, click the “Local Log” sub-tab to view the log information and go to the following configuration interface: Fig. 3.3.8.1: Log View Interface Log view settings include: 【System Log】: Set the type of log to be displayed. After selecting the log type, you can make the following operations: 【Show】: Display log in the Log Table. 【Clear】: Clear the log in the Log Table.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.8.2: System Log Management Interface The system log configuration parameters include: 【Local Log Status】: Set whether enable local log function: Enable/Disable. 【Remote Log Status】: Set whether enable remote log function: Enable/Disable. After this function is enabled, the router will send the log information to the configured remote PC.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.8.3: NTP Configuration Interface The system clock configuration parameters include: 【NTP Server IP】: Set the domain or IP address of the NTP server. 【NTP Synch. Interval】: Set the interval of the router making NTP synchronization in successive two times. 【Time Zone】: Set the time zone. After the configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Synch.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration The system clock configuration parameters include: 【Input New Password】: Input your new password. 【Please Input New Password Again】:Input your new password again After the configuration according to your specific needs, you can carry out the following operations to the configuration result: 【Save】: Save the settings. 【Refresh】: Refresh the information on the page. Then you need to log in to the router again. 3.3.8.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration Fig. 3.3.8.5-2: Restoration Configuration Interface The configuration file restoration operations include: 【Select】: Select the location where the parameters file to be imported is located. 【Restore】: Import the parameters. 【Cancel】: Cancel the information in the address input box.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration 3.3.8.6 Firmware upgrade In the “System Tools” main tab, click the “Firmware Upgrade” sub-tab to use the software upgrade function and go to the following interface: Fig. 3.3.8.6: Upgrade Management Interface The upgrade configuration parameters include: 【Select】: Select the location of the upgrade software. 【upgrade】: Start firmware upgrade. 【Cancel】: Cancel the unsaved configuration. 【Refresh】: Refresh the information on the page.
H8951 3G SOHO Router User Manual Chapter3: Router Configuration After reboot the router, please reboot the browser! 3.3.9 Status display When you click the “Status” tab, the following sub-tabs appear on the page: Base Information LAN WAN Embedded Modem Route Table DHCP Client Fig. 3.3.9: Status Information Tab Tab description: 【System Information】: Display the system information. 【LAN】: Display LAN port’s running information. 【WAN】: Display WAN port’s running information.
H8951 3G SOHO Router User Manual Chapter4: Frequently Asked Questions (FAQ) Chapter 4 Frequently Asked Questions (FAQ) 4.1 Fault analysis Fault 1: All indicators are off. Check whether the cables are connected correctly. Meanwhile, check whether the power supply complies with the requirements. Galaxy H8951 3G SOHO Router’s label indicates the detailed requirements regarding the power supply voltage. Check whether the power supply voltage is identical with that specified in the label.
H8951 3G SOHO Router User Manual Chapter4: Frequently Asked Questions (FAQ) C:\>ipconfig Windows IP Configuration Ethernet adapter local connection: Connection-specific DNS Suffix. . . . : IP Address . . . . . . . . . . . . . . . . . . . : 192.168.8.48 Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0 IP Address . . . . . . . . . . . . . . . . . . : 192.168.0.48 Subnet Mask . . . . . . . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . . . . . . : 192.168.0.
H8951 3G SOHO Router User Manual Appendix Appendix: Software Upgrade Description Upgrade tool description and operating instructions Galaxy H8951 3G Router is designed with the platform technology, whose software can be upgraded with the development of the communication and network technology. WEB upgrade: Galaxy H8951 3G Router supports the function of upgrading the firmware directly by importing the upgrade file via the WEB configuration interface.
