Installation Instructions

32.768
kHz Oscillator Comparison
Sym
bol
Pa
rameter
Min
.
Typ.
Ma
x.
Uni
t
I
LFXO
Curre
nt for 32.768kHz Crystal
Os
cillator
-
0.25
-
µA
I
LFRC
Curre
nt for
32
.768kHz RC
Os
cillator
-
0.6
1
µA
I
LFSYNT
Current for 32.768kHz Synthesized Oscillator
-
100
-
µA
f
TOL_L
FXO_BLE
Frequen
cy Tolerance, 32.768kHz Crystal
Oscill
ator
(BLE S
tack)
1
- - ±25
0 ppm
f
TOL_L
FXO_ANT
Frequen
cy Tolerance, 32.768kHz
Crys
tal
Oscill
ator
(ANT Stac
k)
1
- - ±50
ppm
f
TOL_
LFRC
Frequen
cy Tolerance, 32.768kHz RC
Osc
illator
-
-
±2
%
f
TOL_C
AL_LFRC
Frequen
cy tolerance, 32.768kHz RC after calibration
-
-
±25
0
ppm
f
TOL_L
FSYNT
Frequen
cy Tolerance, 32.768kHz
Syn
thesized
Os
cillator
- - ±48 ppm
Not
e 1: f
TOL
_LFXO_BLE and
f
TOL
_LFXO_ANT
are
the max allowed for BLE and ANT applications. Actual tolerance depends
on
the crystal used.
Tab
le 11 – 32.768 k
The module meet the requirement of FCC Part 15.247
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20cm between the radiator and any part of your body.
Remind end customers to FCC ID label on the final system must be labeled with “Contains FCC ID: 2AW5Y300” or “Contains transmitter module
FCC ID: 2AW5Y300”.
Contact ShenZhen High Speed Technology Co.,Ltd will provide stand-alone modular transmitter test mode. Additional testing and certification may
be necessary when multiple modules are used in a host.
To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed
and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Supplier’s Declaration of Conformity
procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the
module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may
depend on the details of how the module is integrated with the host, ShenZhen High Speed Technology Co.,Ltd shall provide guidance to the host
manufacturer for compliance with the Part 15B requirements.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.This module certified that complies with RF exposure requirement under mobile or fixed
condition, this module is to be installed only in mobile or fixed applications. A separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and difference antenna configurations.This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
NOTE 1: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver.—Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
NOTE 3: Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be
sold to end-users, end-user has no manual instructions to remove or install the device, only software or operating procedure shall be placed in the
end-user operating manual of final products.
NOTE 4: The module may be operated only with the antenna with which it is authorized. Any antenna that is of the same type and of equal or less
directional gain as an antenna that is authorized with the intentional radiator may be marketed with, and used with, that intentional radiator.