WiFi-Zigbee Gateway HGW501 User Guide iOS Android
System requirement................................................................................. Application installation............................................................................ WiFi settings................................................................................................. Enter application..................................................................................... Add device.......................................................................................
1 System requirement Android2.3 and above iOS 6.0 and above 2 Application installation Scan QRCode, and install application. 3 WiFi settings Power on the gateway. Please select the WLAN iLightsInxxxxxx on mobile settings menu. The xxxxxx is the mac address on back of gateway. Connect the WiFi AP, and open installed application(Picture1,2). Attention : The gateway can be set to connect another router on application setting menu. See chapter 9.2 Network settings.
图1 图2 图3 5 Add device Enter Settings menu/ Add device with 2 methods to add device(picture3,4). a) Add device by QRCode scanning. Each of device has one QRCode. Usercan scan QRCode to add device in application(Picture5).Save the scanned device and check it by Testing button(Picture6).
Picture4 Picture5 Picture6 Attention: The device and gateway has to be power on while test button is pressed, but the device can be power off while scanning QRcode to add device. And the gateway has to be power on when enter Add device or Add group menu. b) Add device by pairing. The following are steps to add device by pairing mode 1.First input the device name and select correct device type.
Picture7 Picture8 Picture9 2.Activate the device pairing mode by power on device (some device will be on pairing mode in 5 seconds after power on). Or user also can activate pairing mode by press the key of device. 3.Save the device while device is on pairing mode (The pairing command will be sent to device while save button is pressed)(Picture7, 8). Attention: a.
Picture10 Picture11 Picture 1 2 b. The following is the definition to activate pairing mode for different device. Product LED Driver 6 Scenes 6.
Press to Scene menu. The application can support scene based on settings in advance . So user can click one scene to reach different status fordifferent devices. Press to add new scene, then input the scene name and select devices and their status( Picture 9). Click to select the device and its status in this scene. Example: create one scene with Sleep name and select all Color temperature light with the color you liked on select devices menu. Click save, then the Sleep scene is created.
7.2 Area Sub Menu Click one area can enter the sub menu and all different device can be listed. User can control each of device in this area(Picture15). User can move the slider to change color or brightness. The lights have to bound with daylight sensor for daylight sensor control. The following is the operation steps.
Picture16 Picture17 Picture18 Attention: Please binding the device before control the daylight sensor.See chapter 9.3 Binding settings. a).Power on lights. Bind the light or group in Settings/Binding settings menu. b).Change the lights brightness to favorite luminance(User can use illuminometer to get favorite luminance).
Picture19 The part Picture20 Picture21 can set different effect, interval and run or stop. Click to enter Timer or delay menu. Under this menu, user can set the timer or delay and different status while timeout (Picture18,19,20). User can store the power on color for Color temperature light(Picture21). User select different type device by the following icons (Picture22).
Picture22 Picture23 Picture24 7.3 Edit area User can long press the area button on area menu to edit area or delete area (Picture23). 8 Add group/Edit group User can put the same type devices in one group. So all same type devices in this group can be controlled at same time.(Picture24,25) Attention: The devices must power on while group setting is saved.
Picture25 9 Settings Click to enter settings menu. Picture26 Picture27 9.1 Import data/Export data All devices , scene and area are stored on client as database. Please back up your database after all devices, scene and area adding done. Apps support database synchronization between 2 clients(Picture26,27,28). a. Import or export database from SD card or to SD card.
Picture28 Picture29 Picture30 b. Import database from another mobile, MID or PC by LAN Attention: Clients can not synchronize database on iLightsInxxxxxx router c. Import or export database from gateway. 9.2 Network settings The gateway also can join another WiFi router for remote control. Attention: The gateway will recover the default settings after the setting is failed with wrong SSID, encryption type or password.
9.3 Binding settings(Picture29,30,31,32,33) a).Open Add device, select Add by QRcode, Scan the QRcode back of touch dimmer. b).Input name and save. Then the touch dimmer has to bound with lights before light control. c).Handheld dimmer has to press any key before Click Save. d).User can bind the remote control, handheld dimmer and sensor with lights.
Adapter supply: Model:AEK6W-050100 Input:100-240V 50/60Hz 150mA Max Output:5V,1A FCC Caution: This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
1 2 3 4 5 6 7 8 9 10 11 12
