Instruction Manual

HSD9027E-10 英文说明书(过 QI-10W 无线充电 DC12V/2A)/
Instruction Manual
Main Features & Technical Parameters
● Power supply: Input AC100-240V 50/60Hz, Output DC12V/2A
● Rated working current: 1.7A
● Rated power of product: 22W
● Rated power of lamp: 5.5W
● Dimming type: Capacitive touch button/stepless dimming
● Power Timer: Smart timing lights (on/off auto-control)
● Light source: 36pcs High photosynthetic efficiency semiconductor
LED
● Three types of Light effects to switch: Natural—White—yellow light
● Color temperature: 2700-6500K
● Color rendering index (CRI): Ra≥90
● Max illuminance: ≥ 1000LUX(The Intensity of Illumination
measured from the lamp perpendicular to the table top 31cm
distance)
● Wireless charging output: 10W (MAX）
Operating Instruction
1. Usage method of Lamp: Put the lamp on the table and connect
power at first. And press button, short press button to switch on,
The default light is the natural light, press again to switch off. Short
press light switch “M” button, the lamp light changing circularly
(Natural —White—Yellow light).
2. Brightness adjustment: In lighted state, Long press button to
change brightness of lamp.
3. Timer function: In lighted state, long press to start timer off
function. Then, the light flashes 2 times it means countdown function
starting, and the light will be off automatically in 40 minutes (About
one class time). If you Press again during this period, it will be restart
40 minutes countdown light off function, until end of the countdown
function, the lights automatically turned off.
Wireless Charging Instruction
1. Wireless charging function: Please connect power at first, then,
please put your mobile phone (which one with wireless charging
receiving function) near by the product, and see the reminder show
your mobile phone. If show, means be charging, and the status light is
green of the time.
2. To be the best using effects and charge efficiency, pleas ensure your
mobile phone wireless receiving position is in right way with product
receiving, range. When the status light both green and red, means fully
charged.
Cautions
1. Please ensure using the power supply matching DC12/2A, If the
power adapter or flexible wire is damaged, It only can be replaced by
the manufacturer or agent, or by similarly qualified person.
2. For indoor use only.
3. Please pay attention to eyes hurting while using the lamp, the
distance should not closely.
4. Please make sure the product without strong electromagnetic
interference, otherwise may be lights on or turn off.
5. The hosepipe part of lamp pole can not bent in continuously,
otherwise lead to the lamp pole damage easily.
6. Please change a new one, when the light source is use up, cause of
this light source is can not be alternative.
7. Please pay attention when used on countertops with a tilt greater
than 6 degrees. might be dumping.
8. When using the lamp at night, Please adjust the color temperature
(light effect) under 4000K (like natural light, warm white light) is better.
Product Illustration
Packing Accessories
1. Power Adapter * 1
2. Instruction manual * 1
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a
residential installation. This equipment generates uses and
can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2)
this device must accept any interference received,